Home Styles 5660-30 User Manual

88 5660 30
Bali Hai
Extension Table
IMPORTANT NOTE
Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the parts.
Part List
A. Top
1pc
B. Top
1pc
C. Top
1pc
D. Block
2 pcs
G. Support
1pc
E. Leg Support
1pc
H. Support
1pc
I. Leg
2 pcs
F. Leg Support
1pc
J. Leg
2 pcs
N. Stretcher
1pc
K. Support
2 pcs
L. Rail
1pc
M. Pipe
1pc
O. Stretcher
1pc
Hardware List
Small Hex Wrench 4mm
1 pc.
Hex Wrench 4mm
1pc
Assembly Screw
4 pcs.(+1 extra)
Wood Screw (Long)
4 pcs.(+1 extra)
Tools required for assembly : Phillips screwdriver
Home Styles Consumer Assistance: www.homestyles-furniture.com, servicedesk@homestyles-furniture.com, 888-680-7460, 877-831-0319
Head Cap Bolt (Long)
4 pcs.(+1 extra)
Wood Screw (Short)
2 pcs.(+1 extra)
Head Cap Bolt (Middle)
8 pcs.(+1 extra)
Dowel
4 pcs.(+1 extra)
Cover
1 pc.
Head Cap Bolt (Short)
8 pcs.(+1 extra)
Cover
2 pcs.
Assembly Instructions 2/4
IMPORTANT
* Do not tighten up all the screws until each part is properly assembled. * You should keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* Use a soft cloth between these parts and the floor.
STEP 1
Attach Stretcher (N) to Stretcher (O), with Wood Screws (Short).
O
Wood Screw (Short)
Head Cap Bolt (Middle)
N
I
STEP 3
F
L
STEP 2
J
I
Attach Leg Supports (E) and (F) to Legs (I) and (J) with Assembly Screws.
Attach Rail (L) to Leg Supports (E) and (F).
Attach unit from Step 1 to Legs (I) and (J) with Head Cap Bolts (Middle).
E
J
Assembly Screw
Head Cap Bolt (Middle)
Attach Blocks (D) to Pipe (M).
Attach Pipe into the pre-drilled holes of Supports (G) and (H).
Attach Supports (K) to Supports (G) and (H) with Head Cap Bolts (Middle).
G
K
K
M
D
H
STEP 4
Assembly Instructions 3/4
Attach Top (B) to unit from Step 3 with Wood Screws (Long) into the pre-drilled holes.
Head Cap Bolt (Short)
Head Cap Bolt (Long)
Wood Screw (Long)
B
STEP 5
Place the unit from Step 2 in an upright position.
Attach unit from Step 4 to unit from Step 2 with Head Cap Bolts (Long) and Head Cap Bolts (Short).
STEP 6
Attach Top (A) and (C) to unit by sliding into the groove in Supports (K).
Insert the Dowels into the holes of the rail in bottom side of Tops (A) and (C). (See figure 1)
A
C
Figure 1 (bottom view)
Dowel
Assembly Instructions 4/4
STEP 7
Put Covers into the holes of the top when not using an umbrella.
Lock
Close
Figure 2 (bottom view)
To Shorten the Table
Covers
Open
Open the locks under the top. (See Figure 2)
Pull the half tops slightly apart, fold up the center top and rotate it so that it fits into the table base.
Push the half tops together.
Close the locks under the top. (See Figure 2)
Loading...