Page 1
OPERATOR’S MANUAL
26cc Hedge Trimmer
UT40502 /UT40903
(ALL VERSIONS)
Your hedge trimmer has been engineered and manufactured to our high standard for dependability, ease of operation, and
operator safety. Properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using
this product.
Thank you for your purchase.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Page 2
TABLE OF CONTENTS
Introduction ...................................................................................................................................................................... 2
General Safety Rules ........................................................................................................................................................ 3
Specific Safety Rules ....................................................................................................................................................... 4
Symbols ........................................................................................................................................................................5-6
Features ............................................................................................................................................................................7
Assembly ..........................................................................................................................................................................8
Operation .....................................................................................................................................................................8-10
Maintenance ..............................................................................................................................................................11-13
Troubleshooting ..............................................................................................................................................................14
Warranty ....................................................................................................................................................................15-17
Parts Ordering / Service ....................................................................................................................................Back Page
INTRODUCTION
This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability
have been given top priority in the design of this product making it easy to maintain and operate.
Page 2
Page 3
GENERAL SAFETY RULES
WARNING:
Read and understand all instructions. Failure to follow
all instructions listed below may result in electric shock,
fire, and/or serious personal injury.
READ ALL INSTRUCTIONS
For safe operation, read and understand all instructions
before using this product. Be familiar with all controls and
proper use of the machine. Follow all safety instructions.
Failure to follow all safety instructions listed below, can
result in serious personal injury.
Do not allow children or untrained individuals to use this
unit.
Never start or run the engine in a closed or poorly venti-
lated area; breathing exhaust fumes can kill.
Thoroughly inspect the area where the equipment is to
be used and remove all foreign objects.
Wear safety glasses or goggles that are marked to comply
with ANSI Z87.1 standard and hearing protection when
operating this product.
To reduce the risk of hearing loss associated with sound
level(s), hearing protection is required.
Always be aware of your surroundings and stay alert for
possible hazards that you may not hear due to the noise
of the machine.
Wear heavy, long pants, boots, and gloves. Do not wear
loose fitting clothing, short pants, or go barefoot. Do not
wear jewelry of any kind.
Product users on United States Forest Service land, and
in some states, must comply with fire prevention regulations. This product is equipped with a spark arrestor;
however, other user requirements may apply. Check with
your federal, state, or local authorities.
Secure long hair above shoulder level to prevent entan-
glement in moving parts.
Keep all bystanders, children, and pets at least 50 ft. away.
Do not operate this unit when you are tired, ill, or under
the influence of alcohol, drugs, or medication.
Do not operate in poor lighting.
Keep firm footing and balance. Do not overreach. Over-
reaching can result in loss of balance or exposure to hot
surfaces.
Keep all parts of your body away from any moving part.
Do not touch area around the muffler or cylinder of the
unit; these parts get hot from operation.
Always stop the engine and remove the spark plug wire
before making any adjustments or repairs except for
carburetor adjustments.
Inspect the unit before each use for loose fasteners, fuel
leaks, etc. Replace any damaged parts before use.
It has been reported that vibrations from hand-held tools
may contribute to a condition called Raynaud’s Syndrome
in certain individuals. Symptoms may include tingling,
numbness, and blanching of the fingers, usually apparent
upon exposure to cold. Hereditary factors, exposure to
cold and dampness, diet, smoking, and work practices
are all thought to contribute to the development of these
symptoms. It is presently unknown what, if any, vibrations
or extent of exposure may contribute to the condition.
There are measures that can be taken by the operator to
possibly reduce the effects of vibration:
a) Keep your body warm in cold weather. When operating
the unit wear gloves to keep your hands and wrists
warm. It is reported that cold weather is a major factor
contributing to Raynaud’s Syndrome.
b) After each period of operation, exercise to
increase blood circulation.
c) Take frequent work breaks. Limit the amount of
exposure per day.
d) Keep the product well maintained, fasteners
tightened and worn parts replaced.
If you experience any of the symptoms of this condition,
immediately discontinue use and see your physician about
these symptoms.
Mix and store fuel in a container approved for gasoline.
Mix fuel outdoors where there are no sparks or flames.
Wipe up any fuel spillage. Move 30 ft. away from refueling
site before starting engine.
Stop the engine and allow to cool before refueling or
storing the unit.
Allow the engine to cool; empty the fuel tank and secure
the unit from moving before transporting in a vehicle.
Use only original manufacturer’s replacement parts. Failure
to do so may cause poor performance, possible injury,
and will void your warranty.
Do not, under any circumstance, use any attachment or
accessory on this product, which was not provided with
the product, or identified as appropriate for use with this
product in the operator’s manual.
Avoid dangerous environments. Do not use the attach-
ment in damp or wet locations. Do not use in rain.
Do not use on steps, a ladder, or unstable support. Stable
footing on a solid surface enables better control of the
tool in unexpected situations.
