88 5254 95
Kitchen Cart
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damage occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Part List
D.
Side Frame
1 Pc.
M.
Wine Shelf
10 Pcs.
E.
Side Frame
1 Pc.
N.
Shelf
1 Pc.
A.
Top
1 Pc.
F.
Middle Frame
1 Pc.
G.
Middle Frame
1 Pc.
O.
Door
1 Pc.
B.
Base
1 Pc.
H.
Back Stretcher
1 Pc.
I.
Back Panel
1 Pc.
J.
Back Stretcher
1 Pc.
P.
Arm
2 Pcs.
C.
Back Stretcher
1 Pc.
K.
Back Stretcher
1 Pc.
L.
Front Stretcher
1 Pc.
Q.
Round Arm
1 Pc.
R.
Drawer
1 Pc.
(Please refer to the last page of these
instructions for drawer assembly steps.)
Hardware List
Caster
two lock
two non-lock
4 Pcs.
M4x16
Wood Screw
for Caster
16 Pcs. (+1 extra)
Hex Wrench
1 Pc.
Small Hex Wrench
1 Pc.
Tools required for assembly : Phillips screwdriver
Home Styles Consumer Assistance: www.homestyles-furniture.com,
servicedesk@homestyles-furniture.com, 888-680-7460, 877-831-0319
Cam Lock
16 Pcs. (+1 extra)
Cam Lock Screw
16 Pcs. (+1 extra)
M3.5x25
Wood Screw (long)
8 Pcs. (+1 extra)
M3.5x16
Wood Screw (short)
6 Pcs. (+1 extra)
M4x25
Machine Screw
5 Pcs.
M6x40
Head Cap Bolt
6 Pcs. (+1 extra)
Knob
1 Pc.
Pull Handle
2 Pcs.
Assembly Instructions
IMPORTANT
* Please keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* Do not tighten up all the bolts until each part is properly assembled.
* Use a soft cloth between these parts and the fl oor.
STEP 1
Insert Cam Lock Screws into pre-drilled holes of Top (A),
Side Frame (D), (E) and Middle Frame (G).
(see Figure 1)
D
Cam Lock Screw
A
2
/5
G
Arrow Sticker
Non-Locking Caster
B
Locking Caster
STEP 3
Attach Wine Shelves (M) to Side Frame (D),
Middle Frame (F) and Middle Frame (G).
E
Wood Screw for Caster
Figure 1
STEP 2
Attach Casters to Base (B) with
Wood Screws for Caster putting the
Locking Casters in front.
(see “Arrow” sticker indicating front side)
(see Figure 2)
Cam Lock
Figure 2
Attach Front Stretcher (L) and
Back Stretcher (K) to unit with Cam Locks.
(see Figure 3)
Figure 3
D
M
L
K
F
G
M
STEP 4
Attach Back Stretcher (C) to unit.
Attach Shelf (N) to unit with Cam Locks.
Assembly Instructions
3
C
N
Cam Lock
STEP 5
Attach Back Stretcher (H) and (J) to unit
with Cam Locks.
/5
J
Slide Back Panel (I) into place.
Cam Lock
H
I
E
STEP 6
Attach Side Frame (E) to unit with Cam Locks.
Cam Lock
Arrow Sticker
Assembly Instructions
4
/5
STEP 7
With Locking Casters to the front, attach
Base (B) to unit with Head Cap Bolts.
(see Figure 4)
B
Locking Caster
Non-Locking Caster
Head Cap Bolt
STEP 8
Turn the unit to its upright position.
Attach Arms (P) to unit with
Head Cap Bolts.
Slide Round Arm (Q) into place.
Attach Top (A) to the unit with Cam Locks.
Figure 4
Cam Lock
A
P
P
Q
Head Cap Bolt
STEP 9
Attach Knob to Door (O) with Machine Screw.
(see Figure 5)
R
O
Attach Door (O) by inserting the lower Spring Pin
into the hole until it clicks (see Figure 6) and then
do the same for the upper Spring Pin.
Slide Drawer (R) into place.
Figure 5 Figure 6
Drawer R
Assembly Instructions
5
/5
B
B
R1
B
R1
B
R4
B
R3
B
R2
Figure 1
STEP 2
Slide R5 into grooves in R3 and R4. Be sure
to push R5 all the way forward so it meets R1.
(see Figure 2)
MAKE SURE ROLLER
IS ON THE BACK
B
R3
R5
STEP 1
Attach R1, R2 and R3 using a Phillips
screwdriver and long wood screws (4X),
tighten halfway.
Attach R1, R2 and R4 using
long wood screws (4X), tighten halfway.
(see Figure 1)
B
R3
B
R5
STEP 3
Insert short wood screws (6X)
into the pre-drilled holes in R5,
tighten screws. (see Figure 3)
B
R1
B
R4
Figure 2
B
R2
Figure 3
STEP 4
Attach Pulls Handle with Machine Screws.
(see Figure 4)
Tighten all screws used in drawer assembly.
B
R4
Part List
R1.
Front Part
1 Pc.
R2.
Back Part
1 Pc.
R3.
Side Part
1 Pc.
R4.
Side Part
1 Pc.
Figure 4
R5.
Base Part
1 Pc.
Loading...