Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
Part List
A.
To p
1 pc.
B.
Shelf
1 pc.
C.
Shelf
4 pcs.
F.
Front Rail
1 pc.
G.
Back Rail
1 pc.
H.
Back Rail
1 pc.
K.
Side Frame
1 pc.
L.
Side Frame
1 pc.
D.
Base
1 pc.
E.
Front Rail
1 pc.
I.
Side Panel
2 pcs.
Hardware List
Hex Wrench
1 pc.
Small Hex Wrench
1 pc.
Tool(s) required for assembly: Phillips screwdriver, Level
M6x16
Head Cap Bolt
26 pcs. (+1 extra)
M6x45
Tapered Bolt
2 pcs. (+1 extra)
J.
Middle Panel
1 pc.
Spring Washer
26 pcs. (+1 extra)
M3x12
Wood Screw
24 pcs. (+1 extra)
M.
Upright
1 pc.
Flat Washer
26 pcs. (+1 extra)
Adjustable Pin
16 pcs. (+1 extra)
N.
Panel
2 pcs.
M3.5x30
Wood Screw (long)
1 pc. (+1 extra)
Home Styles Customer Service: www.homestyles-furniture.com,
servicedesk@homestyles-furniture.com,
888-680-7460, 877-831-0319
Assembly Instructions 2/5
IMPORTANT
Use a soft cloth between these parts and the floor.
Make sure unit is level before tightening these screws.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench as the bolts may need to be tightened in the future.
STEP 1
Attach Side Frames (K) and (L) to
Side Panels (I) with Wood Screws.
(See Figure 1)
Figure 1
L
Wood Screw
I
K
I
STEP 2
Figure 2
Figure 3
Attach Front Rails (E), (F) and Back Rails (G), (H) to Side Frame (L)
with Flat Washers, Spring Washers and Head Cap Bolts, tightening
bolts only halfway. (See Figure 2)
Attach Upright (M) to unit with Tapered Bolts, tightening bolts only halfway.
(See Figure 3)
L
G
M
E
H
Head Cap Bolt
Spring Washer
Flat Washer
F
Tapered Bolt
Assembly Instructions 3/5
STEP 3
Attach Shelf (B) to unit.
Attach Base (D) to unit with Flat Washers, Spring Washers and Head Cap Bolts,
tightening bolts only halfway.
B
D
STEP 4
Attach Middle Panel (J) to unit with Wood Screw (long).
Attach Side Frame (K) to unit with Flat Washers,
Spring Washers and Head Cap Bolts, tightening
bolts only halfway.
Tighten all bolts used in
Steps 2, 3 and 4.
Wood Screw (long)
J
Flat Washer
Spring Washer
Head Cap Bolt
Flat Washer
Spring Washer
Head Cap Bolt
K
STEP 5
Turn unit to it’s upright position.
Assembly Instructions 4/5
Attach Panels (N) to unit with Wood Screws.
Wood Screw
STEP 6
N
N
Insert Adjustable Pins into side panels and middle panel at desired level.
(See Figure 4)
Place Shelves (C) into position.
Figure 4
C
C
C
C
Adjustable Pin
Assembly Instructions 5/5
STEP 7
Attach Top (A) to unit with Flat Washers, Spring Washers and Head Cap Bolts,
tightening bolts only halfway.
Tighten all bolts.
A
Flat Washer
Spring Washer
Head Cap Bolt
STEP 8
Level unit by adjusting the adjustable levelers on bottom of unit.
(See Figure 5)
Figure 5
CARE INSTRUCTIONS
NEVER
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
Do not write
directly on surface.
PREVENT
MARKING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
CLEAN
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is underno obligation to provide replacement parts. Parts are not available forfully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at: