Page 1
88 5549 101
Crescent Hill
Entertainment Credenza
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damage occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Part List
A.
Top
1 Pc.
L.
Base
1 Pc.
I.
Shelf
4 Pcs.
Hardware List
Hex Wrench
1 Pc.
Cam Lock
12 Pcs. (+4 extra)
M6x25
Head Cap Bolt (short)
4 Pcs. (+1 extra)
M.
Leg
1 Pc.
Flat Washer
8 Pcs. (+1 extra)
J.
Door
1 Pc.
N.
Leg
1 Pc.
M3x15 M3x15
Tapered Wood Screw
4 Pcs. (+1 extra)
K.
Door
1 Pc.
O.
Leg
1 Pc.
Wood Screw
12 Pcs. (+1 extra)
P.
Leg
1 Pc.
Pull Handle
2 Pcs.
M4x25
Machine Screw
4 Pcs.
Small Hex Wrench
1 Pc.
Cam Lock Screw
12 Pcs. (+1 extra)
M6x50
Head Cap Bolt (long)
8 Pcs. (+1 extra)
Spring Washer
8 Pcs. (+1 extra)
Magnet
2 Pcs.
Adjustable Pin
24 Pcs.
For assembly see instructions in carton 88 5549 102
Tools required for assembly : Phillips screwdriver Tools recommended for assembly : Level
Home Styles Consumer Assistance: www.homestyles-furniture.com,
servicedesk@homestyles-furniture.com, 888-680-7460, 877-831-0319
Page 2
88 5549 102
Crescent Hill
Entertainment Credenza
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damage occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Part List
B.
Side Panel
1 Pc.
H.
Shelf
2 Pcs.
C.
Side Panel
1 Pc.
F.
Back Panel
2 Pcs.
D.
Middle Panel
1 Pc.
Also need the following from carton 88 5549 101 :
E.
Middle Panel
1 Pc.
G.
Back Panel
1 Pc.
Tools required for assembly : Phillips screwdriver Tools recommended for assembly : Level
Home Styles Consumer Assistance: www.homestyles-furniture.com,
servicedesk@homestyles-furniture.com, 888-680-7460, 877-831-0319
Page 3
Assembly Instructions
IMPORTANT
* Please keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* Do not tighten up all the bolts until each part is properly assembled.
* Use a soft cloth between these parts and the fl oor.
* After assembly item must be level to work properly. Use the included adjustable levelers to level.
3
/4
STEP 1
Place Base (L) upside down on
a soft cloth then attach Legs (M),
(N), (O) and (P) to Base (L) with
Flat Washers, Spring Washers
and Head Cap Bolts (long).
(See Figure 1)
Figure 1
Cam Lock Screw
N
P
Head Cap Bolt (long)
Spring Washer
Flat Washer
L
O
M
STEP 2
Turn the unit over to its’ upright position.
Magnet
Insert Cam Lock Screws into pre-drilled
holes of the unit and Top (A).
(See Figure 2)
Attach Magnet to Top (A) with
Tapered Wood Screws. (See Figure 3)
Cam Lock Screw
Figure 2
A
Tapered Wood Screw
Figure 3
Page 4
STEP 3
Assembly Instructions
4
/4
Attach Side Panels (B) and (C) with
Head Cap Bolts (short).
F
D
G
E
B
Head Cap Bolt (short)
STEP 4
Turn the unit over to its’ upright
F
position.
Attach Middle Panels (D) and (E) to
the unit with Cam Locks.
(See Figure 4)
C
Figure 4
STEP 5
Attach Top (A) to the unit with Cam Locks.
Insert Adjustable Pins into side panels and
middle panels at the desired level.
Slide Back Panels (F) and (G) into
position.
Cam Lock
A
Cam Lock
Adjustable Pin
I
H
I
I
H
I
Place Shelves (H) and (I) into position.
Page 5
STEP 6
Attach Pull Handles to Doors (J)
and (K) with Machine Screws.
(See Figure 5)
J
Assembly Instructions
5
/4
Attach Doors (J) and (K) to unit
by sliding the door life hinges
into the side panel lift hinges.
(See Figure 6)
Level the unit by adjusting the adjustable
levelers on the bottom of the legs.
(See Figure 7)
Figure 5 Figure 6 Figure 7
K
Wood Screw
STEP 7
Insert Wood Screws into the
pre-drilled holes in the back
panel.
Note : Please make sure unit
is level before tightening
these screws.
Loading...