Homematic 150007A0 Service Manual

Operating manual
Bedienungsanleitung

Pluggable Switch and Meter p. 2

Schalt-Mess-Steckdose S. 23

HmIP-PSM-UK

Package contents

Quantity Description

1 Homematic IP Pluggable Switch and Meter

1 Operating manual

Documentation © 2016 eQ-3 AG, Germany
All rights reserved. Translation from the original version in Ger­man. This manual may not be reproduced in any format, either in
whole or in part, nor may it be duplicated or edited by electronic,
mechanical or chemical means, without the written consent of
the publisher.
Typographical and printing errors cannot be excluded. However,
the information contained in this manual is reviewed on a regular
basis and any necessary corrections will be implemented in the
next edition. We accept no liability for technical or typographical
errors or the consequences thereof.
All trademarks and industrial property rights are acknowledged.
Printed in Hong Kong
Changes may be made without prior notice as a result of techni­cal advances.

150020 (web)
Version 1.0 (08/2016)

1

A

2

3

Table of contents

1 Information about this manual......................................7

2 Hazard information ..........................................................7

3 Function and device overview .................................... 11

4 General system information ........................................ 11

5 Start-up ............................................................................ 12

5.1 Installation and teaching-in...............................................12

6 Operation ......................................................................... 14

7 Behaviour after power recovery ................................. 14

8 Troubleshooting ............................................................. 15

8.1 Command not confirmed .................................................. 15

8.2 Duty cycle ............................................................................15

8.3 Error codes and flashing sequences ...............................16

9 Restore factory settings ................................................18

10 Maintenance and cleaning ...........................................18

11 General information about radio operation ............. 19

12 Technical specifications ............................................... 20

6

Information about this manual

1 Information about this manual

Please read this manual carefully before beginning op­eration with your Homematic IP components. Keep the
manual so you can refer to it at a later date if you need
to. If you hand over the device to other persons for use,
please hand over this manual as well.

Symbols used:

Attention!

This indicates a hazard.

Note

This section contains important additional infor­mation.

2 Hazard information

We do not assume any liability for damage to
property or personal injury caused by improper
use or the failure to observe the hazard informa
tion. In such cases, any claim under warranty is
extinguished! For consequential damages, we as­sume no liability!

Do not open the device. It does not contain any
parts that can be maintained by the user. There is a
risk of electric shock if the device is opened. In

-

7

Hazard information

the event of an error, please have the device
checked by an expert.

Do not use the device if there are signs of damage
to the housing, control elements or connecting
sockets, for example, or if it demonstrates a mal
function. If you have any doubts, have the device
checked by an expert.

For safety and licensing reasons (CE), unauthor­ized change and/or modification of the device is
not permitted.

The device may only be operated indoors and
must be protected from the eects of moisture,
vibrations, solar or other methods of heat radia
tion, cold and mechanical loads.

The device is not a toy; do not allow children to
play with it. Do not leave packaging material lying
around, plastic films/bags, pieces of polystyrene
etc., can be dangerous in the hands of a child.

Please take the technical data (in particular the
maximum permissible switching capacity of the
relay and the type of load to be connected) into
account before connecting a load! All load data
relates to ohmic loads! Do not exceed the ca

8

-

-

Hazard information

pacity specified for the device. Exceeding this ca­pacity could lead to the destruction of the device,
to a fire or to an electrical accident.

The device may only be connected to an easily ac­cessible power socket outlet. In case of danger,
disconnect the device from the power sock

et out-

let.

Only use the device with properly installed wall
outlets with earth contacts and not with multiple
socket outlets or extension cables.

Do not connect devices to the pluggable switch
and meter which could cause fire or other types of
damage in unattended operation (e.g. irons).

Remove the plug of the connected device from
the pluggable switch and meter, whenever you
make changes or modifications to the device.

Always lay cables in such a way that they do not
become a risk to people and domestic animals.

The device has not been designed to support safe­ty disconnection. The load is not isolated from the
mains.

9

Hazard information

If you use the device in a security application it
has to be operated in connection with an UPS
(uninterruptible power supply) in order to bridge
possible power failure according to EN 50130-4.

Using the device for any purpose other than that
described in this operating manual does not fall
within the scope of intended use and shall invali
date any warranty or liability. This also applies to
any conversion or modification work. The device is
intended f

or private use only.

Do not connect multiple pluggable switches
into one another.

Devices with electronic power supply units (e.g.
TV or high voltage LED light sources) are no ohm­ic loads. They can generate inrush currents with

e than 100 A. S

mor

witching such kind of loads

may lead to premature wear of the actuator.

The device may only be operated within residen­tial buildings.

10

-

Function and device overview

3 Function and device overview

With the Homematic IP Pluggable Switch and Meter you
can comfortably switch on and o connected loads and
meter the corresponding energy consumption as well as
voltage, current and power of the connected devices.
The energy consumption of connected loads and their
energy costs (€/kWh) are displayed via the Homematic IP
app.

The pluggable switch and meter is connected quickly and
without any tools. Simply plug in the device to a socket
and it is immediately ready for use. Thanks to the com­pact design, the pluggable switch and meter does not
block the surrounding sockets.
The device can optionally be used as router to extend the
wireless range.

Device overview (see figure 1):

(A) System button (teaching-in, switching connected

loads on and o, LED)

4 General system information

This device is part of the smart home solution Home­matic IP and works with the HmIP radio protocol. All
Homematic IP devices can be configured comfortably
and individually with a smartphone via the HomematicIP

11

Start-up

app. The available functions provided by the Home­maticIP system in combination with other components
are described in the Homematic IP User Guide. All cur­rent technical documents and updates are provided at
www.eQ-3.de.

5 Start-up

5.1 Installation and teaching-in

Please read this entire section before starting
the teach-in procedure.

First set up your Homematic IP Access Point via
the Homematic IP app to enable operation of
other Homematic IP devices within your system.
For further information, please refer to the oper­ating manual of the Access Point.

To integrate the pluggable switch and meter into your
system and enable it to communicate with other Home­matic IP devices, you must teach-in the device to your
Homematic IP Access Point first.

To teach-in the pluggable switch and meter, please pro­ceed as follows:

• Open the Homematic IP app on your smart­phone.

• Select the menu item “Teach-in device”.

12

Start-up

• Plug in the pluggable switch and meter into the
desired socket (see figure 2).

• Teach-in mode remains activated for 3 minutes.

You can manually start the teach-in mode for an­other 3 minutes by pressing the system button (A)
shortly (see figure 3).

• Your device will automatically appear in the
Homematic IP app.

• To confirm, please enter the last four digits of the
device number (SGTIN) in your app or scan the
QR code. Therefore, please see the sticker sup­plied or attached to the device.

• Please wait until teach-in is completed.

• If teaching-in was successful, the LED lights up

green. The device is now ready for use.

• If the LED lights up red, please try again.

• Select the desired solution for your device.

• In the app, give the device a name and allocate

it to a room.

After teaching-in, connected loads can be easily switched
on and o or the energy consumption can be measured.

13