Do not force the hedge trimmer. It will do the job better
and with less likelihood of a risk of injury at the rate for
which it was designed.
Keep hands away from cutting area. Keep hands away
from blades. Do not reach underneath work or around
or over the blade while blade is rotating. Do not attempt
to remove cut material when blade is moving.
Blade coasts after being turned off.
Page 3
Page 4
SPECIFIC SAFETY RULES
Use heavy gloves when operating the hedge trimmer and
when installing or removing blades.
Always stop the engine and remove the spark plug wire
before attempting to remove any obstruction caught or
jammed in the blade or before removing and installing
the blade.
Replace any blade that has been damaged. Always make
sure blade is installed correctly and securely fastened before each use. Failure to do so can cause serious injury.
Never cut any material over 3/8 in. diameter.
Maintain a firm grip on both handles while cutting with a
blade. Keep the blade away from body.
Know how to stop the unit quickly in an emergency.
Do not use trimmer without front handles in place. Keep
both hands on handles when the unit is in use.
To avoid accidental starting, never carry the unit with the
engine running.
Save these instructions. Refer to them frequently and use
them to instruct others who may use this tool. If you loan
someone this tool, loan them these instructions also to
prevent misuse of the product and possible injury.
Page 4
Page 5
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper
interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL NAME EXPLANATION
Safety Alert Symbol Precautions that involve your safety.
Read the Operator’s Manual
Eye, Hearing and Head
Protection
Keep Bystanders Away Keep all bystanders at least 50 ft. away.
Hot Surface
Operate With Two Hands
Sharp Blade
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Wear eye protection which is marked to comply with ANSI
Z87.1 as well as hearing protection when operating this
equipment.
To reduce the risk of injury or damage, avoid contact with
any hot surface.
Hold and operate the hedge trimmer properly with both
hands.
Do not install or use any type of blade on a product displaying this symbol.
Risk of Electrocution DANGER! Risk of electrocution!
Gasoline and Lubricant
Use unleaded gasoline intended for motor vehicle use with
an octane rating of 87 [(R + M) / 2] or higher. This product is
powered by a 2-cycle engine and requires pre-mixing gasoline
and 2-cycle lubricant.
Page 5
Page 6
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL MEANING
DANGER:
WARNING:
CAUTION:
CAUTION:
Indicates an imminently hazardous situation, which, if not avoided, will result
in death or serious injury.
Indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may result in property
damage.
SERVICE
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to your nearest
AUTHORIZED SERVICE CENTER for repair. When servicing, use only identical replacement parts.
WARNING:
To avoid serious personal injury, do not attempt to use this
product until you read thoroughly and understand completely the operator’s manual. If you do not understand
the warnings and instructions in the operator’s manual,
do not use this product. Call Homelite customer service
for assistance.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles or
safety glasses with side shields and, when needed, a full face shield. We recommend Wide Vision Safety
Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye protection
which is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
Page 6
Page 7
FEATURES
FEATURES
PRODUCT SPECIFICATIONS
Cutting Capacity........................................................................................................................................................... 3/8 in.
Total Blade Length..........................................................................................................................................................20 in.
Fuel Tank Capacity ........................................................................................................................................................10 oz.
Power ...........................................................................................................................................................................0.8 HP
Cutting Strokes Per Minute ................................................................................................................................... 1500-1600
Weight .......................................................................................................................................................................10.5 lbs.
scabbaRd
sTaRTER
GRIp
GuaRd
fRonT
handlE
chokE dIal
bladEs
on/off
swITch
TRIGGER
lock
ThRoTTlE
lock
REaR
handlE
TRIGGER
Fig. 1
KNOW YOUR HEDGE TRIMMER
See Figure 1.
The safe use of this product requires an understanding of
the information on the tool and in this operator’s manual as
well as a knowledge of the project you are attempting. Before
use of this product, familiarize yourself with all operating
features and safety rules.
GUARD
The guard helps to deflect chips or other debris away from
the operator’s hands.
SCABBARD
The scabbard keeps the operator from coming in contact
with the sharp blades when the tool is not in use. It also
helps keep the blades from being nicked or damaged when
the tool is in storage.
THROTTLE LOCK
The throttle lock allows you to start the hedge trimmer without having to continuously hold the throttle trigger.
TRIGGER LOCK
The trigger lock prevents unintentional starting of the hedge
trimmer blades.
Page 7
Page 8
ASSEMBLY
UNPACKING
This product has been shipped completely assembled.
Carefully remove the product and any accessories from
the box. Make sure that all items listed in the packing list
are included.
Inspect the product carefully to make sure no breakage
or damage occurred during shipping.
Do not discard the packing material until you have care-
fully inspected and satisfactorily operated the product.
If any parts are damaged or missing, please call
1-800-242-4672 for assistance.
PACKING LIST
Hedge Trimmer
Scabbard
2-Cycle Engine Lubricant
Operator’s Manual
WARNING:
If any parts are damaged or missing, do not operate this
product until the parts are replaced. Failure to heed this
warning could result in serious personal injury.
