Homelite UT08947 User Manual

OPERATOR’S MANUAL

VAC ATTACK II

UT08544/UT08546/UT08947

Your blower has been engineered and manufactured to our high standard for dependability, ease of operation, and operator
safety. When properly cared for, it will give you years of rugged, trouble-free performance.

WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using

this product.

Thank you for your purchase.

SAVE THIS MANUAL FOR FUTURE REFERENCE

TABLE OF CONTENTS

 Introduction ..................................................................................................................................................................... 2

� General Safety Rules ....................................................................................................................................................... 3

� Specific Safety Rules ....................................................................................................................................................... 4

� Symbols ........................................................................................................................................................................5-6

�� Features ........................................................................................................................................................................7-8

�� Assembly ....................................................................................................................................................................9-11

� Operation ..................................................................................................................................................................12-15

� Maintenance ............................................................................................................................................................. 16-17

 Accessories ................................................................................................................................................................... 17

� Troubleshooting ............................................................................................................................................................. 18

 Warranty ...................................................................................................................................................................19-21

 Parts Ordering / Service ................................................................................................................................................ 22

INTRODUCTION

This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability
have been given top priority in the design of this product making it easy to maintain and operate.

Page 2

GENERAL SAFETY RULES

WARNING:

READ AND UNDERSTAND ALL INSTRUCTIONS.

Failure to follow all instructions listed below, may result
in electric shock, fire and/or serious personal injury.

SAVE THESE INSTRUCTIONS

 Do not allow children or untrained individuals to use this

unit.

 Never start or run the engine inside a closed area; breath-

ing exhaust fumes can kill.

 Wear eye protection which is marked to comply with ANSI

Z87.1 as well as hearing protection when operating this
equipment.

 Keep all bystanders, children, and pets at least 50 ft.

away.

 Wear heavy long pants, boots, and gloves. Do not wear

loose fitting clothing, short pants, jewelry of any kind, or
go barefoot.

 To reduce the risk of injury associated with objects being

drawn into rotating parts, do not wear loose clothing,
scarves, neck chains, and the like.

 Secure long hair so it is above shoulder level to prevent

entanglement in any rotating parts.

 Do not operate this unit when you are tired, ill, or under

the influence of alcohol, drugs, or medication.

 Do not operate in poor lighting.
 Keep all parts of your body away from any moving parts

and all hot surfaces of the unit.

 Wear a face filter mask in dusty conditions to reduce the

risk of injury associated with the inhalation of dust.

 Check the work area before each use. Remove all objects

such as rocks, broken glass, nails, wire, or string which
can be thrown or become entangled in the machine.

 Keep firm footing and balance. Do not overreach. Over-

reaching can result in loss of balance or exposure to hot
surfaces.

 Never operate the unit without a spark arrestor screen;

this screen is located inside the muffler.

� Product users on United States Forest Service land, and

in some states, must comply with fire prevention regula­tions.

 This product is equipped with a spark arrestor; however,

other user requirements may apply. Check with the fed-

eral, state, or local authorities in your area.
� Before storing, allow the engine to cool.
� Empty fuel tank and restrain the unit from moving before

transporting in a vehicle.
� To reduce the risk of fire and burn injury, handle fuel with

care. It is highly flammable.
� Do not smoke while handling fuel.
� Mix and store fuel in a container approved for gasoline.
� Mix fuel outdoors where there are no sparks or flames.
� Select bare ground, stop engine, and allow to cool before

refueling.
� Loosen fuel cap slowly to release pressure and to keep

fuel from escaping around the cap.
� Tighten the fuel cap securely after refueling.
� Wipe spilled fuel from the unit. Move 30 ft. away from

refueling site before starting engine.
 Never attempt to burn off spilled fuel under any circum-

stances.
� Use only identical manufacturer’s replacement parts and

accessories. Use of any other parts may create a hazard

or cause product damage.
� Maintain the unit per maintenance instructions in this

Operator’s Manual.
� Inspect the unit before each use for loose fasteners, fuel

leaks, etc. Replace damaged parts.

Page 3

SPECIFIC SAFETY RULES

 Do not operate vacuum without vacuum bag installed;

flying debris could cause serious injury. Always close
vacuum bag completely before operating.

� Always hold the blower in your right hand, refer to the

Operation section, later in this manual for additional
information.

� To reduce the risk of hearing loss associated with sound

level(s), hearing protection is required.

� Rotating impeller blades can cause severe injury. Stop

the engine before opening the vacuum door or installing /
changing tubes. Do not put hands or any other object into
the vacuum tubes while they are installed on the unit.

� To reduce the risk of injury associated with contacting

rotating parts, stop the engine before installing or remov­ing attachments. Do not operate without guard(s) in place.
Always disconnect the spark plug before performing
maintenance or accessing any movable parts.

� Do not point the blower nozzle in the direction of people

or pets.
� Never run the unit without the proper equipment

attached.
 When used as a blower, always install the blower tubes.

When used as a vacuum, always install the vacuum

tubes and vacuum bag. Make sure the vacuum bag is

completely zipped when the unit is running to avoid flying

debris.
 Avoid situations that could catch the vacuum bag on

fire. Do not operate near an open flame. Do not vacuum

warm ash from fireplaces, barbeque pits, brush piles, etc.

Do not vacuum discarded cigars or cigarettes unless the

cinders are completely cool.

Page 4

SYMBOLS

Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpre­tation of these symbols will allow you to operate the tool better and safer.

SYMBOL NAME DESIGNATION/EXPLANATION

Safety Alert

Read The Operator’s Manual

Eye and Hearing Protection

Long Hair

Blower Tubes

Vacuum Door

Loose Clothing

Gasoline and Oil

Precautions that involve your safety.

To reduce the risk of injury, user must read and understand
operator’s manual before using this product.

Wear eye and hearing protection when operating this equipment.

Failure to keep long hair away from the air inlet could result in
personal injury.

Do not operate without tubes in place.

Do not run unit while vacuum door is unsecured.

Failure to keep loose clothing from being drawn into air intake
could result in personal injury.

Use unleaded gasoline intended for motor vehicle use with an
octane rating of 87 [(R + M)/2] or higher. This product is powered
by a 2-cycle engine and requires pre-mixing gasoline and 2-cycle
oil.

Page 5

SYMBOLS

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL SIGNAL MEANING

DANGER: Indicates an imminently hazardous situation, which, if not avoided, will

result in death or serious injury.

WARNING: Indicates a potentially hazardous situation, which, if not avoided, could

result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may

result in minor or moderate injury.

CAUTION: (Without Safety Alert Symbol) Indicates a situation that may result in

property damage.

SERVICE

Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to your nearest
AUTHORIZED SERVICE CENTER for repair. When servicing,
use only identical replacement parts.

WARNING:

To avoid serious personal injury, do not attempt to use this
product until you read thoroughly and understand com­pletely the operator’s manual. If you do not understand
the warnings and instructions in the operator’s manual,
do not use this product. Call Homelite customer service
for assistance.

WARNING:

The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles or
safety glasses with side shields and, when needed, a full face shield. We recommend Wide Vision
Safety Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye
protection which is marked to comply with ANSI Z87.1.

SAVE THESE INSTRUCTIONS

Page 6

FEATURES

PRODUCT SPECIFICATIONS

Weight .........................................................................................................................................................................9.8 lbs.

Engine displacement .......................................................................................................................................................30cc

Air Velocity:

MPH ...............................................................................................................................................................................200

CFM ...............................................................................................................................................................................420

HIGH VELOCITY NOZZLE

WET LEAF

SCRAPER

WIDE SWEEPER

NOZZLE

BLOWER TUBE

UPPER HANDLE

TUBE CLAMP

LOWER HANDLE

CRUISE CONTROL
(THROTTLE LOCK)

DOOR KNOB

THROTTLE TRIGGER

INLET COVER

DOOR

Fig. 1

Page 7

FEATURES

VACUUM BAG

SHOULDER STRAP

TUBE CLAMP

UPPER VACUUM

TUBE

LOWER VACUUM

TUBE

VACUUM BAG

ADAPTOR

ENGINE

SWITCH

VACUUM BAG

STARTER GRIP

PRIMER

BULB

CHOKE LEVER

KNOW YOUR BLOWER

See Figures 1 - 2.

The safe use of this product requires an understanding of
the information on the tool and in this operator’s manual as
well as a knowledge of the project you are attempting. Before
use of this product, familiarize yourself with all operating
features and safety rules.

BLOWER TUBES

The blower tubes can be assembled and installed on the
blower using no tools.

CRUISE CONTROL / THROTTLE LOCK

The cruise control (throttle lock) feature allows you to oper­ate the blower without continuously holding the throttle
trigger.

HIGH VELOCITY NOZZLE

The high velocity nozzle allows you to scrape wet leaves or
debris while operating the blower.

MOTOR

The blower has a powerful 30cc engine with sufficient power
to handle tough blowing and vacuuming jobs.

LOWER HANDLE

Fig. 2

MULCHER

The blower is equipped with a mulcher feature that efficiently
reduces leaves at a 12:1 ratio.

THROTTLE TRIGGER

The blower can be operated at any speed between idle and
full throttle.

VACUUM

The blower will convert to a powerful vacuum/mulcher using
no tools.

VACUUM BAG

The vacuum bag attaches to the blower easily using the
vacuum bag adaptor.

VACUUM TUBES

The vacuum tubes can be installed on the blower without
using any tools.

WIDE SWEEPER NOZZLE

The wide sweeper nozzle allows for more area to be covered
during blower operation.

Page 8

ASSEMBLY

UNPACKING

This product requires assembly.
 Carefully remove the tool and any accessories from the

box. Make sure that all items listed in the packing list are
included.

 Inspect the tool carefully to make sure no breakage or

damage occurred during shipping.

 Do not discard the packing material until you have care-

fully inspected and satisfactorily operated the tool.

 If any parts are damaged or missing, please call

1-800-242-4672 for assistance.

PACKING LIST

Blower
Blower Tube
Wide Sweeper Nozzle
High Velocity Nozzle
Upper and Lower Vacuum Tubes
Vacuum Bag
Bag Adaptor
Tube Clamp
2-Cycle Engine Oil
Operator’s Manual

WARNING:

If any parts are damaged or missing, do not operate
this tool until the parts are replaced. Failure to heed this
warning could result in serious personal injury.

WARNING:

Do not attempt to modify this tool or create accesso­ries not recommended for use with this tool. Any such
alteration or modification is misuse and could result in a
hazardous condition leading to possible serious personal
injury.

NOTE: Read and remove all hang tags and store with your
Operator’s Manual.

Page 9

ASSEMBLY

WARNING:

Stop the engine and disconnect the spark plug wire
before installing parts, making adjustments, cleaning, or
when not in use. Failure to do so could result in possible
serious personal injury.

ASSEMBLING THE BLOWER TUBES

See Figure 3.

 Screw the nozzle onto the blower tube and tighten

securely. Check tightness after initial run and retighten if
needed.

 Place clamp around the neck of the blower housing outlet.

Do not tighten the knob yet.

 Align the locking tab on blower tube with the slot in the

blower housing outlet; push the tube into the housing.
Twist to lock into place.

 Rotate the tube so the nozzle is pointing upward as

shown. Tighten the knob securely.

 To remove the tubes, loosen the knob on the clamp.

Rotate the tubes to unlock them; remove tube from the
blower housing outlet.

INSTALLING THE VACUUM BAG

See Figures 4 - 5.

 Remove the nozzle and blower tube from the blower.
 Unzip the vacuum bag and place the adaptor inside as

shown.

 Align the locking tab on the bag adaptor with the slot in

the blower housing outlet; push the bag adaptor into the
housing. Twist to lock into place.

 Tighten the wing nut securely.
 Rotate the vacuum bag until the shoulder strap is

upright.

 Make sure the vacuum bag is zipped and closed before

starting the unit.

NOZZLE

BAG ADAPTOR

VACUUM BAG

UPPER

BLOWER TUBE

KNOB

Fig. 3

Fig. 4

Fig. 5

Page 10

ASSEMBLY

INSTALLING THE VACUUM TUBES

See Figures 6 - 7.

To install the vacuum tubes:

 Screw the upper and lower vacuum tubes together and

tighten securely.

 Loosen the door knob on the inlet cover door and open.

Place the notch in the support arm of the upper vacuum
tube under the hinge of the inlet cover door.

 Push the upper vacuum tube into the blower housing.
 Align the upper vacuum tube knob with the hole in the

housing and tighten securely.

To remove the vacuum tubes:

 Loosen the upper vacuum tube knob.
 Remove the vacuum tubes from the blower housing.
 Close the inlet cover door and tighten the door knob

securely.

INLET COVER

DOOR

DOOR KNOB

Fig. 6

HINGE

Page 11

UPPER

VACUUM TUBE

KNOB

NOTCH IN

SUPPORT ARM

Fig. 7

WARNING:

OPERATION

FILLING THE TANK

Do not allow familiarity with tools to make you care­less. Remember that a careless fraction of a second is
sufficient to inflict serious injury.

WARNING:

Always wear safety goggles or safety glasses with
side shields when operating this tool. Failure to do
so could result in objects being thrown into your eyes
resulting in possible serious injury.

APPLICATIONS

You may use this tool for the purposes listed below:

 Clearing leaves and other debris from your lawn
 Keeping decks and driveways free from leaves and pine

needles

 Vacuuming leaves from your lawn

MIXING THE FUEL

This product is powered by a 2-cycle engine and requires
premixing gasoline and 2-cycle oil. The mixture should be at
a 50:1 ratio, using Premium Exact Mix™ 2-cycle engine oil.
If Premium Exact Mix™ 2-cycle engine oil is not available,
use a high quality 2-cycle engine oil, mixed at a 50:1 ratio.
See chart later in this section.

TO MIX THE FUEL:

 Use a clean container that is approved for use with

gasoline.

 Mix the Premium Exact Mix™ 2-cycle engine oil with

unleaded gasoline in the container, according to the
instructions on the oil package.

This engine is certified to operate on unleaded gasoline
intended for automotive use with an octane rating of 87
[(R + M) / 2] or higher. Do not use automotive oil or 2-cycle
outboard oil.

