Homelite UT44172 User Manual
OPERATOR’S MANUAL
MANUEL D’UTILISATION
MANUAL DEL OPERADOR
4.8 VOLT GRASS SHEAR
4,8 V CISAILLES À GAZON
4,8 V CIZALLA RECORTADORA DE CESPED
UT44172
Your grass shear has been engineered and manufactured to our high standard for dependability, ease of operation, and
operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using
this product.
Thank you for your purchase.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Ce cisailles à gazon a été conçu et fabriqué conformément à
nos strictes normes de fiabilité, simplicité d’emploi et sécurité
d’utilisation. Correctement entretenu, cet outil vous donnera des
années de fonctionnement robuste et sans problème.
AVERTISSEMENT : Pour réduire les risques de
blessures, l’utilisateur doit lire et veiller à bien comprendre le
manuel d’utilisation avant d’employer ce produit.
Merci de votre achat.
CONSERVER CE MANUEL POUR
FUTURE RÉFÉRENCE
Su cizalla recortadora de cesped ha sido diseñado y fabricado de
conformidad con nuestras estrictas normas para brindar fiabilidad,
facilidad de uso y seguridad para el operador. Con el debido cuidado,
le brindará muchos años de sólido funcionamiento y sin problemas.
ADVERTENCIA: Para reducir el riesgo de lesiones,
el usuario debe leer y comprender el manual del operador antes
de usar este producto.
Le agradecemos su compra.
GUARDE ESTE MANUAL PARA
FUTURAS CONSULTAS
See this fold-out section for all of the figures
referenced in the operator’s manual.
Consulter l’encart à volets afin d’examiner
toutes les figures mentionnées dans le manuel
d’utilisation.
Consulte esta sección desplegable para ver todas
las figuras a las que se hace referencia en el
manual del operador.
ii
Fig. 1
Fig. 3
B
Fig. 5
A
C
B
A
F
E
A - Switch trigger (gâchette, gatillo del
interruptor)
B - Lock-out button (bouton de verrouillage,
botón de seguro de apagado)
C - Sheath (fourreau, funda)
D - Lock-out pin (goupille de verrouillage,
pasador de seguridad)
E - Charger (chargeur, cargador)
F - Blades (lames, hojas)
D
Fig. 2
C
A - Lock-out button (bouton de verrouillage,
botón de seguro de apagado)
B - Switch trigger with padlock (padlock not
included) [gâchette avec cadenas (non
compris), gatillo del interruptor con la
condado (condado no viene incluido)]
C - Switch trigger with lock-out pin (included)
[gâchette avec goupille de verrouillage
(compris), gatillo del interruptor con la
pasador de seguridad (incluido)]
Fig. 4
Fig. 6
B
A
C
A
A - charger input receptacle (prise pour la
alimentation du chargeur , receptáculo para
corriente de entrada del cargador)
PROPER OPERATING POSITION
BONNE POSITION DE TRAVAIL
POSICIÓN CORRECTA PARA EL MANEJO DE
LA HERRAMIENTA
A - Screws (vis, tornillos)
B - Motor housing cover (carter du moteur,
cubierta de la caja del motor)
C - Battery pack (bloc de batteries, paquete de
pilas)
D - Leads (fils, conductores)
E - Wire cutters with rubber coated or insulated
handles (coupe-fils doté d’un revêtement en
caoutchouc ou de poignées isolées, fresas
de alambre con mangos revestidos de hule
o aislados)
Fig. 7
D
A
A - Sheath (fourreau, funda)
B - Blades (lames, hojas)
B
iii
TABLE OF CONTENTS
TABLE DES MATIÈRES / ÍNDICE DE CONTENIDO
Introduction ......................................................................................................................................................................2
Introduction / Introducción
Important Safety Instructions ........................................................................................................................................3-4
Instructions importantes concernant la sécurité / Instrucciones de seguridad importantes
Specific Safety Rules ........................................................................................................................................................ 4
Règles de sécurité concernant le chargeur / Reglas de seguridad para el empleo del cargador
Safety Rules for Charger .................................................................................................................................................. 5
Symboles / Símbolos
Symbols ............................................................................................................................................................................6
Symboles / Símbolos
Features ............................................................................................................................................................................ 7
Caractéristiques / Características
Assembly .......................................................................................................................................................................... 7
Assemblage / Armado
Operation .......................................................................................................................................................................8-9
Utilisation / Funcionamiento
Maintenance ................................................................................................................................................................9-10
Entretien / Mantenimiento
Illustrated Parts List ........................................................................................................................................................ 11
Liste des pièces illustrées / Lista de piezas ilustradas
Warranty .........................................................................................................................................................................12
Garantie / Garantía
Parts Ordering and Service ...............................................................................................................................Back Page
Commande de pièces et réparation / Pedidos de piezas y servicio ......................................................... Page arrière / Pág. posterior
Introduction
Introduction / Introducción
This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability
have been given top priority in the design of this product making it easy to maintain and operate.
* * *
Ce produit offre de nombreuses fonctions destinées à rendre son utilisation plus plaisante et satisfaisante. Lors de la
conception de ce produit, l’accent a été mis sur la sécurité, les performances et la fiabilité, afin d’en faire un outil facile à
utiliser et à entretenir.
* * *
Este producto ofrece numerosas características para hacer más agradable y placentero su uso. En el diseño de este producto
se ha conferido prioridad a la seguridad, el desempeño y la fiabilidad, por lo cual se facilita su manejo y mantenimiento.
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
Read and understand all instructions. When using
electric gardening appliances, basic safety precautions
should always be followed to reduce the risk of fire,
electric shock and personal injury.
read all instructions
For safe operation, read and understand all instructions
before using this product. Be familiar with all controls and
proper use of the machine. Follow all safety instructions.
Failure to follow all safety instructions listed below, can
result in serious personal injury.
Do not allow children or untrained individuals to use this
unit.
Thoroughly inspect the area where the equipment is to
be used and remove all foreign objects.
Use Safety Glasses- Always wear eye protection with
side shields marked to comply with ANSI Z87.1. Failure
to do so could result in objects being thrown into your
eyes, resulting in possible serious injury.
Dress Properly- Wear heavy long pants, long sleeves,
boots, and gloves when working outdoors. Do not wear
loose fitting clothing that could be caught in moving parts,
short pants, sandals or go barefoot. Do not wear jewelry
of any kind. Use of rubber gloves and substantial footwear
is recommended when working outdoors.Secure long
hair above shoulder level to prevent entanglement in
moving parts.
Keep Children Away- Keep all bystanders, children, and
pets at least 50 ft. away.
Stay Alert- Watch what you are doing; use common sense.
Do not operate this unit when you are tired, ill, or under
the influence of alcohol, drugs, or medication.
Do not operate in poor lighting.
Do not operate power tools in explosive atmospheres, such
as in the presence of flammable liquids, gases or dust. Power
tools create sparks which may ignite the dust or fumes.
Avoid body contact with earthed or grounded surfaces
such as pipes, radiators, ranges and refrigerators. There is
an increased risk of electric shock if your body is earthed
or grounded.
Use only with charger listed.
MODEL CHARGER
UT44172 36902252G
Do not overreach- Keep firm footing and balance. Do not
overreach. Overreaching can result in loss of balance or
exposure to hot surfaces.
Keep all parts of your body away from any moving part.
Do not touch or try to stop cutting blades when they are
moving.
Inspect the unit before each use for loose fasteners, etc.
Replace any damaged parts before use.
Store Idle Appliance Indoors- When not in use, product
should be stored indoors in a dry, locked up place—out
of the reach of children. Power tools are dangerous in the
hands of untrained users.
Use only original manufacturer’s replacement parts. Failure
to do so may cause poor performance, possible injury,
and will void your warranty.
Do not, under any circumstance, use any attachment or
accessory on this product which was not provided with
the product or identified as appropriate for use with this
product in the operator’s manual.
Avoid Dangerous Environments- Do not use the product in
damp or wet locations. Do not use in rain. Do not handle
or operate the unit with wet hands.
Use the Right Appliance- Do not use the grass shear for
any job except that for which it is intended.
Do not use on steps, a ladder, or unstable support. Stable
footing on a solid surface enables better control of the
product in unexpected situations.
Do not force appliance- Do not force the grass shear. It
will do the job better and with less likelihood of a risk of
injury at the rate for which it was designed.
