OPERATOR’S MANUAL
Expand-it
™
Tiller Attachment
UT15550B
Your Expand-it™ Tiller Attachment has been engineered and manufactured to a high standard for dependability, ease of
operation, and operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before
using this product.
Thank you for buying an Expand-it™ product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
TABLE OF CONTENTS
Introduction ................................................................................................................................................................... 2
General Safety Rules .................................................................................................................................................... 3
Specific Safety Rules .................................................................................................................................................... 4
Symbols ........................................................................................................................................................................ 5
Features ....................................................................................................................................................................... 6
Assembly ...................................................................................................................................................................7-8
Operation ................................................................................................................................................................. 8-10
Maintenance ............................................................................................................................................................... 11
Exploded View and Parts List ................................................................................................................................12-13
Warranty ...................................................................................................................................................................... 15
Parts, Ordering, and Service ..........................................................................................................................Back Page
INTRODUCTION
This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability
have been given top priority in the design of this product making it easy to maintain and operate.
2
GENERAL SAFETY RULES
WARNING:
Read and understand all instructions. Failure to fol-
low all instructions listed below, may result in electric
shock, fire, and/or serious personal injury.
SAVE THESE INSTRUCTIONS
Read these instructions and the instructions for the power
head thoroughly before using tiller.
Know the tool. Read and understand the operator’s
manual and observe the warnings and instruction labels
affixed to the tool.
Do not allow children or untrained individuals to use this
unit.
Wear safety glasses or goggles that are marked to comply
with ANSI Z87.1 standards and hearing and head protection when operating this unit.
Wear heavy long pants, boots, and gloves. Do not wear
loose fitting clothing, short pants, jewelry of any kind, or
go barefoot.
Secure long hair so it is above shoulder level to prevent
entanglement in any moving parts.
Keep all bystanders, children, and pets at least 50 ft.
away.
Stay alert, watch what you are doing, and use common
sense when operating a power tool. Do not use tool while
tired or under the influence of drugs, alcohol, or medication. A moment of inattention while operating power tools
may result in serious personal injury.
Do not operate in poor lighting.
Do not overreach. Keep proper footing and balance at all
times. Proper footing and balance enables better control
of the tool in unexpected situations.
Keep all parts of your body away from any moving part.
When using the attachment on a power head with a
gasoline engine, do not touch areas around the muffler
or cylinder of the power head. These parts get hot from
operation. Failure to heed this warning could result in
possible serious personal injury.
Always stop the engine and remove the spark plug wire or
disconnect from power supply before making any adjustments or repairs except for carburetor adjustments.
Inspect unit before each use for loose fasteners and
damaged or missing parts. Correct before using the tiller
attachment. Failure to do so can cause serious injury.
Use only original manufacturer’s replacement parts.
Failure to do so may cause poor performance, possible
injury, and will void your warranty.
Do not, under any circumstance, use any attachment or
accessory on this product, which was not provided with
the product, or identified as appropriate for use with this
product in the operator’s manual.
Avoid dangerous environments. Do not use the attach-
ment in damp or wet locations.
Do not use in rain.
Use the right attachment. Do not use attachment for any
job except that for which it is intended.
SAFETY RULES WHEN ATTACHMENT IS
ATTACHED TO AN ELECTRIC POWER HEAD
When this attachment is being used with the recom-
mended electric power unit, refer to Electrical Safety
Rules in the electric power unit’s Operator’s Manual, in
addition to items contained in this manual.
Make sure the cord is located so that it will not be stepped
on, tripped over, or otherwise subjected to damage or
stress. Keep cord clear of the working area.
� Do not abuse the power cord. Never carry the product
by the cord. Never yank the plug out of the receptacle.
Keep the cord away from heat, oil, and sharp edges.
� Inspect extension cords for deterioration, cuts, or cracks
in the insulation. Repair or replace the cords if any defects
appear.
Keep the extension cord clear of the working area. Posi-
tion the cord so that it will not come in contact with the
tiller attachment when in use. Failure to do so can result
in serious personal injury.
�� Check extension cords before each use. If damaged
replace them immediately. Touching the damaged area
could cause serious injury due to electrical shock.
3
SPECIFIC SAFETY RULES
Rotating tines can cause severe injury, keep all body parts
away from rotating tines.
Use extreme caution when reversing or pulling the
machine towards you.
Always be sure of your footing; keep a firm hold on the
handles and walk; never run.
If the tiller should start to vibrate abnormally or become
noisy, stop the motor and check immediately for the
cause. Abnormal noise is generally a warning of trouble.
Keep all fasteners tight to be sure the tiller is in safe work-
ing condition.
Check that the hitch pins are fully inserted on the tine
shaft before each use.
Do not operate power equipment after it has been
dropped or damaged. Return it to your nearest authorized
servicing dealer for inspection and repair.
Stop the engine whenever you leave the tiller, or when
making any repairs or inspections.
Make sure all proper guards and other safety devices
are properly and securely attached before using this
product.
Be extremely careful when tilling in hard ground. The tines
could catch in the ground and propel the tiller forward.
Do not overload the capacity of the machine by attempt-
ing to till too deep at too fast a speed.
Inspect the area where the equipment is to be used and
remove all foreign objects.
Keep hands, feet, and other body parts away from rotat-
ing parts.
Always stop the engine and remove the spark plug wire
or disconnect from power supply before installing attachments or making any adjustments.
Before storing the unit, allow the engine to cool.
When not in use, store the tiller in a dry place which is
inaccessible to children.
Save these instructions. Refer to them frequently and use
them to instruct others who may use this tool. If you loan
someone this tool, loan them these instructions also to
prevent misuse of the product and possible injury.
4
SYMBOLS
Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOL NAME EXPLANATION
Safety Alert Symbol Precautions that involve your safety.
Read The Operator’s Manual
Eye and Hearing Protection Wear eye and hearing protection when operating this equipment.
Keep Bystanders Away Keep all bystanders at least 50 ft. away.
Rotating Tines
The following signal words and meanings are intended to explain the levels of risk associated with this product.
To reduce the risk of injury, user must read and understand operator’s
manual before using this product.
Danger — Keep hands and feet away from rotating tines. Rotating
tines will cause injury.
SYMBOL SIGNAL MEANING
DANGER:
WARNING:
CAUTION:
Indicates an imminently hazardous situation, which, if not avoided, will result
in death or serious injury.
Indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
Indicates a potentially hazardous situation, which, if not avoided, may result in
minor or moderate injury.
CAUTION:
(Without Safety Alert Symbol) Indicates a situation that may result in property
damage.
SERVICE
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to your nearest
AUTHORIZED SERVICE CENTER for repair. When servicing, use only identical replacement parts.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles or
safety glasses with side shields and, when needed, a full face shield. We recommend Wide Vision
Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye
protection which is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
WARNING:
To avoid serious personal injury, do not attempt to use
this product until you read thoroughly and understand
completely the operator’s manual. If you do not under
stand the warnings and instructions in the operator’s
manual, do not use this product. Call Expand-it customer
service for assistance.
-
5
FEATURES
PRODUCT SPECIFICATIONS
Weight ........................................................................................................................................................................13.5 lbs.
END CAP
“J” HANDLE
TILLER ATTACHMENT SHAFT
SHIELD
TINES
GEAR BOX
HANGER CAP
Fig. 1
KNOW YOUR TILLER ATTACHMENT
See Figure 1.
The safe use of this product requires an understanding of the information on the tool and in this operator’s manual as well
as a knowledge of the project you are attempting. Before use of this product, familiarize yourself with all operating features
and safety rules.
6
ASSEMBLY
UNPACKING
This product has been shipped completely assembled.
Carefully remove the items from the box. Make sure that
all items listed in the packing list are included.
Inspect the product carefully to make sure no breakage
or damage occurred during shipping.
Do not discard the packing material until you have care-
fully inspected and satisfactorily operated the tool.
If any parts are damaged or missing, please call
1-800-242-4672 for assistance.
PACKING LIST
Expand-it™ Tiller Attachment
J-Handle with Mounting Hardware
Hanger Cap
Operator’s Manual
WARNING:
If any parts are damaged or missing, do not operate
this tool until the parts are replaced. Failure to heed this
warning could result in serious personal injury.
