Page 1
OPERATOR’S MANUAL
VAC ATTACK II
UT08542A
Your blower has been engineered and manufactured to Homelite’s high standard for dependability, ease of operation, and
operator safety. When properly cared for, it will give you years of rugged, trouble-free performance.
WARNING: To reduce the risk of injury, the user must read and understand the operator’s manual before using
this product.
Thank you for buying a Homelite product.
SAVE THIS MANUAL FOR FUTURE REFERENCE
Page 2
TABLE OF CONTENTS
n Introduction ..................................................................................................................................................................... 2
�n General Safety Rules ....................................................................................................................................................... 3
�n Specific Safety Rules....................................................................................................................................................... 4
�n Symbols........................................................................................................................................................................ 5-6
��n Features........................................................................................................................................................................ 7-8
��n Assembly ....................................................................................................................................................................9-11
�n Operation..................................................................................................................................................................12-15
�n Maintenance............................................................................................................................................................. 16-17
n Accessories ................................................................................................................................................................... 17
�n Troubleshooting ............................................................................................................................................................. 18
n Warranty ................................................................................................................................................................... 19-21
n Parts Ordering / Service ................................................................................................................................................ 22
INTRODUCTION
This product has many features for making its use more pleasant and enjoyable. Safety, performance, and dependability
have been given top priority in the design of this product making it easy to maintain and operate.
2 3
Page 3
GENERAL SAFETY RULES
WARNING:
READ AND UNDERSTAND ALL INSTRUCTIONS.
Failure to follow all instructions listed below, may result
in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS
n Do not allow children or untrained individuals to use this
unit.
n Never start or run the engine inside a closed area; breath-
ing exhaust fumes can kill.
n Wear eye protection which is marked to comply with ANSI
Z87.1 as well as hearing protection when operating this
equipment.
n Keep all bystanders, children, and pets at least 50 ft.
away.
n Wear heavy long pants, boots, and gloves. Do not wear
loose fitting clothing, short pants, jewelry of any kind, or
go barefoot.
n To reduce the risk of injury associated with objects being
drawn into rotating parts, do not wear loose clothing,
scarves, neck chains, and the like. Secure long hair so it
is above shoulder level to prevent entanglement in any
rotating parts.
n Do not operate this unit when you are tired, ill, or under
the influence of alcohol, drugs, or medication.
n Do not operate in poor lighting.
n Keep all parts of your body away from any moving parts
and all hot surfaces of the unit.
n Wear a face filter mask in dusty conditions to reduce the
risk of injury associated with the inhalation of dust.
n Check the work area before each use. Remove all objects
such as rocks, broken glass, nails, wire, or string which
can be thrown or become entangled in the machine.
n Keep firm footing and balance. Do not overreach. Over-
reaching can result in loss of balance or exposure to hot
surfaces.
n Never operate the unit without a spark arrestor screen;
this screen is located inside the muffler.
�n Product users on United States Forest Service land, and
in some states, must comply with fire prevention regulations.
n This product is equipped with a spark arrestor; however,
other user requirements may apply. Check with the federal, state, or local authorities in your area.
�n Before storing, allow the engine to cool.
�n Empty fuel tank and restrain the unit from moving before
transporting in a vehicle.
�n To reduce the risk of fire and burn injury, handle fuel with
care. It is highly flammable.
�n Do not smoke while handling fuel.
�n Mix and store fuel in a container approved for gasoline.
�n Mix fuel outdoors where there are no sparks or flames.
�n Select bare ground, stop engine, and allow to cool before
refueling.
�n Loosen fuel cap slowly to release pressure and to keep
fuel from escaping around the cap.
�n Tighten the fuel cap securely after refueling.
�n Wipe spilled fuel from the unit. Move 30 ft. away from
refueling site before starting engine.
n Never attempt to burn off spilled fuel under any circum-
stances.
�n Use only Homelite replacement parts and accessories.
Failure to do so may cause poor performance, possible
injury.
�n Maintain the unit per maintenance instructions in this
Operator’s Manual.
�n Inspect the unit before each use for loose fasteners, fuel
leaks, etc. Replace damaged parts.
Page 4
SPECIFIC SAFETY RULES
n Do not operate vacuum without vacuum bag installed;
flying debris could cause serious injury. Always close
vacuum bag completely before operating.
�n Always hold the blower in your right hand, refer to the
Operation section, later in this manual for additional
information.
�n To reduce the risk of hearing loss associated with sound
level(s), hearing protection is required.
�n Rotating impeller blades can cause severe injury. Stop
the engine before opening the vacuum door or installing /
changing tubes. Do not put hands or any other object into
the vacuum tubes while they are installed on the unit.
�n To reduce the risk of injury associated with contacting
rotating parts, stop the engine before installing or removing attachments. Do not operate without guard(s) in place.
