Page 1
20 05436 0912
Storage Island
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Part List
B.
Side Panel
1 pc.
Hardware List
Hex Wrench
1 pc.
C.
Side Panel
1 pc.
Cam Lock Screw
20 pcs. (+2 extra)
M6x32
Head Cap Bolt
12 pcs. (+1 extra)
E.
Shelf
3 pcs.
G.
Rail
2 pcs.
Flat Washer
12 pcs. (+1 extra)
I.
Drawer
1 pc.
J.
Drawer
2 pcs.
Refer to later page(s) of these
instructions for drawer assembly.
Spring Washer
12 pcs. (+1 extra)
Small Hex Wrench
1 pc.
Cam Lock
20 pcs. (+6 extra)
M3.5x32
Wood Screw
4 pcs. (+1 extra)
Adjustable Pin
12 pcs. (+1 extra)
M4x25
Machine Screw
6 pcs.
Carton 20 05436 0911 is also needed for assembly.
Tool(s) required for assembly: Phillips screwdriver, Level, Drill (8 volts or less), 3/16” Drill Bit, 3/8” Drill Bit
Home Styles Customer Service: www.homestyles-furniture.com,
servicedesk@homestyles-furniture.com,
888-680-7460, 877-831-0319
Knob
6 pcs.
Page 2
Assembly Instructions 2/8
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the screws until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
A
Cam Lock Screw
Cam Lock Screw
H
D
B
C
Cam Lock Screw
H
STEP 1
Insert Cam Lock Screws into pre-drilled holes in Top (A), Side Panels (B), (C),
Bottom (D) and Plinths (H), then tighten. (See Figure 1)
Figure 1
Page 3
Assembly Instructions 3/8
STEP 2
Attach Back Panel (F) to Bottom (D) with Cam Locks. (See Figure 2)
Note: Arrow label indicates front of Bottom (D).
D
H
F
Figure 2
Arrow label at front
Cam Lock
Cam Lock
STEP 3
Attach Plinths (H) to unit with Cam Locks.
H
Page 4
Assembly Instructions 4/8
STEP 4
Attach unit to Side Panel (C) with Cam Locks,
Flat Washers, Spring Washers and
Head Cap Bolts, tightening bolts only halfway.
(See Figure 3)
Wood Screw
Attach Rails (G) to unit with Wood Screws,
into pre-drilled holes. (See Figure 4)
Head Cap Bolt
Spring Washer
Flat Washer
Figure 3
Figure 4
G
G
C
Cam Lock
B
Wood Screw
STEP 5
Attach Side Panel (B) to unit with
Cam Locks, Wood Screws, Flat Washers,
Spring Washers and Head Cap Bolts,
tightening bolts only halfway.
Tighten all bolts used in Steps 4 and 5.
Turn unit to its’ upright position.
Cam Lock
Flat Washer
Spring Washer
Head Cap Bolt
Page 5
Drawer (I)
Assembly Instructions 5/8
I4
I2
Lock
STEP 7
Slide Drawer Bottom (I5) into grooves in unit.
Attach Drawer Front (I1) to unit, then flip Locks.
STEP 6
Attach Drawer Sides (I3) and (I4) to
Drawer Back (I2), then flip the Locks.
(See Figures 5 and 6)
I3
Figure 5 Figure 6
I1
Machine Screw
Knob
Part List
I1.
Drawer Front
1 pc.
I2.
Drawer Back
1 pc.
I3.
Drawer Side
1 pc.
I5
Lock
STEP 8
Attach Knobs with Machine Screws.
I4.
Drawer Side
1 pc.
I5.
Drawer Bottom
1 pc.
Page 6
Drawer (J)
J4
Lock
J2
Assembly Instructions 6/8
Attach Drawer Sides (J3) and (J4) to
J3
STEP 9
Drawer Back (J2), then flip Locks.
STEP 10
Slide Drawer Bottom (J5) into grooves in unit.
Attach Drawer Front (J1) to unit, then flip Locks.
Machine Screw
Knob
J1
J5
Lock
STEP 11
Attach Knobs with Machine Screws.
Part List
J1.
Drawer Front
2 pcs.
J2.
Drawer Back
2 pcs.
J3.
Drawer Side
2 pcs.
J4.
Drawer Side
2 pcs.
J5.
Drawer Bottom
2 pcs.
Page 7
Assembly Instructions 7/8
STEP 12
Level unit by adjusting the adjustable
levelers on bottom of unit from Step 5.
(See Figure 7)
Insert Adjustable Pins into side panels
at desired level. (See Figure 8)
Place Shelves (E) into position.
Figure 7
Cam Lock
Figure 8
A
E
E
E
Adjustable Pin
STEP 13
Attach Top (A) to unit with Cam Locks,
Flat Washers, Spring Washers
and Head Cap Bolts, tightening
bolts only halfway.
STEP 14
Slide Drawers (I) and (J) into position.
Tighten all bolts used in this step.
Flat Washer
Spring Washer
Head Cap Bolt
I
J
J
Page 8
Assembly Instructions 8/8
Per regulatory requirements, a Tip-over Restraint is included. Follow Step 15 to install it.
STEP 15
Drill a 3/16” hole 1/2” deep 1” below top
of unit in middle of side panel that is
against a wall.
Place unit at desired location.
Drill a 3/8” hole in wall in-line with
pre-drilled hole at top of unit.
Anchor in wall
3/8” wall hole
Bracket
on wall
Wall Screw
3/16” hole in
side panel of unit
Wood Screw
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
Slide Tip-over Restraint through
Bracket on wall and Bracket on unit.
(See Figure 9)
Put tie end of Tip-over Restraint into lock
end of Tip-over Restraint and pull until tight.
Tie end
Lock end
Bracket at
top of unit
Tip-over
Restraint
Figure 9
Drill 3/8” hole in wall
Side Panel of unit
Hardware List
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tip-over Restraint
1 pc. (+1 extra)
M3.5x40
Wall Screw
1 pc. (+1 extra)
M3.5x16
Wood Screw
1 pc. (+1 extra)
Page 9
CARE INSTRUCTIONS
NEVER
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
Do not write
directly on surface.
PREVENT
MARKING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
CLEAN
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is underno obligationto provide replacement parts. Parts are not availablefor fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or partsmay be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
servicedesk@homestyles-furniture.com,
888-680-7460, 877-831-0319
Loading...