WARNING:
Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any such
alteration or modification is misuse and could result in a
hazardous condition leading to possible serious personal
injury.
CONNECTING POWER HEAD TO EXTENSION
SHAFT AND TILLER ATTACHMENT
See Figure 2.
The tiller attachment connects to the power head or, for extra
reach, to an extension shaft by means of a coupler device.
WARNING:
Never attach or adjust any attachment while power head
is running. Failure to stop the engine and disconnect the
spark plug wire or disconnect from power supply may
cause serious personal injury.
POWER HEAD
SHAFT
GUIDE
RECESS
BUTTON
TILLER SHAFT
To install the attachment:
Loosen the knob on the coupler of the power head shaft
and remove the end cap from the attachment.
� Push in the button located on the shaft of the tiller attach-
ment.
� Align the button with the guide recess on the power head
coupler and slide the two shafts together. Rotate attachment shaft until button locks into the positioning hole.
NOTE: If the button does not release completely in the
positioning hole, the shaft is not locked into place. Slightly
rotate from side to side until the button is locked into
place.
� Tighten the knob securely.
COUPLER
POSITIONING
HOLE
KNOB
Fig. 2
WARNING:
Be certain the knob is fully tightened before operating
equipment; check it periodically for tightness during use
to avoid serious injury.
To remove:
� Loosen the knob.
� Push in the button and twist the shafts to remove and
separate ends.
7
ASSEMBLY
ATTACHING THE J-HANDLE
See Figure 3.
The J-handle included with the Expand-it™ Tiller Attachment
provides a barrier to assist the operator in maintaining a safe
distance from the rotating tines. If the power head to which
the tiller attachment will be mounted does not have such a
handle, install the provided handle.
Hold the top and bottom clamp snugly in position on
the shaft housing so that handle will be located to the
operator’s left.
Insert the end of the handle between the clamps.
Align the bolt holes and push the long bolt (1/4-20 x 1-1/2
in.) through the handle side.
Place short bolt (1/4-20 x 1 in.) through opposite side of
clamp. Install flat washers, lock washers, and hex nuts
to hold the assembly in place.
After assembly is complete, adjust the position of the
handle for best balance and comfort.
Tighten the long bolt first and then the short bolt.
FRONT
HANDLE
CLAMP
BOLT
(1/4-20 x 1 in.)
CLAMP
BOLT
(1/4-20 x 1-1/2 in.)
FLAT WASHER
OPERATION
WARNING:
Do not allow familiarity with tools to make you careless.
Remember that a careless fraction of a second is
sufficient to inflict serious injury.
WARNING:
Always wear safety goggles or safety glasses with side
shields when operating power tools. Failure to do so
could result in objects being thrown into your eyes
resulting in possible serious injury.
WARNING:
Do not use any attachments or accessories not
recommended by the manufacturer of this tool. The use
of attachments or accessories not recommended can
result in serious personal injury.
LOCK WASHER
HEX NUT
Fig. 3
APPLICATIONS
You may use this tool for the purposes listed below:
Breaking up garden soil to prepare seed beds for
planting
Shallow cultivating to remove weeds
OPERATING THE TILLER
See Figure 4.
Hold the tiller attachment with your right hand on the rear
handle and your left hand on the front handle. Keep a firm
grip with both hands while in operation.
In nearly all types of soil, it is not necessary or recommended
to operate the tiller attachment at full throttle. Doing so
consistently will shorten the life of the engine and drivetrain.
Partial throttle will usually be sufficient.
8
OPERATION
WARNING:
Keep hands and feet away from the rotating tines. Rotating tines will cause serious personal injury.
NOTE: The tines of the tiller may rotate when the engine is
started.
Move the tiller to the work area before starting the
engine.
With the tiller on flat level ground, start the engine of the
power head. Refer to the operator’s manual of your power
head.
Hold the handles firmly, depress the throttle trigger to
increase the engine speed to a moderate speed, then
lower the tiller so the tines can make contact with the
ground.
Pull the tiller carefully toward you while it is digging into
the soil’s surface.