NOTE: Premium Exact Mix™ fuel mixture will stay fresh up
to 30 days. DO NOT mix quantities larger than usable in a
30 day period.

WARNING:

Gasoline is extremely flammable and explosive. A fire or
explosion from gasoline will burn you and others. Always
stop the engine before filling the fuel tank. Never add fuel
to a machine with a running or hot engine. Move at least
30 ft. from the refueling area before starting engine. Do
not smoke while filling the tank.

� Clean the surface around the fuel cap to prevent con-

tamination.
 Loosen the fuel cap slowly by turning counterclock-

wise.

 Pour the fuel mixture carefully into the tank.
 Clean and inspect the fuel cap gasket before replacing

the fuel cap.
 Replace the fuel cap and tighten it by turning it clock-

wise.

 Wipe spilled fuel from the product.
 Move at least 30 ft. away from refueling area before start-

ing the product.
NOTE: It is normal for smoke to be emitted from a new

engine during first use.

WARNING:

Check for fuel leaks. A leaking fuel cap is a fire hazard
and must be replaced immediately. If you find any leaks,
correct the problem before using the product. Failure
to do so could result in a fire that could cause serious
personal injury.

PREMIUM EXACT MIX™ (50:1)

GASOLINE OIL

1 Gallon (US) 2.6 oz.
1 Liter 20 cc (20 ml)

Page 12

OPERATION

STARTING AND STOPPING

See Figures 8 - 9.

Starting the product differs depending on whether the engine
is cold or warm.

To start a cold engine:

 Set switch to ON.
 Push the primer bulb, slowly, 8 times.
 Set the choke lever to FULL.
 Squeeze throttle trigger fully (thru next 2 steps) and pull

starter handle sharply (no more than 4 times).

 Set the choke lever to HALF.
 Pull the starter rope until the engine runs (no more than

6 times).

 Set the choke lever to RUN.
To start a warm engine:

 Set the choke lever to RUN.
 Pull the starter rope until the engine runs.

To stop:

Release the throttle trigger and push STOP on the engine
switch.

THROTTLE

TRIGGER

PRIMER BULB

CHOKE LEVER

Fig. 8

TO STOP, PUSH

“STOP” ON

ENGINE SWITCH

WARNING:

Keep away from all hot surfaces of the blower. Failure to
do so could result in possible serious personal injury.

OPERATING THE BLOWER

See Figures 10 - 11.

WARNING:

Always hold the blower away from your body, keeping
clearance between your body and the product. Any con­tact with the housing can result in burns and/or other
serious personal injury.

 Hold the blower with the upper handle in your right hand

as shown.

� To keep from scattering debris, blow around the outer

edges of a debris pile. Never blow directly into the center
of a pile.

� Operate power equipment at reasonable hours only

– not early in the morning or late at night when people
might be disturbed. Comply with the times listed in local
ordinances.

� To reduce sound levels, limit the number of pieces of

equipment used at any one time.

Fig. 9

PROPER OPERATING

POSITION

Page 13

Fig. 10

OPERATION

� Operate blower at the lowest possible throttle speed to

do the job.

�� Check your equipment before operation, especially the

muffler, air intakes, and air filters.
�� Use rakes and brooms to loosen debris before blowing.
�� In dusty conditions, slightly dampen surfaces when water

is available.
�� Watch out for children, pets, open windows or freshly

washed cars, and blow debris safely away.
�� Use the full blower nozzle extension so the air stream can

work close to the ground.
�� After using blowers or other equipment, CLEAN UP!

Dispose of debris in trash receptacles.
�� Use the wide sweeper nozzle for the everyday blowing

operation. This nozzle allows for more area to be covered

during the blowing operation.
�� The high velocity nozzle is great for wet sticky leaves. It

allows you to scrape wet leaves or debris while operating

the blower.

CRUISE CONTROL (THROTTLE LOCK)

See Figure 12.

The cruise control (throttle lock) can be used to operate the
blower without continuously holding the throttle trigger.

To engage the cruise control:

� For full throttle, depress the throttle trigger fully and slide

the cruise control selector as far forward as possible.
 To reduce engine speed, slide the cruise control selector

toward the back of the blower until the desired speed is

reached.
 To release cruise control, return the selector to the idle

position.

WIDE SWEEPER

NOZZLE

HIGH VELOCITY

NOZZLE

Fig. 11

CRUISE CONTROL
(THROTTLE LOCK)

THROTTLE TRIGGER

Page 14

Fig. 12

OPERATION

VACUUM OPERATION

See Figure 13.

 Install the vacuum tubes and bag. Refer to Installing the

Vacuum Bag and Installing the Vacuum Tubes.

