88 5170 943
Kitchen Island
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Part List
E.
Base
1 pc.
F.
Shelf
4 pcs.
J.
Door
1 pc.
K.
Door
1 pc.
Hardware List
Hex Wrench
1 pc.
Adjustable Pin
16 pcs. (+1 extra)
G.
Front Rail
2 pcs.
L.
Back Rail
2 pcs.
Cam Lock
18 pcs.(+6 extra)
M x388
Head Cap Bolt
6 pcs. (+1 extra)
H.
Back Upright
1 pc.
M3x15
Wood Screw
for back panel
8 pcs. (+1 extra)
I.
Back Panel
2 pcs.
M.
Drawer
2 pcs.
Refer to later page(s) of these
instructions for drawer assembly.
M3x15
Wood Screw
4 pcs. (+1 extra)
M4x25
Machine Screw
6 pcs.
Small
Hex Wrench
1 pc.
Wood Dowel
6 pcs.
Cam Lock Screw
18 pcs.(+2 extra)
Flat Washer
6 pcs. (+1 extra)
Spring Washer
6 pcs. (+1 extra)
Magnet
2 pcs.
Knob
6 pcs.
Cartons 88 5523 94Q1 or 941 and 942 are also needed for assembly.
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/8” Drill Bit
Home Styles Customer Service: www.homestyles-furniture.com,
servicedesk@homestyles-furniture.com,
888-680-7460, 877-831-0319
Assembly Instructions 2/5
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the screws until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench in a safe place as the bolts may need to be tightened up in the future.
Cam Lock Screw
A
STEP 1
Put Cam Lock Screws into
the pre-drilled holes of Top (A),
Side Panels (B), (C) and Base (E) and tighten.
(See Figure 1)
B
Cam Lock Screw
C
Cam Lock Screw
E
Figure 1
Assembly Instructions 3/5
STEP 2
Cam Lock
L
C
I
H
I
L
Attach Back Rails (L) to Side Panel (C) with Cam Locks.
(See Figure 2)
Slide Back Panel (I), Back Upright (H) and Back Panel (I)
to unit.
Figure 2
Figure 3
Cam Lock
STEP 3
Attach Front Rails (G) and
Middle Panel (D) to unit with Cam Locks.
Attach Side Panel (B) to unit with
Cam Locks.
E
D
B
G
G
Head Cap Bolt
Spring Washer
Flat Washer
STEP 4
Cam Lock
Attach Base (E) to unit with Flat Washers,
Spring Washers, Head Cap Bolts and Cam Locks.
(See Figure 3)
Drawer (M)
M4
Lock
M2
Roller at back
Assembly Instructions 4/5
STEP 5
Attach Drawer Sides (M3) and (M4) to
Drawer Back (M2), then flip the locks.
(See Figures 4 and 5)
M3
STEP 6
Slide Drawer Bottom (M5) into the
grooves in Drawer Sides (M3) and (M4).
Push Drawer Bottom (M5) all the
way into Drawer Back (M2).
Attach Drawer Front (M1) to
unit, then flip the locks.
Figure 4
M4
M1
M5
M2
M3
STEP 7
Attach Knob with Machine Screw.
Figure 5
Part List
M1.
Drawer Front
2 pcs.
M2.
Drawer Back
2 pcs.
M3.
Drawer Side
2 pcs.
M4.
Drawer Side
2 pcs.
M5.
Drawer Bottom
2 pcs.
Assembly Instructions 5/5
Cam Lock
STEP 8
Wood Dowel
Turn the unit to its’ upright position, then insert
Wood Dowels into side panels and middle panel.
Attach Top (A) to unit with Cam Locks.
Attach Magnets to unit with Wood Screws.
(See Figure 6)
Level unit by adjusting the adjustable levelers
on the bottom of unit. (See Figure 7)
Insert Wood Screws for back panel into
pre-drilled holes of unit.
Wood Screw
for back panel
A
Note: Unit must be level before tightening
these screws.
Figure 6
Figure 7
Magnet
Wood Screw
Figure 8
Wood Screw
for back panel
Figure 9
STEP 9
Slide Drawers (M) into position.
J
Adjustable Pin
F
F
M
F
F
M
K
Insert Adjustable Pins into side
panel and middle panel at
desired level, then place
Shelves (F) into position.
Attach Doors (J) and (K) by sliding
the door lift hinges into the side
panels lift hinges. (See Figure 8)
Assemble Knobs to Doors (J) and (K)
with Machine Screws. (See Figure 9)
CARE INSTRUCTIONS
NEVER
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
Do not write
directly on surface.
PREVENT
MARKING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
CLEAN
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is underno obligation to provide replacement parts. Parts are not available forfully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
servicedesk@homestyles-furniture.com,
888-680-7460, 877-831-0319
Loading...