WARNING:
Do not attempt to modify this product or create accessories not recommended for use with this product. Any
such alteration or modification is misuse and could result
in a hazardous condition leading to possible serious
personal injury.
WARNING:
To prevent accidental starting that could cause serious
personal injury, always disconnect the engine spark plug
wire from the spark plug when assembling parts.
OPERATION
WARNING:
Do not allow familiarity with this product to make you
careless. Remember that a careless fraction of a second is
sufficient to inflict serious injury.
WARNING:
Always wear safety goggles or safety glasses with side
shields when operating power tools. Failure to do so could
result in objects being thrown into your eyes, resulting in
possible serious injury.
WARNING:
Do not use any attachments or accessories not recommended by the manufacturer of this product. The use of
attachments or accessories not recommended can result
in serious personal injury.
APPLICATIONS
You may use this product for the purposes listed below:
Trimming and shaping hedges and shrubbery
FUELING AND REFUELING THE TRIMMER
FUEL MIXTURE
This product is powered by a 2-cycle engine and requires
pre-mixing gasoline and 2-cycle lubricant. Pre-mix unleaded
gasoline and 2-cycle engine lubricant in a clean 1 gallon
container approved for gasoline.
Recommended fuel: This engine is certified to operate on
unleaded gasoline intended for automotive use.
Mix Homelite Premium Exact Mix lubricant with gasoline
according to the instructions on the package. If Premium Ex-
act Mix lubricant is not available, use a high quality synthetic
2-cycle engine lubricant, mixed at 2.6 oz. per gallon (US).
Do not use automotive lubricant or 2-cycle outboard lubricant.
NOTE: Premium Exact Mix fuel mix will stay fresh up to
30 days. DO NOT mix quantities larger than usable in a 30
day period.
PREMIUM EXACT MIX (50:1)
GASOLINE LUBRICANT
1 gallon (US) 2.6 oz.
1 Liter 20 cc (20 ml)
Page 8
Page 9
OPERATION
FILLING TANK
Position the hedge trimmer on its side with the fuel cap
pointing upward.
Clean surface around fuel cap to prevent contamination.
Loosen fuel cap slowly. Rest the cap on a clean surface.
Carefully pour fuel into the tank. Avoid spillage.
Immediately replace fuel cap and hand tighten. Wipe up
any fuel spillage.
NOTE: It is normal for smoke to be emitted from a new engine
after first use.
Fig. 2
WARNING:
Always shut off engine before fueling. Never add fuel to a
machine with a running or hot engine. Move at least 30 ft.
from refueling site before starting engine. Do not smoke!
STARTING AND STOPPING
See Figures 2 - 4.
The starting method differs depending on whether the engine
is cold or warm.
Place the hedge trimmer on level ground and ensure that
no objects or obstructions are in the immediate vicinity
that could come in contact with the blades.
Hold the front handle firmly with your left hand and put
your right foot onto the base of the rear handle.
To start a cold engine:
Place the on/off switch in the ON position.
Slowly press the primer bulb seven (7) times.
Rotate the choke dial clockwise to the FULL CHOKE
position.
While squeezing both the trigger lock and throttle trigger,
push in the throttle lock button. Release the throttle trigger.
This latches the trigger for starting.
pRIMER
bulb
ThRoTTlE
ThRoTTlE
TRIGGER
on/off
swITch
lock
TRIGGER
lock
Fig. 3
WARNING:
When the engine starts with the trigger locked, the blades
will move. Keep body, objects, and obstructions away from
blades. Failure to keep away from the blades can result
in serious injury.
Pull the starter grip sharply until engine attempts to run
(no more than 4 pulls).
Rotate the choke dial to the counterclockwise HALF
CHOKE position.
Pull the starter grip sharply until the engine runs.
Allow the engine to run for 10 seconds.
Rotate the choke dial counterclockwise to the RUN
position.
Squeeze the trigger to disengage the throttle lock and
return the engine to idle.
Run
half
chokE
full
chokE
Fig. 4
Page 9
Page 10
OPERATION
To start a warm engine:
Slowly press the primer bulb seven (7) times.
Pull the starter grip sharply until the engine runs.
TO STOP THE ENGINE:
See Figure 3.
Release the throttle trigger and push STOP on the ON/OFF
switch.
IF ASSISTANCE IS REqUIRED STARTING
THIS PRODUCT:
Do not return this product to the retail store where it was
purchased. Please call our Customer Service Department
for any issues you may have.
For Help Call: 1-800-242-4672
CUTTING TIPS
See Figures 5 - 6.
WARNING:
Always keep both hands on the hedge trimmer handles.
Never hold shrubs with one hand and operate hedge trimmer with the other. Failure to heed this warning can result
in serious injury.