Always disconnect the spark plug before performing
maintenance or accessing any movable parts.
�n Do not point the blower nozzle in the direction of people
or pets.
�n Never run the unit without the proper equipment
attached.
n When used as a blower, always install the blower tubes.
When used as a vacuum, always install the vacuum
tubes and vacuum bag. Make sure the vacuum bag is
completely zipped when the unit is running to avoid flying
debris.
n Avoid situations that could catch the vacuum bag on
fire. Do not operate near an open flame. Do not vacuum
warm ash from fireplaces, barbeque pits, brush piles, etc.
Do not vacuum discarded cigars or cigarettes unless the
cinders are completely cool.
4 5
Page 5
SYMBOLS
Some of the following symbols may be used on this tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer.
SYMBOL NAME DESIGNATION/EXPLANATION
Safety Alert
Read The Operator’s Manual
Eye and Hearing Protection
Long Hair
Blower Tubes
Vacuum Door
Loose Clothing
Gasoline and Oil
Precautions that involve your safety.
To reduce the risk of injury, user must read and understand
operator’s manual before using this product.
Wear eye and hearing protection when operating this equipment.
Failure to keep long hair away from the air inlet could result in
personal injury.
Do not operate without tubes in place.
Do not run unit while vacuum door is unsecured.
Failure to keep loose clothing from being drawn into air intake
could result in personal injury.
Use unleaded gasoline intended for motor vehicle use with an
octane rating of 87 [(R + M)/2] or higher. This product is powered
by a 2-cycle engine and requires pre-mixing gasoline and 2-cycle
oil.
Page 6
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated with this product.
SYMBOL SIGNAL MEANING
DANGER: Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
WARNING: Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
CAUTION: Indicates a potentially hazardous situation, which, if not avoided, may
result in minor or moderate injury.
CAUTION: (Without Safety Alert Symbol) Indicates a situation that may result in
property damage.
SERVICE
Servicing requires extreme care and knowledge and should
be performed only by a qualified service technician. For
service we suggest you return the product to your nearest
AUTHORIZED SERVICE CENTER for repair. When servicing,
use only identical replacement parts.
WARNING:
To avoid serious personal injury, do not attempt to use
this product until you read thoroughly and understand
completely the operator’s manual. Save this operator’s
manual and review frequently for continuing safe operation
and instructing others who may use this product.
WARNING:
The operation of any power tool can result in foreign objects being thrown into your eyes, which can
result in severe eye damage. Before beginning power tool operation, always wear safety goggles,
safety glasses with side shields, or a full face shield when needed. We recommend Wide Vision Safety
Mask for use over eyeglasses or standard safety glasses with side shields. Always use eye protection
which is marked to comply with ANSI Z87.1.
SAVE THESE INSTRUCTIONS
6 7
Page 7
FEATURES
PRODUCT SPECIFICATIONS
Weight ......................................................................................................................................................................... 9.8 lbs.
Engine displacement....................................................................................................................................................... 30cc
Air Velocity:
MPH...............................................................................................................................................................................200
CFM ...............................................................................................................................................................................420
HIGH VELOCITY NOZZLE
WET LEAF
SCRAPER
WIDE SWEEPER
NOZZLE
TUBE CLAMP
UPPER BLOWER TUBE
UPPER HANDLE
CRUISE CONTROL
(THROTTLE LOCK)
DOOR KNOB
THROTTLE TRIGGER
INLET COVER
DOOR
Fig. 1
Page 8
FEATURES
VACUUM BAG
SHOULDER STRAP
TUBE CLAMP
UPPER VACUUM
TUBE
LOWER VACUUM
TUBE
VACUUM BAG
ADAPTOR
ENGINE
SWITCH
VACUUM BAG
STARTER GRIP
PRIMER BULB
CHOKE LEVER
KNOW YOUR BLOWER
See Figures 1 - 2.
Before attempting to use this product, familiarize yourself
with all operating features and safety rules.
BLOWER TUBE AND NOZZLE
The blower tubes can be assembled and installed on the
blower using no tools.
CRUISE CONTROL / THROTTLE LOCK
The cruise control (throttle lock) feature allows you to operate the blower without continuously holding the throttle
trigger.
HIGH VELOCITY NOZZLE
The high velocity nozzle allows you to scrape wet leaves or
debris while operating the blower.
MOTOR
The blower has a powerful 30cc engine with sufficient power
to handle tough blowing and vacuuming jobs.
LOWER HANDLE
Fig. 2
THROTTLE TRIGGER
The blower can be operated at any speed between idle and
full throttle.
VACUUM
The blower will convert to a powerful vacuum/mulcher using
no tools.
VACUUM BAG
The vacuum bag attaches to the blower easily using the
vacuum bag adaptor.
VACUUM TUBES
The vacuum tubes can be installed on the blower without
using any tools.