NOTE: Pulling the tiller carefully toward you while it is
digging into the soil will reduce your effort and make the
tilling easier.
WARNING:
To avoid personal injury, never carry the tiller while the
engine is running. Move the tiller to the work area before
starting the engine.
WARNING:
After extended periods of use, the tiller gearbox may
become hot. To avoid burns, do not touch the gearbox
until it has had time to cool down.
TINE POSITION
See Figure 5.
Tine blades are marked with the corresponding letters (A,
B, C, and D).
NOTE: All four tines on this unit are different and must be
installed correctly or the tiller will not function properly. When
the tines are properly mounted, the angled portion of the tine
blade should enter the soil first, not the straight portions.
FELT
WASHER
TINE D
FLAT EDGE
Fig. 4
CAUTION:
Wear heavy gloves when installing, removing, or adjusting the tiller tines. With wear, the tiller tines may become
sharper.
WARNING:
Stop the engine and disconnect the spark plug wire or
disconnect from power supply before adjusting the tiller
tines.
GEAR
BOX
FELT
WASHER
TINE A
HITCH
PIN
ANGLED EDGE
TINE SHAFT
9
HITCH
PINTINE C TINE B
Fig. 5
OPERATION
REGULAR TINE PATTERN
See Figure 6.
For most applications, the regular tine pattern will work best.
This is the pattern set by the factory.
NOTE: Pay attention to the hub position in relationship to
the tines.
NARROW TINE PATTERN
See Figure 7.
When tilling in confined areas or rows, a narrow tine pattern
may be required. For a narrow tine pattern:
Remove hitch pin from each side of the tiller.
Remove the left and right outer tines (A and D).
Remove felt washers.
Replace hitch pin in alternate holes on each side of
shaft.
NOTE: Do not force the tines on or off the shaft. If you
experience difficulties when removing the tines, apply some
penetrating oil on the shaft. When reinstalling the tines, make
sure to clean and oil the shaft and the tine hubs.
STONY OR ROCKY SOIL TINE PATTERN
See Figure 8.
If you are tilling in stony or rocky soil and experience continual rock jams, there is an additional tine pattern that will
help correct the problem. In the stony soil tine pattern, the
center gap is wider than in the regular tine pattern. This will
require additional passes to till the area. For a stony soil
tine pattern:
Remove hitch pin from each side of the tiller.
Remove tines and felt washers from the shaft.
Reinstall tines B and C on opposite sides of the shaft.
When facing the tiller attachment, tine B will now be on
the left and tine C will be on the right.
Reinstall felt washers.
Reinstall tines A and D. Tines D and B will now be on one
side, with tines A and C on the other.
Replace hitch pins.
REGULAR TINE PATTERN
HITCH PIN
FELT WASHER
D
NARROW TINE PATTERN
STONY OR ROCKY SOIL TINE PATTERN
C
FRONT VIEW
C
FRONT VIEW
B
TINE HUB
A
Fig. 6
HITCH PIN
B
Fig. 7
HITCH PIN
10
D
B C
FRONT VIEW
A
Fig. 8
MAINTENANCE
WARNING:
When servicing, use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.
WARNING:
Always wear safety goggles or safety glasses with side
shields during tool operation. If operation is dusty, also
wear a dust mask.
HANGER
CAP
HOLE
WARNING:
Before inspecting, cleaning, or servicing the machine,
shut off engine, wait for all moving parts to stop, and
disconnect spark plug wire and move it away from spark
plug or disconnect from power supply. Failure to follow
these instructions can result in serious personal injury or
property damage.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
Do not at any time let brake fluids, gasoline, petroleumbased products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or de
stroy plastic which may result in serious personal injury.
You can often make adjustments and repairs described here.
For other repairs, have the tool serviced by an authorized
service dealer.
-
SECONDARY
HOLE
BUTTON
Fig. 9
ATTACHING THE STORAGE HANGER
See Figure 9.
There are two ways to hang the attachment for storage.
To use the hanger cap, push in the button and place the
hanger cap over end of the lower end attachment shaft.
Slightly rotate the cap from side to side until the button
locks into place.