Fig. 5
WARNING:
Clear the area to be cut before each use. Remove all
objects such as cords, lights, wire, or loose string which
can become entangled in the cutting blade and create a
risk of serious personal injury.
Do not force the hedge trimmer through heavy shrubbery.
This can cause the blades to bind and slow down. If the
blades slow down, reduce the pace.
Do not attempt to cut stems or twigs that are larger than
3/8 in. thick, or those obviously too large to feed into the
cutting blade. Use a non-powered hand saw or pruning
saw to trim large stems.
If blades do become jammed, stop the engine, allow the
blades to stop, and remove the obstruction.
If desired, you can use a string to help cut your hedge
level. Decide how high you want the hedge. Stretch a piece
of string along the hedge at the desired height. Trim the
hedge just above the guide line of string. Trim the side of
a hedge so that it will be slightly narrower at the top. More
of the hedge will be exposed when shaped this way, and
it will be more uniform.
Always wear gloves when using the hedge trimmer. When
trimming new growth, use a wide sweeping action, so that
the stems are fed directly into the cutting blade. Older
growth will have thicker stems and will be trimmed easiest
by using a sawing movement.
Fig. 6
OPERATING THE HEDGE TRIMMER
WARNING:
Read the safety information for safe operation using the
blade. Extreme care must be taken when using blades to
ensure safe operation. Refer to Specific Safety Rules.
Always hold hedge trimmer with both hands when operat-
ing. Use a firm grip on the handles. The unit is used for
cutting in either direction in a slow, sweeping action from
side to side.
The hedge trimmer should be positioned so that your body
will not come into contact with the muffler on the power
head. Stand so that you are stable and balanced on both
feet.
Inspect and clear the area of any hidden objects.
Never use the hedge trimmer near power lines, fencing,
posts, buildings, or other immovable objects.
Never use a blade after hitting a hard object without first
inspecting it for damage. Do not use if any damage is
detected.
Page 10
Page 11
MAINTENANCE
WARNING:
When servicing, use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
WARNING:
Always wear safety goggles or safety glasses with side
shields during product operation. If operation is dusty,
also wear a dust mask.
WARNING:
Before inspecting, cleaning, or servicing the machine,
shut off engine, wait for all moving parts to stop, and
disconnect spark plug wire and move it away from spark
plug. Failure to follow these instructions can result in
serious personal injury or property damage.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, lubricant, grease, etc.
REPLACING BLADES
See Figure 7.
Periodically inspect the blades for damage and wear. Always
use the manufacturer’s specified replacement blades.
Stop the engine and disconnect the spark plug wire.
Place the hedge trimmer upside down on a workbench
and remove the gear box cover screws.
Remove the gear box cover and set aside.
Remove the blade screws.
Remove the old blade.
Install the new blade and reinstall blade screws to
secure.
Install the gear box cover and reinstall gear box cover
screws to secure.
bladE
scREws
GEaR boX
coVER
scREws
GEaR boX
coVER
WARNING:
Do not at any time let brake fluids, gasoline, petroleumbased products, penetrating lubricants, etc., come in contact with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.
Only the parts shown on the parts list are intended to be
repaired or replaced by the customer. All other parts should
be replaced at an Authorized Service Center.
WARNING:
Blades are sharp. When handling the blade assembly,
wear non-slip, heavy-duty protective gloves. Do not place
your hand or fingers between blades or in any position
where they could get pinched or cut. NEVER touch blades
or service unit with the spark plug wire connected.
bushInG
GEaR
Fig. 7
Page 11
Page 12
MAINTENANCE
LUBRICATING THE BLADE
See Figure 8.
For easier operation and longer blade life, lubricate the hedge
trimmer blade before and after each use.
Stop the engine and disconnect the spark plug wire.
Lay the hedge trimmer on a flat surface. Apply light weight
machine lubricant along the edge of the top blade.
If you will be using the hedge trimmer for an extended period,
it is advisable to lubricant the blade during use.
NOTE: Do not lubricate while the hedge trimmer is run-
ning.
Stop the engine and disconnect the spark plug wire.
Lubricate the hedge trimmer as described above.
Reconnect the spark plug wire and resume use.
CLEANING THE HEDGE TRIMMER
Stop the engine and disconnect the spark plug wire.
Slide the scabbard over the blade.
Clean dirt and debris from the body of the hedge trimmer,
using a damp cloth with a mild detergent.
NOTE: Do not use any strong detergents on the plastic
housing or the handle. They can be damaged by certain
aromatic lubricants such as pine and lemon, and by solvents such as kerosene.
Fig. 8
chokE dIal
coVER
waVy
washER
CLEANING THE AIR FILTER SCREEN
See Figures 9 - 10.
For proper performance and long life, keep the air filter
screen clean.
Remove the hex nut, wavy washer, flat washer, and choke
dial cover.
Brush the air filter screen lightly to clean.
Reinstall the choke dial cover, flat washer, wavy washer,
and hex nut.
