88 5181 64
Arts & Crafts Pantry
IMPORTANT NOTE
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damages occuring to the wood parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure a
completed product as it was designed.
Part List
A.
Top
1 pc.
B.
Front Rail
1 pc.
C.
Shelf
4 pcs.
D.
Bottom
1 pc.
E.
Side Panel
1 pc.
F.
Side Panel
1 pc.
G.
Door
1 pc.
K.
Leg Frame
1 pc.
H.
Door
1 pc.
L.
Leg Frame
1 pc.
I.
Back Panel
2 pcs.
M.
Back Rail
4 pcs.
J.
Back Post
1 pc.
N.
Top
1 pc.
O.
Front Rail
1 pc.
P.
Side Panel
1 pc.
Q.
Side Panel
1 pc.
R.
Door
1 pc.
S.
Door
1 pc.
T.
Back Panel
2 pcs.
U.
Back Post
1 pc.
Hardware List
Hex Wrench
1 pc.
Small
Hex Wrench
1 pc.
Cam Lock Screw
28 pcs.(+1 extra)
Cam Lock
28 pcs.(+1 extra)
Wood Screw
for Back Panel
16 pcs. (+1 extra)
Adjustable Pin
16 pcs. (+1 extra)
Head Cap Bolt
4 pcs. (+1 extra)
Flat Washer
4 pcs. (+1 extra)
Tools required for assembly : Tools recommended for assembly :Phillips screwdriver Level
Home Styles Consumer Assistance: www.homestyles-furniture.com,
servicedesk@homestyles-furniture.com, 888-680-7460, 877-831-0319
Spring Washer
4 pcs. (+1 extra)
Machine Screw
8 pcs.
Knob
4 pcs.
Assembly Instructions 2/5
IMPORTANT
* Do not tighten up all the screws until each part is properly assembled.
* You should keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* After assembly, item must be level to work properly. Use the included adjustable levelers to level.
* Use a soft cloth between these parts and the floor.
Cam Lock Screw
A
D
E
F
N
Figure 1
P
Q
STEP 1
Insert Cam Lock Screws into the pre-drilled holes of
Top (A), (N), Bottom (D) and Side Panel (E), (F), (P), (Q).
(see Figure 1)
B
Assembly Instructions 3/5
Cam Lock
STEP 2
E
STEP 3
M
Attach Back Rail (M) to Side
M
I
J
I
Head Cap Bolt
Spring Washer
Flat Washer
F
Panel (F) using a Cam Lock.
Attach Back Post (J) to Back
Rail (M). Slide Back Panels
(I) to the unit. Attach Back
Rail (M) to unit using a Cam
Lock. Attach Front Rail (B) to
unit using a Cam Lock.
Attach Side Panel (E) to the
unit using Cam Locks.
(see Figure 2)
K
D
L
Attach Leg Frames (K), (L) to the Bottom
with Head Cap Bolts, Spring Washers and Flat Washers.
(see Figure 3)
A
STEP 4
Attach unit from Step 2 to unit
from Step 3 using Cam Locks.
Figure 2
Cam Lock
Place Top (A) onto unit using Cam
Locks.
Figure 3
P
Assembly Instructions 4/5
Head Cap Bolt
O
M
T
U
Q
T
M
STEP 5
Attach Back Rail (M) to Side Panel (Q) using a Cam Lock. Attach Back Post (U) to Back Rail
(M). Slide Back Panels (T) to the unit. Attach Back Rail (M) to unit using a Cam Lock.
Attach Front Rail (O) to unit using a Cam Lock. Attach Side Panel (P) to the unit using Cam
Locks.
N
STEP 6
Cam Lock
Place Top (N) onto unit using
Cam Locks.
Cam Lock
STEP 7
Attach unit from Step 6 to unit from
Step 4 using Cam Locks.
STEP 8
Insert Adjustable Pins into side panels at desired location.
Place Shelves (C) into position.
Attach Doors (G), (H), (R) and (S) to the side panels by
sliding the door lift hinges into the side panel lift hinges.
(see Figure 4)
Assemble Pull Handles to Door (G), (H), (R) and (S)
with Machine Screws. (see Figure 5)
Assembly Instructions 5/5
R
C
C
S
Figure 4
Adjustable Pin
Figure 5
G
C
C
H
Figure 6
Wood Screw
for Back Panel
STEP 9
To level the unit, adjust the adjustable
levelers on the bottom of unit.
(see Figure 7)
Insert 16X Wood Screws from
the back of the unit. (see Figure 6)
Note: Please make sure unit is
level before tightening these
screws.
Figure 7
Loading...