IMPORTANT
Part List
20 05520 0923
Storage Island
B.
Rail
2 pcs.
E.
Bottom
1 pc.
I.
Shelf
3 pcs.
C.
Rail
3 pcs.
F.
Plinth
2 pcs.
J.
Drawer
1 pc.
K.
Drawer
3 pcs.
Refer to later page(s) of these instructions for drawer assembly.
Hardware List
M6x32
Head Cap Bolt
12 pcs. (+1 extra)
M4x16
Machine Screw
8 pcs.
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
Cam Lock
30 pcs. (+6 extra)
Cam Lock Screw
30 pcs. (+2 extra)
Flat Washer
12 pcs. (+1 extra)
Adjustable Pin
12 pcs. (+1 extra)
Spring Washer
12 pcs. (+1 extra)
M3 x.5 32
Wood Screw
4 pcs. (+1 extra)
Cartons 20 05520 0921 and 0922 are also needed for assembly.
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/16” Drill Bit, 3/8” Drill Bit
Handle
4 pcs.
Assembly Instructions 2/8
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
Cam Lock Screw
A
Cam Lock Screw
F
Cam Lock Screw
E
Cam Lock Screw
F
G
H
STEP 1
Insert Cam Lock Screws into pre-drilled holes in Top (A),
Bottom (E), Plinths (F), Side Panels (G) and (H), then tighten.
(See Figure 1)
Cam Lock Screw
Figure 1
Assembly Instructions 3/8
STEP 2
F
STEP 3
Cam Lock
E
Flat Washer
Spring Washer
Head Cap Bolt
F
D
Attach Back Panel (D) to
Bottom (E) with Cam Locks.
(See Figure 2)
Attach Plinths (F) to unit with
Cam Locks.
Figure 2
Wood Screw
B
Attach unit form Step 2 to
Side Panel (H) with Flat Washers,
Spring Washers, Head Cap Bolts
and Cam Locks, tightening bolts
only halfway. (See Figure 3)
Attach Rails (B) and (C) to
unit with Cam Locks and
Wood Screws.
Cam Lock
B
C
C
C
H
Figure 3
Assembly Instructions 4/8
STEP 4
Attach Side Panel (G) to unit with
Cam Locks, Flat Washers, Spring
Washers, Head Cap Bolts and
Wood Screws,
only halfway.
tightening bolts
Wood Screw
G
Turn unit to it’s
upright position.
Adjustable Pin
Cam Lock
Flat Washer
Spring Washer
Head Cap Bolt
STEP 5
I
Insert Adjustable Pins
into side panels at
desired level.
I
Place Shelves (I) into
position.
I
Drawer (J)
Assembly Instructions 5/8
J4
J2
Lock
STEP 7
Slide Drawer Bottom (J5) into groove.
Attach Drawer Front (J1) to unit,
then flip Locks.
J3
STEP 6
Attach Drawer Sides (J3) and (J4) to
Drawer Back (J2), then flip Locks.
(See Figures 4 and 5)
Figure 5Figure 4
J1
J5
Part List
J1.
Drawer Front
1 pc.
Handle
Machine Screw
J2.
Drawer Back
1 pc.
J3.
Drawer Side
1 pc.
Lock
STEP 8
Attach Handle with Machine Screw.
J4.
Drawer Side
1 pc.
J5.
Drawer Bottom
1 pc.
Drawer (K)
K4
Assembly Instructions 6/8
K2
Lock
STEP 10
Slide Drawer Bottom (K5) into groove.
Attach Drawer Front (K1) to unit,
then flip Locks.
K3
STEP 9
Attach Drawer Sides (K3) and (K4) to
Drawer Back (K2), then flip Locks.
K1
K5
Lock
Part List
K1.
Drawer Front
3 pcs.
Handle
Machine Screw
K2.
Drawer Back
3 pcs.
K3.
Drawer Side
3 pcs.
STEP 11
Attach Handle with Machine Screw.
K4.
Drawer Side
3 pcs.
K5.
Drawer Bottom
3 pcs.
Assembly Instructions 7/8
A
Flat Washer
Spring Washer
Head Cap Bolt
Cam Lock
STEP 12
Attach Top (A) to unit with Cam Locks
Flat Washer, Spring Washer and
Head Cap Bolts, tightening bolts
only halfway.
STEP 13
Level unit by adjusting the adjustable
levelers on bottom of unit.
(See Figure 6)
Note: Unit must be level to work
properly.
Slide Drawers (J) and (K) into
position.
J
K
K
K
Figure 6
Assembly Instructions 8/8
Per regulatory requirements, a Tip-over Restraint is included. Follow Step 14 to install it.
STEP 14
Drill a 3/16” hole 1/2” deep 1” below top
of unit in middle of side panel that is
against a wall.
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
3/16” hole drilled in side panel.
Anchor in wall
3/8” wall hole
Bracket
on wall
Wall Screw
3/16” hole in
side panel of unit
Wood Screw
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at drilled hole in
side panel of unit with Wood Screw.
Move unit back into place.
Slide Tip-over Restraint through
Bracket on wall and Bracket on unit.
(See Figure 7)
Put tie end of Tip-over Restraint into lock
end of Tip-over Restraint and pull until tight.
Tie end
Lock end
Bracket
on side panel
of unit
Tip-over
Restraint
Figure 7
Drill 3/8” hole in wall
Side Panel of unit
Hardware List
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tipover Restraint
1 pc. (+1 extra)
M3.5x38
Wall Screw
1 pc. (+1 extra)
M3x16
Wood Screw
1 pc. (+1 extra)
CARE INSTRUCTIONS
NEVER
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
Do not write
directly on surface.
PREVENT
MARKING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
CLEAN
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is underno obligation to provide replacement parts. Parts are not availablefor fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
servicedesk@homestyles-furniture.com,
888-680-7460, 877-831-0319
Loading...