DANGER — Keep hands away from cutting area.
Keep hands away from blades. Do not reach underneath
work or around or over the blade while blade is moving.
Do not attempt to remove cut material when blade is
moving. Make sure grass shear is off, blades have stopped
moving, and padlock (not included) or is installed when
clearing jammed materials from blades. Do not grasp the
exposed cutting blades or cutting edges when picking
up or holding the grass shear.
CAUTION — Blade coasts after being turned off.
Inspect extension cords periodically and replace if damaged.
Keep handles dry, clean, and free from oil or grease.
Do not charge in rain or in wet locations.
Always stop the motor, ensure blades have stopped, and
lock switch when not in use by installing padlock (not
included) or the lock-out pin, before attempting to clean
any obstruction caught or jammed in the blade, or before
removing and installing the blade.
Avoid Accidental Starting — Never carry grass shear with
finger on switch. Stop the motor when cutting is delayed
or when walking from one cutting location to another. If the
tool is left unattended, install the padlock (not included)
in the trigger to avoid unauthorized use.
Maintain Grass Shear with Care — Keep cutting edge
sharp and clean for best performance and to reduce
the risk of injury. Follow instructions for lubricating and
changing accessories. Keep handles dry, clean, and free
from oil and grease
Recharge only with the charger specified by the manufacturer.
A charger that is suitable for one type of battery pack may
create a risk of fire when used with another battery pack.
Page 3 — English
IMPORTANT SAFETY INSTRUCTIONS
Under abusive conditions, liquid may leak from the battery,
avoid contact with liquid. If contact accidentally occurs,
flush with water. If liquid contacts eyes, additionally seek
medical help. Liquid leaking from the battery may cause
irritation or burns.
When servicing a power tool, use only identical
replacement parts. Follow instructions in the Maintenance
section of this manual. Use of unauthorized parts or failure
to follow maintenance instructions may create a risk of
shock or injury.
Do not dispose of batteries in a fire. The cells may
explode. Batteries should be recycled. Consult your
local waste authority for information regarding available
recycling and/or disposal options.
SPECIFIC SAFETY RULES
Use non-slip, heavy-duty protective gloves when
operating the grass shear and when installing or removing
blades.
Replace any blade or other parts that are cracked or
damaged. Always make sure blade is installed correctly
and securely fastened before each use. Failure to do
so can cause serious personal injury to the operator,
bystanders, or damage to the unit.
Never cut any material over 3/8 in. diameter.
Maintain a firm grip on handle while cutting with a blade.
Keep the blade away from body.
Know how to stop the unit quickly in an emergency.
Install the padlock (not included) or lock-out pin into
the switch before making any adjustments, performing
maintenance, or storing the grass shear. Such preventive
safety measures reduce the risk of starting the product
accidentally.
Service on the product must be performed by qualified
repair personnel only. Service or maintenance performed
by unqualified personnel could result in injury to the user
or damage to the product.
Always stop motor, install padlock (not included) or the
lock-out pin into hole in switch trigger when not in use,
before attempting to remove any obstruction caught
or jammed in the blade, or before making any blade
adjustments.
Battery powered units do not have to be plugged into an outlet;
therefore, they are always in operating condition. Be aware
of possible hazards even when the unit is not operating.
NEVER attempt to change the cutting blades
Never use grass shear if the switch will not turn the unit
on or off. A unit that cannot be controlled by the switch
is dangerous and must be repaired before use.
Check damaged parts. Before further use of the grass
shear, a guard or other part that is damaged should be
carefully checked to determine that it will operate properly
and perform its intended function. Check for alignment
of moving parts, binding of moving parts, breakage of
parts, mounting, and any other condition that may affect
its operation. A guard or other part that is damaged should
be properly repaired or replaced by an authorized service
center unless indicated elsewhere in this manual.
When replacing batteries, all batteries should be replaced
at the same time. Mixing fresh and discharged batteries
could increase internal cell pressure and rupture the
discharge batteries.
Batteries are not intended to be replaced.
Grass shear is for cutting grass and light weeds only. Do
not use for any other purpose.
Know your power tool. Read operator’s manual carefully.
Learn its applications and limitations, as well as the
specific potential hazards related to this power tool.