The secondary hole in the attachment shaft can be used
for hanging purposes as well.
STORING THE TILLER ATTACHMENT
Store the tiller attachment in a well-ventilated place that is
inaccessible to children. Keep away from corrosive agents
such as garden chemicals and de-icing salts.
TINE MAINTENANCE
Occasionally apply a few drops of oil to the shaft to keep
the tines free on the shaft.
If tines are being replaced due to wear, all four tines
should be replaced as a set.
11
EXPLODED VIEW AND PARTS LIST
5
16
13
19
20
14
21
15
19
20
13
17
1
4
3
2
6
22
7
8
9
12
18
10
11
7
12
12
EXPLODED VIEW AND PARTS LIST
Key Part
No. No. Description Qty.
1 220029002 Gear Case and Drive Shaft Assembly (Includes Key Nos. 2 and 17) ...................
2 940657006 Warning Label ......................................................................................................1
3 308635001 Tine Shield Assembly (Includes Key Nos. 4 and 6) ..............................................1
4 940627034 Expand-it Label ....................................................................................................1
5 660955001 * Screw (1/4-20 x 5/8 in.) ........................................................................................ 4
6 940654015 Warning Label ......................................................................................................1
7 638001004 * Hitch Pin (3/4 in.) .................................................................................................. 2
8 308693004 Tine Assembly D ..................................................................................................1
9 308693003 Tine Assembly C ..................................................................................................1
10 308693002 Tine Assembly B .................................................................................................. 1
11 308693001 Tine Assembly A ..................................................................................................1
12 900755001 Felt Washer .......................................................................................................... 2
13 638014001 Handle Bar Clamp ................................................................................................2
14 660643002 * Bolt (1/4-20 x 1 in.) ...............................................................................................1
15 660643001 * Bolt (1/4-20 x 1-1/2 in.) ........................................................................................1
16 308046001 J-Handle and Grip ................................................................................................1
17 940654014 Warning Label, UL ...............................................................................................1
1
18 678132001 * Lock Nut (1/4-20) ................................................................................................. 4
19 678013001 * Washer .................................................................................................................2
20 678012001 * Lock Washer ........................................................................................................ 2
21 678016001 * Hex Nut (1/4-20) ...................................................................................................2
22 518019001 Hanger Cap ..........................................................................................................1
983000934 Operator’s Manual (960994002) ...........................................................................1
983000934R Repair Sheet ........................................................................................................1
* STANDARD HARDWARE ITEM — MAY BE PURCHASED LOCALLY
13
NOTES
14
WARRANTY
LIMITED WARRANTY STATEMENT
Techtronic Industries North America, Inc., warrants to the
original retail purchaser that this EXPAND-IT brand product
is free from defect in material and workmanship and agrees
to repair or replace, at Techtronic Industries North America,
Inc.’s discretion, any defective product free of charge within
these time periods from the date of purchase.
� One year for the following units: all Yard Broom, Trimlite,
and Bandit models;
� Two years if the product is used for personal, family or
household use;
� 90 days if used for any other purpose, such as commercial
or rental.
This warranty extends to the original retail purchaser only and
commences on the date of the original retail purchase.
Any part of the product found in the reasonable judgment
of Techtronic Industries North America, Inc., to be defective
in material or workmanship will be repaired or replaced
without charge for parts and labor by an Expand-it authorized
service center.
The product, including any defective part, must be returned
to an Expand-it authorized service center within the warranty
period. The expense of delivering the product to the service
center for warranty work and the expense of returning it
back to the owner after repair or replacement will be paid
by the owner. Techtronic Industries North America, Inc.’s
responsibility in respect to claims is limited to making the
required repairs or replacements and no claim of breach of
warranty shall be cause for cancellation or rescission of the
contract of sale of any EXPAND-IT brand product. Proof of
purchase will be required by the dealer to substantiate any
warranty claim. All warranty work must be performed by an
Expand-it authorized service center.
This warranty is limited to ninety (90) days from the date of
original retail purchase for any EXPAND-IT brand product
that is used for rental or commercial purposes, or any other
income-producing purpose.