FUEL CAP
WARNING:
A leaking fuel cap is a fire hazard and must be replaced
immediately.
The fuel cap contains a non-serviceable filter and a check
valve. A clogged fuel filter will cause poor engine performance. If performance improves when the fuel cap is loosened, check valve may be faulty or filter clogged. Replace
fuel cap if required.
hEX
nuT
bRush
flaT
washER
fIlTER
scREEn
Fig. 9
fIlTER
scREEn
Fig. 10
Page 12
Page 13
MAINTENANCE
SPARK PLUG
This engine uses a Champion RCJ6Y or equivalent spark
plug with .025 in. electrode gap. Use an exact replacement
and replace annually, or more frequently if necessary.
CLEANING THE EXHAUST PORT AND
MUFFLER
Depending on the type of fuel used, the type and amount of
lubricant used, and/or your operating conditions, the exhaust
port and muffler may become blocked with carbon deposits.
If you notice a power loss with your gas powered tool, you
may need to remove these deposits to restore performance.
We highly recommended that only qualified service technicians perform this service.
scabbaRd
SPARK ARRESTOR
The spark arrestor must be cleaned or replaced every 25
hours or yearly to ensure proper performance of the product.
Spark arrestors may be in different locations depending on
the model purchased. Please contact the nearest service
dealer for the location of the spark arrestor for your model.
STORING THE TRIMMER (1 MONTH OR LONGER)
See Figure 11.
Drain all fuel from tank into a container approved for
gasoline. Run engine until it stops.
Clean all foreign material from the hedge trimmer. Store
it in a well-ventilated place that is inaccessible to children. Keep away from corrosive agents such as garden
chemicals and de-icing salts.
Abide by all Federal and local regulations for the safe
storage and handling of gasoline.
Always place the scabbard on the cutting blades before
transporting or storing the unit.
Fig. 11
Page 13
Page 14
TROUBLESHOOTING
Problem Possible Cause Solution
Engine will not start. No spark.
No fuel.
Engine is flooded.
Starter rope pulls harder now than when
new.
Engine starts but will not accelerate. Engine requires approximately three min-
utes to warm up.
Check spark. Remove spark plug. Reattach
the spark plug cap and lay spark plug on
metal cylinder. Pull the starter rope and
watch for spark at spark plug tip. If there
is no spark, repeat test with a new spark
plug.
Push primer bulb until bulb is full of fuel.
If bulb does not fill, primary fuel delivery
system is blocked. Contact a servicing
dealer. If primer bulb fills, engine may be
flooded, proceed to next item.
Remove spark plug, turn trimmer so spark
plug hole is aimed at the ground. Rotate
the choke dial to “RUN” position and pull
starter cord 10 to 15 times. This will clear
excess fuel from engine. Clean and reinstall
spark plug. Pull starter three times with
choke dial at “RUN”. If engine does not
start, rotate choke dial to “FULL CHOKE”
position and repeat normal starting procedure. If engine still fails to start, repeat
procedure with a new spark plug.
Contact a servicing dealer.
Allow engine to completely warm up. If
engine does not accelerate after three
minutes, contact a servicing dealer.
Engine starts but will only run at high speed
at half choke.
Engine does not reach full speed and emits
excessive smoke.
Engine starts, runs, and accelerates but
will not idle.
Carburetor requires adjustment. Contact a servicing dealer.
Check lubricant fuel mixture.
Air filter is dirty.
Spark arrestor screen is dirty.
Idle speed screw on carburetor needs
adjustment.
Use fresh fuel and the correct 2-cycle
lubricant mix.
Clean air filter. Refer to Cleaning the Air
Filter Screen earlier in this manual.
Contact a servicing dealer.
Turn idle speed screw clockwise to increase idle speed. See figure 12.
IdlE spEEd
scREw
Fig. 12
Page 14
Page 15
WARRANTY
LIMITED WARRANTY STATEMENT
Homelite Consumer Products, Inc., (“Homelite”) warrants
to the original retail purchaser that this HOMELITE brand
outdoor product is free from defect in material and
workmanship and agrees to repair or replace, at Homelite’s,
discretion, any defective product free of charge within these
time periods from the date of purchase.
Two years for all models if used for personal, family, or
household use;
90 days for any unit used for other purposes, such as
rental or commercial.
This warranty extends to the original retail purchaser
only and commences on the date of the original retail
purchase.
Any part of the this product manufactured or supplied
by Homelite and found in the reasonable judgment of
Homelite to be defective in material or workmanship will
be repaired or replaced without charge for parts and labor
by a Homelite authorized service center.
The product, including any defective part, must be returned
to an authorized service dealer within the warranty period.
The expense of delivering the product to the dealer for
warranty work and the expense of returning it back to the
owner after repair or replacement will be paid by the owner.