Following this rule will reduce the risk of electric shock,
fire, or serious injury.
Battery tools do not have to be plugged into an electrical
outlet; therefore, they are always in operating condition. Be
aware of possible hazards when not using your battery tool
or when changing accessories. Following this rule will reduce
the risk of electric shock, fire, or serious personal injury.
Do not place battery tools or their batteries near fire or heat.
This will reduce the risk of explosion and possibly injury.
Do not crush, drop or damage battery pack. Do not
use a battery pack or charger that has been dropped or
received a sharp blow. A damaged battery is subject to
explosion. Properly dispose of a dropped or damaged
battery immediately.
Batteries can explode in the presence of a source of
ignition, such as a pilot light. To reduce the risk of
serious personal injury, never use any cordless product
in the presence of open flame. An exploded battery can
propel debris and chemicals. If exposed, flush with water
immediately.
For best results, your battery tool should be charged in
a location where the temperature is more than 50°F but
less than 100°F. To reduce the risk of serious personal
injury, do not store outside or in vehicles.
Save these instructions. Refer to them frequently and use
them to instruct others who may use this tool. If you loan
someone this tool, loan them these instructions also to
prevent misuse of the product and possible injury.
Page 4 — English
SAFETY RULES FOR CHARGER
WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below, may result in
electric shock, fire and/or serious personal injury.
Before using battery charger, read all instructions and
cautionary markings in this manual, on battery charger,
battery, and product using battery to prevent misuse of
the products and possible injury or damage.
WARNING:
To reduce the risk of electric shock or damage to
the charger and battery, charge only the UT44172 as
specifically designated on your charger. Other types of
batteries may burst, causing personal injury or damage.
A charger that may be suitable for one type of battery
pack may create a risk of fire when used with another
battery pack.
Do not use charger outdoors or expose to wet or damp
conditions. Water entering charger will increase the risk
of electric shock.
Use of an attachment not recommended or sold by the
battery charger manufacturer may result in a risk of
fire, electric shock, or injury to persons. Following this
rule will reduce the risk of electric shock, fire, or serious
personal injury.
Do not abuse cord or charger. Never use the cord to
carry the charger. Do not pull the charger cord rather than
the plug when disconnecting from receptacle. Damage
to the cord or charger could occur and create an electric
shock hazard. Replace damaged cords immediately.
Make sure cord is located so that it will not be stepped
on, tripped over, come in contact with sharp edges
or moving parts or otherwise subjected to damage or
stress. This will reduce the risk of accidental falls, which
could cause injury, and damage to the cord, which could
result in electric shock.
Keep cord and charger from heat to prevent damage
to housing or internal parts.
Do not let gasoline, oils, petroleum-based products,
etc. come in contact with plastic parts. They contain
chemicals that can damage, weaken, or destroy plastic.
An extension cord should not be used unless absolutely
necessary. Use of improper extension cord could result
in a risk of fire and electric shock. If extension cord must
be used, make sure:
a. That pins on plug of extension cord are the same
number, size and shape as those of plug on charger.
b. That extension cord is properly wired and in good
electrical condition; and
c. That wire size is large enough for AC ampere rating of
charger as specified below:
Cord Length (Feet) 25' 50' 100'
Cord Size (AWG) 16 16 16
NOTE: AWG = American Wire Gauge
Do not operate charger with a damaged cord or plug,
which could cause shorting and electric shock. If damaged,
have the charger replaced by an authorized serviceman.
Do not operate charger if it has received a sharp blow,
been dropped, or otherwise damaged in any way.
Take it to an authorized serviceman for electrical check
to determine if the charger is in good working order.
Do not disassemble charger. Take it to an authorized
serviceman when service or repair is required. Incorrect
reassembly may result in a risk of electric shock or fire.
Unplug charger from outlet before attempting any
maintenance or cleaning to reduce the risk of electric
shock.
Disconnect charger from the power supply when not in
use. This will reduce the risk of electric shock or damage
to the charger if metal items should fall onto the connector.
It also will help prevent damage to the charger during a
power surge.
Disconnect charger from tool when the battery is fully
charged.
Risk of electric shock. Do not touch uninsulated portion
of output connector or uninsulated battery terminal.