This warranty does not cover any product that has been
subject to misuse, neglect, negligence, or accident, or that
has been operated in any way contrary to the operating
instructions as specified in this operator’s manual. This
warranty does not apply to any damage to the product that
is the result of improper maintenance or to any product that
has been altered or modified. The warranty does not extend
to repairs made necessary by normal wear or by the use of
parts or accessories which are either incompatible with the
EXPAND-IT brand product or adversely affect its operation,
performance, or durability.
In addition, this warranty does not cover:
A. Tune-ups – Spark Plugs, Carburetor, Carburetor
Adjustments, Ignition, Filters
B. Wear items – Bump Knobs, Outer Spools, Cutting Lines,
Inner Reels, Starter Pulleys, Starter Ropes, Drive Belts,
Tines, Felt Washers, Hitch Pins, Mulching Blades, Blower
Fans, Blower and Vacuum Tubes, Vacuum Bags and
Straps, Guide Bars, Saw Chains
Techtronic Industries North America, Inc., reserves the right
to change or improve the design of any EXPAND-IT brand
product without assuming any obligation to modify any
product previously manufactured.
ALL IMPLIED WARRANTIES ARE LIMITED IN DURATION
TO THE STATED WARRANTY PERIOD. ACCORDINGLY,
ANY SUCH IMPLIED WARRANTIES INCLUDING
MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR OTHERWISE, ARE DISCLAIMED IN THEIR
ENTIRETY AFTER THE EXPIRATION OF THE APPROPRIATE
TWO-YEAR, ONE-YEAR, OR NINETY-DAY WARRANTY
PERIOD. TECHTRONIC INDUSTRIES NORTH AMERICA,
INC.’S OBLIGATION UNDER THIS WARRANTY IS
STRICTLY AND EXCLUSIVELY LIMITED TO THE REPAIR OR
REPLACEMENT OF DEFECTIVE PARTS AND TECHTRONIC
INDUSTRIES NORTH AMERICA, INC., DOES NOT ASSUME
OR AUTHORIZE ANYONE TO ASSUME FOR THEM ANY
OTHER OBLIGATION. SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY
TO YOU. TECHTRONIC INDUSTRIES NORTH AMERICA,
INC., ASSUMES NO RESPONSIBILITY FOR INCIDENTAL,
CONSEQUENTIAL, OR OTHER DAMAGES INCLUDING, BUT
NOT LIMITED TO, EXPENSE OF RETURNING THE PRODUCT
TO AN EXPAND-IT AUTHORIZED SERVICE CENTER AND
EXPENSE OF DELIVERING IT BACK TO THE OWNER,
MECHANIC’S TRAVEL TIME, TELEPHONE OR TELEGRAM
CHARGES, RENTAL OF A LIKE PRODUCT DURING THE TIME
WARRANTY SERVICE IS BEING PERFORMED, TRAVEL,
LOSS OR DAMAGE TO PERSONAL PROPERTY, LOSS OF
REVENUE, LOSS OF USE OF THE PRODUCT, LOSS OF
TIME, OR INCONVENIENCE. SOME STATES DO NOT ALLOW
THE EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION
OR EXCLUSION MAY NOT APPLY TO YOU.
This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
This warranty applies to all EXPAND-IT brand products
manufactured by or for Techtronic Industries North America,
Inc., and sold in the United States and Canada.
To locate your nearest Expand-it authorized service center,
dial 1-800-242-4672.
15
OPERATOR’S MANUAL
Expand-it
™
Tiller Attachment
UT15550B
SERVICE
For parts or service, contact your nearest Expand-it™ authorized service center. Be sure to provide all
relevant information when you call or visit. For the location of the authorized service center nearest
you, please call 1-800-242-4672 or visit us online at www.homelite.com.
REPAIR PARTS
The model number of this tool is found on a plate or label attached to the housing. Please record
the serial number in the space provided below.
MODEL NUMBER
SERIAL NUMBER
UT15550B
TECHTRONIC INDUSTRIES NORTH AMERICA, INC.
1428 Pearman Dairy Road
Anderson, SC 29625
Phone 1-800-242-4672
983000-934
2-27-06 (REV:00)
16
Loading...