Homelite’s responsibility in respect to claims is limited to
making the required repairs or replacements and no claim
of breach of warranty shall be cause for cancellation or
rescission of the contract of sale of any HOMELITE brand
product. Proof of purchase will be required by the dealer
to substantiate any warranty claim. All warranty work must
be performed by a Homelite authorized service center.
This warranty is limited to ninety (90) days from the date of
original retail purchase for any HOMELITE brand product
that is used for rental or commercial purposes, or any other
income-producing purpose.
This warranty does not cover any HOMELITE brand product
that has been subject to misuse, neglect, negligence, or
accident, or that has been operated in any way contrary
to the operating instructions as specified in this operator’s
manual. This warranty does not apply to any damage to
the product that is the result of improper maintenance or
to any product that has been altered or modified. The
warranty does not extend to repairs made necessary
by normal wear or by the use of parts or accessories
which are either incompatible with the HOMELITE
brand product or adversely affect its operation,
performance, or durability. In addition, this warranty does
not cover:
A. Tune-ups – Spark Plugs, Carburetor, Carburetor
Adjustments, Ignition, Filters
B. Wear items – Bump Knobs, Outer Spools, Cutting
Lines, Inner Reels, Starter Pulleys, Starter Ropes, Drive
Belts, Tines, Felt Washers, Hitch Pins, Mulching Blades,
Blower Fans, Blower and Vacuum Tubes, Vacuum Bags
and Straps, Guide Bars, Saw Chains
Homelite reserves the right to change or improve
the design of any HOMELITE brand product without
assuming any obligation to modify any product previously
manufactured.
ALL IMPLIED WARRANTIES ARE LIMITED IN DURATION
TO THE STATED WARRANTY PERIOD. ACCORDINGLY,
ANY SUCH IMPLIED WARRANTIES INCLUDING
MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR OTHERWISE, ARE DISCLAIMED IN
THEIR ENTIRETY AFTER THE EXPIRATION OF THE
APPROPRIATE TWO-YEAR, ONE-YEAR, OR NINETY-DAY
WARRANTY PERIOD. HOMELITE’S OBLIGATION UNDER
THIS WARRANTY IS STRICTLY AND EXCLUSIVELY
LIMITED TO THE REPAIR OR REPLACEMENT OF
DEFECTIVE PARTS AND HOMELITE DOES NOT ASSUME
OR AUTHORIZE ANYONE TO ASSUME FOR THEM ANY
OTHER OBLIGATION. SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY
TO YOU. HOMELITE ASSUMES NO RESPONSIBILITY
FOR INCIDENTAL, CONSEQUENTIAL, OR OTHER
DAMAGES INCLUDING, BUT NOT LIMITED TO, EXPENSE
OF RETURNING THE PRODUCT TO AN AUTHORIZED
HOMELITE SERVICE CENTER AND EXPENSE OF
DELIVERING IT BACK TO THE OWNER, MECHANIC’S
TRAVEL TIME, TELEPHONE OR TELEGRAM CHARGES,
RENTAL OF A LIKE PRODUCT DURING THE TIME
WARRANTY SERVICE IS BEING PERFORMED, TRAVEL,
LOSS OR DAMAGE TO PERSONAL PROPERTY, LOSS
OF REVENUE, LOSS OF USE OF THE PRODUCT,
LOSS OF TIME, OR INCONVENIENCE. SOME STATES
DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY
TO YOU.
This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
This warranty applies to all HOMELITE brand products
manufactured by or for Homelite and sold in the United
States and Canada.
To locate your nearest Homelite authorized service
center, dial 1-800-242-4672 or log on to our website at
www.homelite.com.
Page 15
Page 16
WARRANTY
THE FOLLOWING CALIFORNIA AIR RESOURCES BOARD (CARB) STATEMENT ONLY APPLIES TO MODEL NUMBERS
REqUIRED TO MEET THE CARB REqUIREMENTS.
HOMELITE CONSUMER PRODUCTS, INC., LIMITED WARRANTY STATEMENT FOR FEDERAL AND CALIFORNIA
EMISSION CONTROL SYSTEMS NON-ROAD AND SMALL OFF-ROAD ENGINES
YOUR WARRANTY RIGHTS AND OBLIGATIONS
The U.S. Environmental Protection Agency (EPA), the California Air Resources Board
(CARB), and Homelite Consumer Products, Inc., are pleased to explain the Emissions
Control System Warranty on your 2008 model year non-road or small off-road engine.
In California, new equipment that uses small off-road engines must be designed, built,
and equipped to meet the state’s stringent anti-smog standards. In other states, new
2000 and later model year non-road engines must be designed, built, and equipped
at the time of sale to meet the U.S. EPA regulations for small non-road engines. The
non-road engine must be free from defects in materials and workmanship which
cause it to fail to conform with U.S. EPA standards for the first two years of engine
use from the date of sale to the ultimate purchaser. Homelite Consumer Products,
Inc., must warrant the emission control system on your non-road or small off-road
engine for the period of time listed above provided there has been no abuse, neglect,
or improper maintenance of your non-road or small off-road engine.
Your emission control system may include parts such as the carburetor or fuel injection
system, the ignition system, catalytic converters, fuel tanks, valves, filters, clamps,
connectors, and other associated components. Also included may be hoses, belts
and connectors, and other emission-related assemblies.
Where a warrantable condition exists, Homelite Consumer Products, Inc., will repair
your non-road or small off-road engine at no cost to you, including diagnosis, parts,
and labor performed at an authorized service center for HOMELITE® brand outdoor
products.
MANUFACTURER’S WARRANTY COVERAGE:
This product’s emissions control system is warranted for two years. If any emissionrelated part on your engine is defective, the part will be repaired or replaced by
Homelite Consumer Products, Inc., free of charge.
OWNER’S WARRANTY RESPONSIBILITIES
(a) As the non-road or small off-road engine owner, you are responsible for the performance of the required maintenance listed in your operator’s manual. Homelite Consumer
Products, Inc., recommends that you retain all receipts covering maintenance on your
non-road or small off-road engine, but Homelite Consumer Products, Inc., cannot deny
warranty solely for the lack of receipts or for your failure to ensure the performance
of all scheduled maintenance. Any replacement part or service that is equivalent in
performance and durability may be used in non-warranty maintenance or repairs,
and shall not reduce the warranty obligations of Homelite Consumer Products, Inc.
(b) As the non-road or small off-road engine owner, you should be aware, however,
that Homelite Consumer Products, Inc., may deny you warranty coverage if your
non-road or small off-road engine or a part has failed due to abuse, neglect, improper
maintenance, or unapproved modifications.
(c) You are responsible for presenting your non-road or small off-road engine to an
authorized service dealer as soon as a problem exists. The warranty repairs should
be completed in a reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty rights and responsibilities, you
should contact a Homelite Consumer Products, Inc., Customer Representative at
1-800-242-4672.
DEFECT WARRANTY COVERAGE REqUIREMENTS:
(a) The warranty period begins on the date the engine or equipment is delivered to
an ultimate purchaser.
(b) General Emissions Warranty Coverage. Homelite Consumer Products, Inc., warrants to the ultimate purchaser and each subsequent purchaser that your non-road or
small off-road engine is designed, built, and equipped at the time of sale to conform
with all applicable regulations adopted by the California Air Resources Board or the
United States Environmental Protection Agency; and that it is free from defects in
materials and workmanship which cause the engine to fail to conform with applicable
regulations for a period of two years from the date the non-road or small off-road
engine is purchased by the initial purchaser.
(c) The warranty on emissions-related parts will be interpreted as follows: Any
warranted part that is not scheduled for replacement as required in the Emissions
Maintenance Schedule and Warranty Parts List set forth below is warranted for two
years. If any such part (including any part that is scheduled only for regular inspection) fails during the period of warranty coverage, it will be repaired or replaced at
any HOMELITE® Authorized Service Center at no charge. Any such part repaired
or replaced under warranty will be warranted for the remaining warranty period. A
statement to the effect of “repair or replace as necessary” would not reduce the
period of warranty coverage. Any warranted part that is scheduled for replacement
as required maintenance in the Emissions Maintenance Schedule and Warranty Parts
List is warranted for the period of time prior to the first scheduled replacement point
for that part. Any such part repaired or replaced under warranty is warranted for the
remainder of the period prior to the first scheduled replacement point, and will be
repaired or replaced at any HOMELITE® Authorized Service Center for no charge
until that replacement point is reached.
Homelite Consumer Products, Inc., shall remedy warranty defects at any authorized
HOMELITE® Authorized Service Center, including any distribution center that may be
franchised to service the subject engines. Any diagnostic work done at a HOMELITE®
Authorized Service Center shall be free of charge to the owner if such work determines
that a warranted part is defective. Any manufacturer-approved or equivalent replacement part may be used for any warranty maintenance or repairs on emission-related
parts, and must be provided free of charge to the owner if the part is still under
warranty. Homelite Consumer Products, Inc., is liable for damages to other engine
components caused by the failure of a warranted part still under warranty.
Add-on or modified parts that are not exempted by the California Air Resource Board
may not be used. The use of any non-exempted add-on or modified parts will be
grounds for disallowing a warranty claim. Homelite Consumer Products, Inc., will not
be liable to warrant failures of warranted parts caused by the use of a non-exempted
add-on or modified part.
The California Air Resources Board’s Emission Warranty Parts List specifically
defines the emission-related warranted parts. (EPA’s regulations do not include a
parts list, but the EPA considers emission-related warranted parts to include all the
parts listed below.) Homelite Consumer Products, Inc., will provide any documents
that describe its warranty procedures or policies within five days upon request by
the California Air Resources Board.
EMISSIONS PARTS LIST
Emissions parts vary from product to product. Your emissions control system warranty
applies to any of the following components that may be included on your product:
(1) Fuel Metering System
(i) Carburetor and internal parts (and/or pressure regulator or fuel injection
system).
(ii) Air/fuel ratio feedback and control system.
(iii) Cold start enrichment system.
(iv) Fuel Tank.
(2) Air Induction System
(i) Controlled hot air intake system.
(ii) Intake manifold.
(iii) Air filter.
(3) Ignition System
(i) Spark Plugs.
(ii) Magneto or electronic ignition system.
(iii) Spark advance/retard system.
(4) Exhaust Gas Recirculation (EGR) System
(i) EGR valve body and carburetor spacer, if applicable.
(ii) EGR rate feedback and control system.
(5) Air Injection System
(i) Air pump or pulse valve.
(ii) Valves affecting distribution of flow.
(iii) Distribution manifold.
(6) Catalyst or Thermal Reactor System
(i) Catalytic converter.
(ii) Thermal reactor.
(iii) Exhaust manifold.
(7) Particulate Controls
(i) Traps, filters, precipitators, and any other device used to capture particulate
emissions.
(8) Miscellaneous Items Used in Above Systems
(i) Electronic controls.
(ii) Vacuum, temperature, and time sensitive valves and switches.
(iii) Hoses, belts, connectors, and assemblies.
Homelite Consumer Products, Inc., will furnish with each new engine written instruc-
tions for its maintenance and use by the owner.
The Emissions Compliance Period referred to on the Emissions Compliance label
indicates the number of operating hours for which the engine has been shown to
meet Federal emission requirements. Category C=50 hours, B=125 hours, and
A=300 hours.
Page 16
Page 17
WARRANTY
CAL
L
1-800-242-4672
www
.homeli
te.com
THIS PRODUCT WAS MANUFACTURED WITH A CATALYST MUFFLER
Congratulations! You have made an investment toward protecting the environment. In order to maintain this product’s
original emission level, please refer to the maintenance section below.
EMISSIONS MAINTENANCE SCHEDULE AND WARRANTED PARTS LIST
Emissions Parts Inspect Before Clean Every Replace Clean Every Replace Every
Each Use 5 Hours Every 25 Hours 25 Hours 50 Hours
or Yearly or Yearly
CATALYTIC MUFFLER ASSEMBLY ................................................................................................................... X
AIR FILTER ASSY
includes:
Filter Screen ..................................................... X
SPARK SCREEN ..................................................................................................................X
FUEL TANK ASSY
includes:
Fuel Lines ........................ X
Fuel Cap .......................... X
IGNITION ASSY
includes:
Spark Plug ........................................................................................ X
ALL EMISSIONS-RELATED PARTS ARE WARRANTED FOR TWO YEARS OR FOR THE PERIOD OF TIME PRIOR TO
THE PARTS FIRST SCHEDULED REPLACEMENT WHICHEVER COMES FIRST.
MakE ThE MosT of youR puRchasE!
Go to www.homelite.com and register your new tool on-line.
Your product has been fully tested prior to shipment
to ensure your complete satisfaction.
For any questions about operating or maintaining
your product, call the Homelite Help Line!
To register your Homelite product or set up your eBox™ account by regular mail, please print the following information on a 3 in. x 5 in. card or standard postcard: your name, mailing address, phone numbers, email address,
Homelite product(s) purchased with item number from package, and serial number for each product. Mail the
card to: Homelite Consumer Products, Attn. Homelite Registration, 1428 Pearman Dairy Road, Anderson, SC
29625.To receive information on our company and products, please include the following statement on your
registration card: “Send me information on your products and company using the contact information I am providing with this product registration.”
Page 17
Page 18
OPERATOR’S MANUAL
26cc Hedge Trimmer
UT40502 /UT40903
(ALL VERSIONS)
WARNING:
The engine exhaust from this product contains chemicals known to the State of California to
cause cancer, birth defects or other reproductive harm.
CALIFORNIA PROPOSITION 65
• PARTS AND SERVICE
Prior to requesting service or purchasing replacement parts, please obtain your model
and serial number from the product data plate.
• MODEL NUMBER
• SERIAL NUMBER
• HOW TO OBTAIN REPLACEMENT PARTS:
Replacement parts can be purchased online at www.homelite.com or by calling
1-800-242-4672. Replacement parts can also be obtained at one of our Authorized
Service Centers.
• HOW TO LOCATE AN AUTHORIZED SERVICE CENTER:
Authorized Service Centers can be located online at www.homelite.com or by calling
1-800-242-4672.
• HOW TO OBTAIN CUSTOMER OR TECHNICAL SUPPORT:
To obtain Customer or Technical Support please contact us at 1-800-242-4672.
987000-041
3-25-08 (REV:04)
UT40502/UT40903
HOMELITE CONSUMER PRODUCTS, INC.
1428 Pearman Dairy Road
Anderson, SC 29625
Phone 1-800-242-4672
www.homelite.com
Loading...