 Start the blower. Refer to Starting and Stopping.
� Place the leaf bag strap over your head and onto your

left shoulder. Hold the upper handle in your right hand

and the lower handle in your left hand.
� Move the blower from side to side along outer edge of

the debris. To avoid clogging, do not place the vacuum

tube directly into the debris pile.
 Hold the engine higher than the inlet end of the vacuum

tube.
 Always point vacuum tube downhill when working on a

hillside.
� To avoid injury to the operator or unit, do not pick up

rocks, broken glass, bottles, or other similar objects.
� If the vacuum tubes should clog, stop the engine and

disconnect the spark plug wire before cleaning out the

obstruction.
 Remove the vacuum tubes and clear the debris from the

blower fan housing. Remove the bag and clear the tube.

A small rod or stick may be required to clear the entire

tube length. Ensure that all debris has been cleared before

reassembling the vacuum tubes.

Fig. 13

Page 15

MAINTENANCE

WARNING:

When servicing, use only identical replacement parts.
Use of any other parts may create a hazard or cause
product damage.

WARNING:

Always wear safety goggles or safety glasses with side
shields during power tool operation or when blowing
dust. If operation is dusty, also wear a dust mask.

GENERAL MAINTENANCE

Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.

WARNING:

REPLACING AND CLEANING THE AIR FILTER

See Figure 14.

For proper performance and long life, keep air filter clean.

 Loosen the knob on the air filter cover.
 Remove the cover.
 Remove the air filter and clean it in warm soapy water.

Rinse and let dry completely.

 Work two drops of oil into the air filter.
 Reinstall the air filter into the air filter base.
 Reinstall the cover.
 Tighten knob to secure.

NOTE: For best performance, the air filter should be
replaced annually.

BASE

Do not at any time let brake fluids, gasoline, petroleum­based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.

LUBRICATION

All of the bearings in this tool are lubricated with a sufficient
amount of high grade lubricant for the life of the unit under
normal operating conditions. Therefore, no further lubrication
is required.

KNOB

AIR FILTER

COVER

AIR FILTER

Fig. 14

Page 16

MAINTENANCE

SPARK ARRESTOR

The muffler is equipped with a spark arrestor screen inside
muffler body. After extended use the screen can become
dirty and you may need to have the muffler replaced by an
authorized servicing dealer.

WARNING:

Never run the blower without the spark arrestor in place.
Failure to do so could result in a fire that could cause
serious personal injury.

CLEANING THE EXHAUST PORT AND
MUFFLER

Depending on the type of fuel used, the type and amount
of oil used, and/or your operating conditions, the exhaust
port and muffler may become blocked with carbon deposits.
If you notice low power from the blower, have a qualified
service technician check the exhaust port and muffler for
carbon deposits. Removing the carbon deposits should
restore performance to the blower.

FUEL CAP

WARNING:

A leaking fuel cap is a fire hazard and must be replaced
immediately. Failure to do so could result in a fire that
could cause serious personal injury.

The fuel cap contains a non-serviceable filter and a check
valve. A clogged fuel filter will cause poor engine performance.
If performance improves when the fuel cap is loosened, the
check valve may be faulty or filter clogged. Replace the fuel
cap if required.

SPARK PLUG

This engine uses a Champion RCJ-6Y with 0.63 mm (0.025
in.) electrode gap. Use an exact replacement part and replace
annually.

WARNING:

Be careful not to cross-thread the spark plug. Cross­threading will seriously damage the product.

STORAGE (1 MONTH OR LONGER)

 Drain all fuel from the tank into a container approved for

gasoline. Run engine until it stops.

 Clean all foreign material from the blower. Store it in a

well-ventilated place that is inaccessible to children. Keep
away from corrosive agents such as garden chemicals
and de-icing salts.

 Abide by all Federal and local regulations for the safe

storage and handling of gasoline. Excess fuel should be
used up in other 2-cycle engine powered equipment.

ACCESSORIES

The following recommended accessories are currently available at retail stores.

Air Filter (Power Care) ............................................................................................................................................... AP04107

Spark Plug (Champion) .............................................................................................................................................. RCJ-6Y

2-Cycle Oil (Homelite) .............................................................................................................................................. AH99G01

Fuel Cap (Power Care) ............................................................................................................................................. AP04108

WARNING:

Current attachments and accessories available for use with this product are listed above. Do not use any attachments or
accessories not recommended by the manufacturer of this product. The use of attachments or accessories not recom­mended can result in serious personal injury.

Page 17

TROUBLESHOOTING

IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTACT YOUR AUTHORIZED SERVICE DEALER.

PROBLEM POSSIBLE CAUSE SOLUTION

Engine will not start 1. No spark. 1. Check spark. Remove spark plug. Reattach

the spark plug cap and lay spark plug on metal
cylinder. Pull the rope and watch for spark at
spark plug tip. If there is no spark, repeat test
with a new spark plug.

2. No fuel. 2. Push primer bulb until bulb is full of fuel. If
bulb does not fill, primary fuel delivery system
is blocked. Contact a service dealer. If primer
bulb fills, engine may be flooded, proceed to
next item.

3. Engine is flooded. 3. Set the start lever to the FULL position. Squeeze
the trigger and pull the rope repeatedly until the
engine starts and runs.

NOTE: Depending on the severity of the flooding,

this may require numerous pulls of the rope.

Engine does not reach full
speed and emits excessive
smoke

Engine starts, runs, and
accelerates but will not
idle

1. Incorrect oil/fuel mixture. 1. Use fresh fuel and the correct 2-cycle oil mix.

(50:1).

2. Air filter is dirty. 2. Clean air filter. Refer to Replacing and Cleaning

Air Filter

3. Spark arrestor screen is dirty. 3. Contact a servicing dealer.

4. Spark plug fouled. 4. Clean or replace spark plug. Reset spark plug
gap. Refer to Spark Plug Replacement

1. Idle speed screw on carburetor

needs adjustment.

1. Turn idle speed screw clockwise to increase
idle speed. See Figure 15.

.

.

Page 18

Fig. 15

WARRANTY

LIMITED WARRANTY STATEMENT

Homelite Consumer Products, Inc., (“Homelite”) warrants
to the original retail purchaser that this HOMELITE brand
outdoor product is free from defect in material and
workmanship and agrees to repair or replace, at Homelite’s,
discretion, any defective product free of charge within these
time periods from the date of purchase.

� One year for the following units: all Yard Broom, Trimlite,

and Bandit models;

� Two years if the product is used for personal, family or

household use;

� 90 days if used for any other purpose, such as

commercial or rental.

This warranty extends to the original retail purchaser
only and commences on the date of the original retail
purchase.

Any part of the this product manufactured or supplied
by Homelite and found in the reasonable judgment of
Homelite to be defective in material or workmanship will
be repaired or replaced without charge for parts and labor
by a Homelite authorized service center.

The product, including any defective part, must be returned
to an authorized service dealer within the warranty period.
The expense of delivering the product to the dealer for
warranty work and the expense of returning it back to the
owner after repair or replacement will be paid by the owner.
Homelite’s responsibility in respect to claims is limited to
making the required repairs or replacements and no claim
of breach of warranty shall be cause for cancellation or
rescission of the contract of sale of any HOMELITE brand
product. Proof of purchase will be required by the dealer
to substantiate any warranty claim. All warranty work must
be performed by a Homelite authorized service center.

This warranty is limited to ninety (90) days from the date of
original retail purchase for any HOMELITE brand product
that is used for rental or commercial purposes, or any other
income-producing purpose.

This warranty does not cover any HOMELITE brand product
that has been subject to misuse, neglect, negligence, or
accident, or that has been operated in any way contrary
to the operating instructions as specified in this operator’s
manual. This warranty does not apply to any damage to
the product that is the result of improper maintenance or
to any product that has been altered or modified. The
warranty does not extend to repairs made necessary
by normal wear or by the use of parts or accessories
which are either incompatible with the HOMELITE
brand product or adversely affect its operation,
performance, or durability. In addition, this warranty does
not cover:

A. Tune-ups – Spark Plugs, Carburetor, Carburetor

Adjustments, Ignition, Filters

B. Wear items – Bump Knobs, Outer Spools, Cutting

Lines, Inner Reels, Starter Pulleys, Starter Ropes, Drive
Belts, Tines, Felt Washers, Hitch Pins, Mulching Blades,
Blower Fans, Blower and Vacuum Tubes, Vacuum Bags
and Straps, Guide Bars, Saw Chains

Homelite reserves the right to change or improve
the design of any HOMELITE brand product without
assuming any obligation to modify any product previously
manufactured.

ALL IMPLIED WARRANTIES ARE LIMITED IN DURATION
TO THE STATED WARRANTY PERIOD. ACCORDINGLY,
ANY SUCH IMPLIED WARRANTIES INCLUDING
MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR OTHERWISE, ARE DISCLAIMED IN
THEIR ENTIRETY AFTER THE EXPIRATION OF THE
APPROPRIATE TWO-YEAR, ONE-YEAR, OR NINETY-DAY
WARRANTY PERIOD. HOMELITE’S OBLIGATION UNDER
THIS WARRANTY IS STRICTLY AND EXCLUSIVELY
LIMITED TO THE REPAIR OR REPLACEMENT OF
DEFECTIVE PARTS AND HOMELITE DOES NOT ASSUME
OR AUTHORIZE ANYONE TO ASSUME FOR THEM ANY
OTHER OBLIGATION. SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY
TO YOU. HOMELITE ASSUMES NO RESPONSIBILITY
FOR INCIDENTAL, CONSEQUENTIAL, OR OTHER
DAMAGES INCLUDING, BUT NOT LIMITED TO, EXPENSE
OF RETURNING THE PRODUCT TO AN AUTHORIZED
HOMELITE SERVICE CENTER AND EXPENSE OF
DELIVERING IT BACK TO THE OWNER, MECHANIC’S
TRAVEL TIME, TELEPHONE OR TELEGRAM CHARGES,
RENTAL OF A LIKE PRODUCT DURING THE TIME
WARRANTY SERVICE IS BEING PERFORMED, TRAVEL,
LOSS OR DAMAGE TO PERSONAL PROPERTY, LOSS
OF REVENUE, LOSS OF USE OF THE PRODUCT,
LOSS OF TIME, OR INCONVENIENCE. SOME STATES
DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY
TO YOU.

This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.

This warranty applies to all HOMELITE brand products
manufactured by or for Homelite and sold in the United
States and Canada.

To locate your nearest Homelite authorized service
center, dial 1-800-242-4672 or log on to our website at
www.homelite.com.

Page 19

WARRANTY

THE FOLLOWING CALIFORNIA AIR RESOURCES BOARD (CARB) STATEMENT ONLY APPLIES
TO MODEL NUMBERS REQUIRED TO MEET THE CARB REQUIREMENTS.

HOMELITE CONSUMER PRODUCTS, INC. LIMITED WARRANTY FEDERAL AND CALIFORNIA
EMISSION CONTROL SYSTEMS NONROAD AND SMALL OFF-ROAD ENGINES

The U.S. Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and Homelite Consumer Products,
Inc. are pleased to explain the Emission Control System Warranty on your nonroad or small off-road engine. In California, new small
off-road engines must be designed, built, and equipped to meet the state's stringent anti-smog standards. In other states, new
2000 and later model year nonroad engines must be designed, built and equipped, at the time of sale, to meet the U.S. EPA regula­tions for small nonroad engines. The nonroad engine must be free from defects in materials and workmanship which cause it to fail
to conform with U.S. EPA standards for the first two years of engine use from the date of sale to the ultimate purchaser. Homelite
Consumer Products, Inc. must warrant the emission control system on your nonroad or small off-road engine for the period of time
listed above provided there has been no abuse, neglect, or improper maintenance of your nonroad or small off-road engine.

Your emission control system may include parts such as the carburetor or fuel injection system, the ignition system, and the catalytic
converter. Also included may be hoses, belts, and connectors and other emission related assemblies.

Where a warrantable condition exists, Homelite Consumer Products, Inc. will repair your nonroad or small off-road engine at no cost
to you, including diagnosis (if the diagnostic work is performed at an authorized dealer), parts, and labor.

MANUFACTURER’S WARRANTY COVERAGE:

The 1995 and later small off road engines are warranted for two years in California. In other states, 1997 and later model year non
road engines are also warranted for two years. If any emission-related part on your engine is defective, the part will be repaired or
replaced by Homelite Consumer Products, Inc. free of charge.

OPERATOR’S WARRANTY RESPONSIBILITIES

(a) As the nonroad or small off-road engine owner, you are responsible for the performance of required maintenance listed in your

operator's manual. Homelite Consumer Products, Inc. recommends that you retain all receipts covering maintenance on your
nonroad or small off-road engine, but Homelite Consumer Products, Inc., cannot deny warranty solely for the lack of receipts
or for your failure to ensure the performance of all scheduled maintenance. Any replacement part or service that is equivalent in
performance and durability may be used in non-warranty maintenance or repairs, and shall not reduce the warranty obligations
of the engine manufacturer.

(b) As the nonroad or small off-road engine owner, you should be aware, however, that Homelite Consumer Products, Inc., may deny

you warranty coverage if your nonroad or small off-road engine or a part has failed due to abuse, neglect, improper maintenance,
or unapproved modifications.

(c) You are responsible for presenting your nonroad or small off-road engine to a Homelite Consumer Products, Inc., service dealer as

soon as a problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.

If you have any questions regarding your warranty rights and responsibilities, you should contact a Homelite Consumer Products,
Inc., Customer Representative at 1-800-242-4672.

COVERAGE:

Homelite Consumer Products, Inc. warrants to the ultimate purchaser and each subsequent purchaser that your nonroad or small
off-road engine will be designed, built, and equipped, at the time of sale, to meet all applicable regulations. Homelite Consumer
Products, Inc. also warrants to the initial purchaser and each subsequent purchaser that your nonroad or small off-road engine is
free from defects in materials and workmanship which cause the engine to fail to conform with applicable regulations for a period of
two years. The 1995 and later small off road engines are warranted for two years in California. In all other states for 1997 and later
model years, EPA requires manufacturers to warrant non-road engines for two years. These warranty periods will begin on the date
the nonroad or small off-road engine is purchased by the initial purchaser. If any emission-related part on your engine is defective,
the part will be replaced by Homelite Consumer Products, Inc. at no cost to the owner.

Homelite Consumer Products, Inc. shall remedy warranty defects at any authorized Homelite Consumer Products, Inc. engine dealer
or warranty station. Any authorized work done at an authorized dealer or warranty station shall be free of charge to the owner if
such work determines that a warranted part is defective. Any manufacturer-approved or equivalent replacement part may be used
for any warranty maintenance or repairs on emission-related parts, and must be provided free of charge to the owner if the part is
still under warranty. Homelite Consumer Products, Inc. is liable for damages to other engine components caused by the failure of
a warranted part still under warranty.

The California Air Resources Board’s Emission Warranty Parts List specifically defines the emission-related warranted parts. (EPA’s
regulations do not include a parts list, but EPA considers emission-related warranted parts to include all the parts listed below.)

These warranted parts are: Carburetor, Spark Plug, Ignition, Air Filter, and Fuel Filter.

MAINTENANCE REQUIREMENTS

The operator is responsible for the performance of the required maintenance as defined by Homelite Consumer Products, Inc. in
the operator’s manual.

LIMITATIONS

The Emission Control Systems Warranty shall not cover any of the following:
(a) repair or replacement required because of misuse or neglect, lack of required maintenance, repairs improperly performed, or

replacements not conforming to Homelite Consumer Products, Inc. specifications that adversely affect performance and/or
durability, and alterations or modifications not recommended or approved in writing by Homelite Consumer Products, Inc., and

(b) replacement of parts and other services and adjustments necessary for required maintenance at and after the first scheduled

replacement point.

The Emissions Compliance Period referred to on the Emissions Compliance label indicates the number of operating hours for which
the engine has been shown to meet Federal emission requirements. Category C=50 hours, B=125 hours, and A=300 hours.

-

Page 20

WARRANTY

CAL

L

1-800-242-4672

www.homeli

te.com

THIS PRODUCT WAS MANUFACTURED WITH A CATALYST MUFFLER
Congratulations! You have made an investment toward protecting the environment. In order to maintain this product’s

original emission level, please refer to the maintenance section below.

EMISSIONS MAINTENANCE SCHEDULE AND WARRANTED PARTS LIST

Emissions Parts Inspect Before Clean Every Replace Clean Every Replace Every
Each Use 5 Hours Every 25 Hours 25 Hours 50 Hours
or Yearly or Yearly

CATALYTIC MUFFLER ASSEMBLY ................................................................................................................... X

AIR FILTER ASSY

includes:

Filter .................................................................

SPARK SCREEN ..................................................................................................................

CARBURETOR ASSY

includes:
Heat Dam
Gaskets

FUEL TANK ASSY

includes:

Fuel Lines ........................

Fuel Cap ..........................

Fuel Filter

IGNITION ASSY

includes:

Spark Plug ........................................................................................

ALL EMISSIONS-RELATED PARTS ARE WARRANTED FOR TWO YEARS OR FOR THE PERIOD OF TIME PRIOR TO
THE PARTS FIRST SCHEDULED REPLACEMENT WHICHEVER COMES FIRST.

X
X

X ............................. X

X

X

MAKE THE MOST OF YOUR PURCHASE!

Go to www.homelite.com and register your new tool on-line.

Your product has been fully tested prior to shipment

to ensure your complete satisfaction.

For any questions about operating or maintaining

your product, call the Homelite Help Line!

To register your Homelite product or set up your eBox™ account by regular mail, please print the following infor­mation on a 3 in. x 5 in. card or standard postcard: your name, mailing address, phone numbers, email address,
Homelite product(s) purchased with item number from package, and serial number for each product. Mail the
card to: Homelite Consumer Products, Attn. Homelite Registration, 1428 Pearman Dairy Road, Anderson, SC

29625.To receive information on our company and products, please include the following statement on your
registration card: “Send me information on your products and company using the contact information I am
providing with this product registration.”

Page 21

OPERATOR’S MANUAL

VAC ATTACK II

UT08544/UT08546/UT08947

WARNING:

The engine exhaust from this product contains chemicals known to the State of California to cause
cancer, birth defects, or other reproductive harm.

CALIFORNIA PROPOSITION 65

SERVICE

For parts or service, contact your nearest Homelite authorized service dealer. Be sure to provide all
relevant information when you call or visit. For the location of the authorized service dealer nearest
you, please call 1-800-242-4672 or visit us online at www.homelite.com.

REPAIR PARTS

The model number of this product is found on a plate or label attached to the housing. Please record
the serial number in the space provided below.

MODEL NUMBER ________________________
SERIAL NUMBER ________________________

HOMELITE CONSUMER PRODUCTS, INC.

1428 Pearman Dairy Road

Anderson, SC 29625

Phone [phone]

www.homelite.com

983000-929
2-26-07 (REV:02)