88509995 C
Kitchen Center
Dear Our Valuable Customers,
Please follow our assembly instructions in every step,
we guarantee that you will get the perfect merchandise.
Thank you so much for purchasing our quality products.
Casual Attire For Today's Home
PART LIST
A.
Top
1 pc.
G.
Upper Back Stretcher
1 pc.
H.
Lower Back Stretcher
1 pc.
I.
Front Rail
1 pc.
J1.
Back Post
1 pc.
N.
Shelf
2 pcs.
Side Panel
1 pc.
J2.
Back Post
1 pc.
Thai Patent Pending Numbers 086878
D.
Middle Frame
1 pc.
B.
K.
Base
1 pc.
O.
Drawer
O.
2 pcs.
Shelf
2 pcs.
C.
Side Panel
1 pc.
Door
1 pc.
P.
Drawer
2 pcs.
(Knock-Down Construction, please refer
to the last page of these instructions for
steps to complete assembling drawers)
L.
E.
Middle Frame
1 pc.
F.
Back Panel
3 pcs.
M.
Door
1 pc.
Q.
Divider
1 pc.
R.
Back Support
2 pcs.
S.
Side Rack
1 pc.
T.
Side Rack
1 pc.
U.
Base Rack
1 pc.
HARDWARE LIST
Wood Screw
Head Cap Bolt
30 pcs. (+1Extra)
Caster
with and
without lock
4 pcs.
Tools Required For Assembly : Philips screwdriver
Hex Wrench
1 pc.
for Side Drawer Part
(Long 6 x 1” )
16 pcs.(+1 Extra)
Wood Screw
for Bottom Drawer Part
(Short 6 x ½”)
12 pcs.(+1 Extra)
V.
Brush Chrome Pipes
3 pcs.
Machine Screw
for Pull Handle
6 pcs.
Wood Screw
16 pcs. (+ 1 Extra)
W.
Handle Arm
2 pcs.
Wood Plug
7 pcs. (+2 Extra)
Adjustable Pin
16 pcs. (+1 Extra)
X.
Round Arm
1 pc.
Pull Handle
2 pcs.
Pull Handle
2 pcs.
Assembly Instructions 2/5
IMPORTANT NOTE
Do not tighten up all the screws until each part is properly assembled.
You should keep Hex Wrench in the safe place as you may need to
tighten up the Head Cap Bolts in the future.
A
G
Head Cap Bolt
STEP 1
Attach the Lower
Back Stretcher (H)
to the Side Frame (B),
using Head Cap Bolts.
Attach The Back Post (J1),(J2)
to the Lower Back Stretcher (H)
and slide the Back Panels (F) to place.
Attach the Upper Back Stretcher (G) to the assembled unit, using Head Cap Bolts.
Attach the Front Rail (I) to the Side Frame (B) with Head Cap Bolts.
Attach the Side Frame (C) to the assembled unit, tighten up all Head Cap Bolts.
B
F
F
F
I
J1
H
J2
C
STEP 2
Turn the unit in Step1 upside down.
Attach the Middle Frame (D) and (E)
to the unit.
Head Cap Bolt
A
E
J
D
A
STEP 3
Attach 4 Casters to the underside of
the Base (K), put the 2 Casters with
lock in front as you first need to keep
the cart firmly in place. (See sticker in
the bottom indicating front side)
Head Cap Bolt
Assembly Instructions 3/5
Wood Screw
K
Locking Caster
K
STEP 4
Place the Base (K) on the unit.
Tighten up all Head Cap Bolts.
STEP 5
Turn the assembled unit to back its
normal position.
Attach the Divider (Q) in the middle.
Attach the Back Support (R) to the
Upper Back Stretcher (G), using Head
Cap Bolts.
Q
R
Head Cap Bolt
G
R
W
W
Attach the Handle Arm (W) to the
Side Panel (C) with Head Cap Bolts.
Slide the Round Arm (X) into place.
C
A
X
STEP 6
Attach the Side Rack (S) to the Side
Panel (B) with Head Cap Bolts.
Attach the Brush Chrome Pipes(V) and
the Base Rack (U) to the pre-drilled holes
of the Side Rack (S).
Attach the Side Rack (T) to the Side Panel (B).
Assembly
S
U
Instructions
Head Cap Bolt
B
T
V
4/5
STEP 7
Place the Top (A) on the unit.
Tighten up the Head Cap Bolts.
STEP 8
Insert the Adjustable Pins into the Side Panels
and into the Middle Frame at the desired level,
then put the Shelf (N) into the place.
Attach the Pull Handles to the Door (L)
and (M) with Machine Screws.
Attach the Door (L) and (M) to the
Side Panel by sliding the door lift hinges
into the side panel lift hinges.
L
O
N
A
A
Head Cap Bolt
A
P
O
A
M
See assembly instructions for Drawers in
the last page.
Slide the Drawers (P) into place.
STEP 9
Cover all holes with Wood Plugs.
N
Adjustable Pin
Lift hinge
Assembly
Pull Handle
Assembly
Drawer
A
P1
Assembly Instructions 5/5
P3
(Fig)1
P2
MAKE SURE ROLLER
IS ON THE BACK
P4
(Fig) 2
Turn the assembled drawer over and slide the
Plywood Bottom Part (O5) into the grooves
on Side Parts (O3) and (O4). Be sure to push
the plywood all the way forward so it meets the
Front Part (O1).
A
A
P5
P1
P3
(Fig) 3
Insert the remaining (6) 1/2” screws
into the pre-drilled holes in Bottom Part
(O5), then tighten all screws
P4
P2
(Fig)3
(Fig) 1
Line up Side Parts (O3) and (O4) to the Front
Part (O1) and Back Part (O2). Be sure to
follow the Arrow sign sticker on the parts.
Using a Philips screw driver, insert 1” screws
into each of the 4 pre-drilled holes in sides
(O3) and (O4), then tighten half way.
A
P1
P4
(Fig)2
P3
A
P5
* If you are missing any of these
parts, please contact our DMI
Customer Service Department
at 1-877-831-0319 or fax us at
1-800-755-2878.
Unit Part List
P1.
Front Part
2 pcs.
P2.
Back Part
2 pcs.
(Fig) 4
Assemble the Pull Handles
with Machine Screws on
the Front Part (O1).
P3.
Side Part
2 pcs.
P4.
Side Part
2 pcs.
(Fig)4
P5.
Bottom Part
2 pcs.
Loading...