For best results, your battery tool should be charged in
a location where the temperature is more than 50° but
less than 100°. To reduce the risk of serious personal
injury, do not store outside or use in vehicles.
Save these instructions. Refer to them frequently and
use them to instruct others who may use this tool. If you
loan someone this tool, loan them these instructions also
to prevent misuse of the product and possible injury.
IMPORTANT SAFETY INSTRUCTIONS
1. SAVE THESE INSTRUCTIONS
This manual contains important safety and operating instructions for battery charger 36901251G.
2. Before using battery charger, read all instructions and cautionary markings on battery charger, battery, and product
using battery.
3. WARNING! To reduce the risk of injury, charge only UT44172. Other types of batteries may burst, causing personal
injury or damage. A charger that may be suitable for one type of battery pack may create a risk of fire when used with
another battery pack.
Page 5 — English
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL MEANING
DANGER:
WARNING:
CAUTION:
CAUTION:
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation
of these symbols will allow you to operate the product better and safer.
SYMBOL NAME EXPLANATION
Safety Alert Symbol Indicates a potential personal injury hazard.
Read Operator’s Manual
Eye Protection
Wet Conditions Alert Do not expose to rain or use in damp locations.
No Hands
Indicates an imminently hazardous situation, which, if not avoided, will result
in death or serious injury.
Indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may result in property
damage.
To reduce the risk of injury, user must read and understand operator’s manual before using this product.
Always wear eye protection with side shields marked to comply
with ANSI Z87.1.
Sharp cutting blades. To prevent serious injury, do not touch
cutting blades.
Risk of Electrocution DANGER! Risk of electrocution!
Electric Shock
Keep Bystanders Away Keep all bystanders at least 50 ft. away.
Gloves
Hot Surface
Recycle Symbol
V
A
Hz
W
hrs
Volts Voltage
Amperes Current
Hertz Frequency (cycles per second)
Watt Power
Hours Time
Class II Construction Double-insulated construction
Failure to use in dry conditions and to observe safe practices
can result in electric shock.
Wear non-slip, heavy-duty protective gloves when handling
the blades.
To reduce the risk of injury or damage, avoid contact with any
hot surface.
This product uses nickel- cadmium (Ni-Cd) batteries. Local, state,
or federal laws may prohibit disposal of batteries in ordinary
trash. Consult your local waste authority for information regarding
available recycling and/or disposal options.
Page 6 — English
FEATURES
FEATURES
PRODUCT SPECIFICATIONS
Cutting Capacity........................................................ 3/8 in.
Total Blade Length........................................................ 4 in.
Motor .....................................................................4.8 V DC
Charger Input.....................................120 V, AC only, 60 Hz
Weight ..................................................................... 2.1 lbs.
KNOW YOUR GRASS SHEAR
See Figure 1.
The safe use of this product requires an understanding of the
information on the product and in this operator’s manual as
well as a knowledge of the project you are attempting. Before
use of this product, familiarize yourself with all operating
features and safety rules.
CHARGER
The grass shear comes with a convenient portable
charger.
LOCK-OUT BUTTON
The lock-out button reduces the possibility of accidental
starting.
LOCK-OUT PIN
The lock-out pin is inserted into the switch trigger when
removing cut or jammed material from the blades and when
performing any maintenance.
ASSEMBLY
PADLOCK (OPTIONAL, NOT INCLUDED WITH
GRASS SHEAR)
An optional padlock (with a long shackle up to 9/32 in.
diameter) may be used. The padlock is inserted into the
switch trigger when installing, removing, changing the blades,
when removing cut or jammed material from the blades, when
performing any maintenance, and for storage.
NOTE: Only a locked padlock with the key stored in another
location can prevent unauthorized use of the grass shear.
SHEATH
The sheath keeps the operator from coming in contact with
the sharp blades when the tool is not in use. It also helps
keep the blades from being nicked or damaged when the
tool is in storage.
SWITCH TRIGGER
The switch trigger activates the motor and blades when it is
depressed and the lock-out button is pushed.
UNPACKING
This product has been shipped completely assembled.
Carefully remove the product and any accessories from
the box. Make sure that all items listed in the packing list
are included.
WARNING:
Do not use this product if it is not completely assembled
or if any parts appear to be missing or damaged. Use of
a product that is not properly and completely assembled
could result in serious personal injury.
Inspect the product carefully to make sure no breakage
or damage occurred during shipping.
Do not discard the packing material until you have
carefully inspected and satisfactorily operated the
product.
If any parts are damaged or missing, please call
1-800-242-4672 for assistance.
PACKING LIST
Grass Shear with Internal Battery
Charger
Sheath
Operator’s Manual
WARNING:
If any parts are damaged or missing do not operate this
product until the parts are replaced. Use of this product
with damaged or missing parts could result in serious
personal injury.
WARNING:
Do not attempt to modify this product or create
accessories not recommended for use with this product.
Any such alteration or modification is misuse and could
result in a hazardous condition leading to possible serious
personal injury.
Page 7 — English
OPERATION
WARNING:
Do not allow familiarity with product to make you careless.
Remember that a careless fraction of a second is
sufficient to inflict serious injury.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes, resulting in possible
serious injury.
WARNING:
Do not use any attachments or accessories not
recommended by the manufacturer of this product. The use of
attachments or accessories not recommended can result
in serious personal injury.
APPLICATIONS
You may use this product for the purpose listed below:
Trimming grass and other light weeds
CHARGING THE GRASS SHEAR
See Figure 2.
This tool has been shipped in a low charge condition to prevent
possible problems. Therefore, you should charge it overnight
prior to use. After each use, charge for at least 8 hours.
To charge:
Stop the motor.
Install padlock (not included) or lock-out pin into switch
trigger hole. Keep both hands away from switch.
Insert charger plug into input jack making sure they are
properly connected.
Charger can be used with normal household voltage
of 120 volts, AC only, 60 Hz.
Connect charger to power supply.
Do not place charger in an area of extreme heat or cold.
It will work best at normal room temperature.
LOCK-OUT BUTTON
See Figure 3.
The lock-out button reduces the possibility of accidental
starting. The lock-out button is located on the handle above
the switch trigger. The lock-out button must be depressed
before you pull the switch trigger. The lock-out button resets
each time the switch trigger is released.
Page 8 — English
SWITCH TRIGGER
See Figure 3.
To prevent unauthorized use or accidental starting of the
grass shear, disconnect it from the charger and lock the
switch in the off position. To lock the switch, install a padlock (not included) or lock-out pin through the hole in the
switch trigger. A padlock with a long shackle up to 9/32 in.
diameter may be used. When the padlock is installed and
locked, the switch is inoperable. Store the padlock key in
another location.
NOTE: The lock-out pin does not protect against unauthorized
usage. Only a locked padlock with the key stored in another
location can prevent unauthorized use of the grass shear.
STARTING AND STOPPING
See Figure 3.
To start:
Remove padlock (not provided) or lock-out pin from
switch trigger.
Depress the lock-out button.
Depress the switch trigger.
To stop:
Release the switch trigger.
Install padlock (not provided) or lock-out pin.
CUTTING TIPS
See Figures 4.
DANGER:
Never cut near electric cords or lines. If blade jams on
any electrical cord or line, DO NOT TOUCH THE BLADE!
IT CAN BECOME ELECTRICALLY LIVE AND VERY
DANGEROUS. Continue to hold the grass shear by the
handle or lay it down and away from you in a safe manner.
Disconnect the electrical service to the damaged line or
cord before attempting to free the blade from the line or
cord. Contact with the blade, other conductive parts of
the grass shear, or live electric cords or lines will result in
death by electrocution or serious injury.
WARNING:
Clear the area to be cut before each use. Remove all
objects such as cords, lights, wire, or loose string which
can become entangled in the cutting blade and create a
risk of serious personal injury.
Do not force the grass shear through heavy grass. This
can cause the blades to bind and slow down. If the blades
slow down, reduce the pace.
If blades do become jammed, stop the motor, allow the
blades to stop, and install padlock (not included) or lock-out
pin into switch trigger hole before attempting to remove
the obstruction.
OPERATION
OPERATING THE GRASS SHEAR
WARNING:
Read the safety information for safe operation using the
blade. Extreme care must be taken when using blades
to ensure safe operation. Refer to Important Safety
Instructions and Specific Safety Rules.
