Home Master HMF1C, HMF2SdgC, HMF2SmgCC, HMF3SdgFeC, HMF3SmgNCC Installation & Service Manual

Customer Service Hotline [phone]-PURE

Page 8

Home Master® Water Filter Owners Manual

MODEL

Maintenance Guide

HMF1C HMF2SdgC HMF2SmgCC HMF3SdgFeC HMF3SmgNCC

ORing122* x x x x x
CFdgd2501-20BB x x x x
CFrfgac20-20BB x x x
Cfre-20BB x
CfKDF85GCC-20BB x x
CFpltn-20BB x

Inspect system for leaks, wear,

& signs of stress

Annually Annually Annually Annually Annually

Inspect oring for damage & de­formaon*

At lter
change

At lter
change

At lter
change

At lter
change

At lter change

Sanize System

At lter
change

At lter
change

At lter
change

At lter
change

At lter change

*It is a good idea to keep a set of spare orings - 1 per housing. You may need to chan ge them each me you
open the housing.

Note: Filter life will vary based upon contaminant level and usage.

Note: protect system against freezing, direct sunlight and the elements

This informaon subject to change without nocaon

Annual Water Consumption

1 person 25,000 gallons

2 people 55,000 gallons

4 people 100,000 gallons

Customer Service Hotline [phone]-PURE

Perfect Water Technologies

Home Master® Water Filter

Installation & Service Manual

HMF1C
HMF2SdgC
HMF2SmgCC
HMF3SdgFeC

HMF3SmgNCC

HMF-CYO

Customer Service Hotline [phone]-PURE

Page 2

Home Master® Water Filter Owners Manual

Contents:

Instruction book: detailed descriptions, photos and troubleshooting guide

Mounting bracket & screws assembled with housing cap(s)
Housing sump(s) with filter(s), o-ring, and silicone grease
Filter housing wrench

Maintenance Schedule

SEE APPENDIX A

General System Specifications (See Appendix A for additional Information)

 Feed water: PSI 20 - 90 PSI ; for pressure greater than 90 PSI install a pressure

regulator set to 75 PSI

 Feed water Tem perature: 40˚ - 100˚(F)
 IRON BACTER IA: NONE

 Yo ur results may vary depending on regular maintenance, general condition of unit, and

initial water supply. Filter not designed to treat microbially unsafe or non-potable water
without adequate disinfection before and after unit.

Customer Service Hotline [phone]-PURE

Page 7

Home Master® Water Filter Owners Manual

Filter Change Instructions

1. For well water—shock chlorinate your well and pipes prior to removing filters.

2. Turn off the water supply to the system. Depress the red pressure release button on the top of
the filter housing cap to relieve system pressure. If your system was not equipped with a
pressure relief valve, leave open a nearby faucet. This will make removing the filter housing
possible.

3. Unscrew the housing (sump) from the cap using the filter wrench included with your system, or
a commercially available “strap” type wrench. Remove and discard old filter cartridge.

4. Scrub the sump and cap with warm water mixed with about 2 tablespoons of household bleach
using a sponge or soft rag. Wear rubber gloves.

5. A) Pour 2 cups of unscented concentrated bleach in each empty sump and close the system to
hand tight and fit snug tight with the wrench. DO NOT over tighten. B) Drain your hot water
heater. C) Open the main water supply to the system. D) Open a faucet at the furthest point
from the system and run water until you smell the chlorine. Flush the toilet. Repeat at each point
of use moving towards the filter system. E) Close the main water supply to the system. F) Open
each housing.

6. Lubricate the o-ring with clean silicon grease . Be sure to use liberal amounts of grease on the
lower oring so that the entire surface is covered. Failure to do so will cause binding, oring
damage, leaks, and difficulties reopening the housing. DO NOT USE PETROLIUM JELLY.
Insert o-ring in grove and press into place taping the o-ring all the way around. Make sure the o­ring is seated level. Replace o-ring if damaged or stretched.

7. Remove filter packaging and insert new filter cartridge into the sump, making sure that it slips
over the standpipe in the bottom of the sump.

8. Fit the bottom of the housing (sump) into the cap and hand tighten, then use the filter wrench to
fit snug. Do not over tighten.

9. Turn on the water supply slowly to allow the system to fill with water. Close any open valves

downstream of the system once water flows and air is purged. Inspect system carefully for
leaks. If a leak is found, first follow the shut off de-pressurization procedure and then remove
the housing to inspect the o-ring to ensure that it is seated properly. Then retighten.

10. Flush the system by turning on a few cold-water faucets. Allow the water to run until the air and

carbon has been purged. Water may be cloudy initially. New activated carbon filter cartridges
may contain loose carbon and air bubbles after installation.