Page 1
20 05170 6512
Buffet
IMPORTANT
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Part List
G.
Bottom
1 pc.
H.
Back Panel
1 pc.
I.
Back Rail
2 pcs.
K.
Door
1 pc.
Hardware List
Cam Lock
18 pcs.(+1 extra)
Cam Lock Screw
18 pcs.(+1 extra)
L.
Door
1 pc.
Magnet
2 pcs.
Adjustable Pin
24 pcs. (+1 extra)
M.
Middle Panel
2 pcs.
J.
Back Rail
1 pc.
N.
Shelf
4 pcs.
M3.5x16
Wood Screw for Magnet
4 pcs. (+1 extra)
M3.5x16
Wood Screw
12 pcs. (+1 extra)
M4x25
Machine Screw
2 pcs.
Knob
2 pcs.
Carton 20 05170 6511 is also needed for assembly.
Tool(s) required for assembly: Phillips screwdriver, Drill (8 volts or less), 3/8” Drill Bit
Home Styles Customer Service: www.homestyles-furniture.com,
servicedesk@homestyles-furniture.com,
888-680-7460, 877-831-0319
Page 2
Assembly Instructions 2/6
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Cam Lock Screw
A
Cam Lock Screw
Cam Lock Screw
STEP 1
Insert Cam Lock Screws into
pre-drilled holes in Top (A),
Side Panels (B), (C) and
Bottom (G), then tighten.
(See Figure 1)
B
Cam Lock Screw
G
STEP 2
Attach Back Rail (I) to Side Panel (B)
with Cam Lock. (See Figure 2)
C
Figure 1
Figure 2
I
B
F
Slide Back Panel (H) into Side Panel (B)
and Back Rail (I).
Attach Back Rail (J) to unit with Cam Lock
and slide Back Panel (F) into place.
Attach Back Rail (I) to unit with
Cam Lock.
Cam Lock
J
H
I
Page 3
Assembly Instructions 3/6
STEP 3
Shelf (E)Attach Magnets to
with Wood Screws for Magnet
into pre-drilled holes.
(See Figure 3)
Figure 3
E
Wood Screw
for Magnet
Magnet
E
C
Cam Lock
STEP 4
Attach Shelf (E) to unit with Cam Locks.
Cam Lock
STEP 5
Attach Side Panel (C) to unit with Cam Locks.
Page 4
Cam Lock
Assembly Instructions 4/6
G
M
M
STEP 6
Attach Middle Panels (M) to unit.
Attach Bottom (G) to unit with Cam Locks.
STEP 7
Attach Top (A) to unit with Cam Locks.
A
Cam Lock
Page 5
Assembly Instructions 5/6
STEP 8
N
K
N
Adjustable Pin
D
D
N
N
L
Machine Screw
Knob
Insert Adjustable Pins into
side panels and middle panels
at desired level.
Place Shelves (D) and (N)
into position.
Attach Doors (K) and (L) to
unit by sliding door hinges
into side panel hinges.
(See Figure 4)
Attach Knobs to Doors (K)
and (L) with Machine Screws.
(See Figure 5)
Figure 4
STEP 9
Level unit by adjusting the adjustable
levelers on bottom of unit. (See Figure 6)
Insert Wood Screws into pre-drilled holes
in unit, then tighten.
Note: Unit must be level before tightening
these screws.
Wood Screw
Figure 5
Figure 6
Page 6
Assembly Instructions 6/6
IMPORTANT
To help reduce the risk of the unit tipping over, the Tip-over Restraint must be installed following these instructions exactly.
STEP 10
Place unit at desired location.
3/8” wall hole
Drill a 3/8” hole in wall in-line with
Pre-drilled hole at top of unit.
Move unit.
Insert Anchor into the wall hole
and attach Bracket with Wall Screw.
Attach Bracket at pre-drilled hole
at top of unit with Wood Screw.
Move unit back into place.
Slide Tip-over Restraint through
Bracket on wall and Bracket on unit.
(See Figure 7)
Put tie end of Tip-over Restraint into lock
end of Tip-over Restraint and pull until tight.
Anchor in wall
Tie end
Lock end
Bracket at
top of unit
Tip-over
Restraint
Bracket
on wall
Wall Screw
Figure 7
Pre-drilled hole
at top of unit
Wood Screw
Hardware List
Anchor
1 pc. (+1 extra)
Bracket
2 pcs. (+1 extra)
Tip-over Restraint
1 pc. (+1 extra)
Drill 3/8” hole in wall
M3.5x40
Wall Screw
1 pc. (+1 extra)
Top of unit
M3.5x16
Wood Screw
1 pc. (+1 extra)
Page 7
CARE INSTRUCTIONS
NEVER
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
Do not write
directly on surface.
PREVENT
MARKING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
CLEAN
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is underno obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
servicedesk@homestyles-furniture.com,
888-680-7460, 877-831-0319
Loading...