MAINTENANCE
WARNING:
When servicing, use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
WARNING:
Always wear eye protection with side shields marked to
comply with ANSI Z87.1. Failure to do so could result in
objects being thrown into your eyes, resulting in possible
serious injury.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline, petroleumbased products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken, or
destroy plastic which may result in serious personal
injury.
Only the parts shown on the parts list are intended to be
repaired or replaced by the customer. All other parts should
be replaced at an Authorized Service Center.
WARNING:
Blades are sharp. When handling the blade assembly,
wear non-slip, heavy-duty protective gloves. Do not place
your hand or fingers between blades or in any position
where they could get pinched or cut. NEVER touch blades
or service unit while running.
Inspect and clear the area of any hidden objects.
Never use the grass shear near power lines, fencing, posts,
buildings, or other immovable objects.
Never use a blade after hitting a hard object without first
inspecting it for damage. Do not use if any damage is
detected.
LUBRICATING THE BLADE
See Figure 5.
For easier operation and longer blade life, lubricate blades
before and after each use. If you will be using the grass
shear for an extended period, it is advisable to oil the blade
during use.
Stop the motor and allow blades to stop moving.
Install padlock (not included) or lock-out pin into switch
trigger hole. Keep both hands away from switch.
Lay the grass shear on a flat surface. Apply light weight
machine oil along the edge of the top blade.
Remove padlock or lock-out pin from switch trigger hole.
NOTE: Do not oil while the grass shear is running.
CLEANING THE GRASS SHEAR
Stop the motor and allow blades to stop moving.
Install padlock (not included) or lock-out pin into switch
trigger hole. Keep both hands away from switch.
Slide the sheath over the blade.
Clean dirt and debris from the body of the grass shear,
using a damp cloth with a mild detergent.
Remove padlock or lock-out pin from switch trigger hole.
NOTE: Do not use any strong detergents on the plastic
housing or the handle. They can be damaged by certain
aromatic oils such as pine and lemon, and by solvents
such as kerosene.
BATTERIES
This product is equipped with a nickel-cadmium rechargeable battery. Length of service from each charging will depend on the type of work you are doing.
The battery in this product has been designed to provide
maximum trouble-free life. However, like all batteries, it will
eventually wear out.
To obtain the longest possible battery life, we suggest
removing the product from the charger once it is fully
charged and ready for use.
NOTE: Batteries are not intended to be replaced.
Page 9 — English
MAINTENANCE
BATTERY PACK REMOVAL AND PREPARATION
FOR RECYCLING
See Figure 6.
Stop the motor.
Install padlock (not included) or lock-out pin into switch
trigger hole. Keep both hands away from switch.
Remove the screws securing motor housing cover, then
remove cover.
Lift batteries from motor housing enough to expose leads
and battery terminals.
Using wire cutters with rubber coated or insulated
handles, clip the battery leads and remove the battery
for disposal.
Remove padlock or lock-out pin from switch trigger hole.
To preserve natural resources, please recycle or dispose of
batteries properly.
This product contains nickel-cadmium
batteries. Local, state or federal laws
may prohibit disposal of batteries in
ordinary trash.
Consult your local waste authority for
information regarding available recycling
and/or disposal options.
WARNING:
Upon removal, cover the battery pack’s terminals with
heavy-duty adhesive tape. Do not attempt to destroy
or disassemble battery pack or remove any of its
components. Nickel-cadmium batteries must be recycled
or disposed of properly. Also, never touch both terminals
with metal objects and/or body parts as short circuit may
result. Keep away from children. Failure to comply with
these warnings could result in fire and/or serious injury.
STORING THE GRASS SHEAR
See Figure 7.
Install padlock (not included) or lock-out pin into switch
trigger hole.
NOTE: Only a locked padlock with the key stored in an-
other location can prevent unauthorized use of the grass
shear.
Clean all foreign material from the grass shear. Store
indoors in a dry, locked up place—out of the reach of
children. Keep away from corrosive agents such as garden
chemicals and de-icing salts.
Always place the sheath on the cutting blades before
transporting or storing the unit.
Store the product where the temperature is below 80°F.
Store the product in a “discharged” condition.
NOTE: The lock-out pin does not protect against unauthorized
usage. Only a locked padlock with the key stored in another
location can prevent unauthorized use of the grass shear.
Page 10 — English
Loading...