WIDE SWEEPER NOZZLE
The wide sweeper nozzle allows for more area to be covered
during blower operation.
MULCHER
The blower is equipped with a mulcher feature that efficiently
reduces leaves at a 12:1 ratio.
8 9
Page 9
ASSEMBLY
UNPACKING
This product requires assembly.
n Carefully remove the tool and any accessories from the
box. Make sure that all items listed in the packing list are
included.
n Inspect the tool carefully to make sure no breakage or
damage occurred during shipping.
n Do not discard the packing material until you have care-
fully inspected and satisfactorily operated the tool.
n If any parts are damaged or missing, please call
1-800-242-4672 for assistance.
PACKING LIST
Blower
Upper Blower Tube
Wide Sweeper Nozzle
High Velocity Nozzle
Upper and Lower Vacuum Tubes
Vacuum Bag
Vacuum Bag Adaptor
Tube Clamp
2-Cycle Engine Oil
Operator’s Manual
WARNING:
If any parts are missing do not operate this tool until the
missing parts are replaced. Failure to do so could result
in possible serious personal injury.
WARNING:
Do not attempt to modify this tool or create accessories not recommended for use with this tool. Any such
alteration or modification is misuse and could result in a
hazardous condition leading to possible serious personal
injury.
NOTE: Read and remove all hang tags and store with your
Operator’s Manual.
Page 10
ASSEMBLY
WARNING:
Stop the engine and disconnect the spark plug wire
before installing parts, making adjustments, cleaning, or
when not in use. Failure to do so could result in possible
serious personal injury.
ASSEMBLING THE BLOWER TUBES
See Figure 3.
n Screw the nozzle onto the upper blower tube and tighten
securely. Check tightness after initial run and retighten if
needed.
n Place clamp around the neck of the blower housing outlet.
Do not tighten the knob yet.
n Align the locking tab on upper blower tube with the slot in
the blower housing outlet; push the tube into the housing.
Twist to lock into place.
n Rotate the tube so the nozzle is pointing upward as
shown. Tighten the knob securely.
n To remove the tubes, loosen the knob on the clamp.
Rotate the tubes to unlock them; remove tube from the
blower housing outlet.
INSTALLING THE VACUUM BAG
See Figures 4 - 5.
n Remove the nozzle and upper blower tube from the
blower.
n Unzip the vacuum bag and place the adaptor inside as
shown.
n Align the locking tab on the bag adaptor with the slot in
the blower housing outlet; push the bag adaptor into the
housing. Twist to lock into place.
n Tighten the wing nut securely.
n Rotate the vacuum bag until the shoulder strap is
upright.
n Make sure the vacuum bag is zipped and closed before
starting the unit.
NOZZLE
ADAPTOR
VACUUM BAG
UPPER
BLOWER TUBE
KNOB
Fig. 3
Fig. 4
Fig. 5
10 11
Page 11
ASSEMBLY
INSTALLING THE VACUUM TUBES
See Figures 6 - 7.
TO INSTALL THE VACUUM TUBES:
n Screw the upper and lower vacuum tubes together and
tighten securely.
n Loosen the door knob on the inlet cover door and open.
Place the notch in the support arm of the upper vacuum
tube under the hinge of the inlet cover door.
n Push the upper vacuum tube into the blower housing.
n Align the upper vacuum tube knob with the hole in the
housing and tighten securely.
TO REMOVE THE VACUUM TUBES:
n Loosen the upper vacuum tube knob.
n Remove the vacuum tubes from the blower housing.
n Close the inlet cover door and tighten the door knob
securely.
INLET COVER
DOOR
DOOR KNOB
Fig. 6
HINGE
UPPER
VACUUM TUBE
KNOB
NOTCH IN
SUPPORT ARM
Fig. 7
Page 12
WARNING:
OPERATION
FILLING THE TANK
Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is
sufficient to inflict serious injury.
WARNING:
Always wear safety goggles or safety glasses with
side shields when operating this tool. Failure to do
so could result in objects being thrown into your eyes
resulting in possible serious injury.
APPLICATIONS
You may use this tool for the purposes listed below:
n Clearing leaves and other debris from your lawn
n Keeping decks and driveways free from leaves and pine
needles
MIXING THE FUEL
This product is powered by a 2-cycle engine and requires
premixing gasoline and 2-cycle oil. The mixture should be at
a 50:1 ratio, using Premium Exact Mix™ 2-cycle engine oil.
If Premium Exact Mix™ 2-cycle engine oil is not available,
use a high quality 2-cycle engine oil, mixed at a 50:1 ratio.
See chart later in this section.
TO MIX THE FUEL:
n Use a clean container that is approved for use with
gasoline.
n Mix the Premium Exact Mix™ 2-cycle engine oil with
unleaded gasoline in the container, according to the
instructions on the oil package.
This engine is certified to operate on unleaded gasoline
intended for automotive use with an octane rating of 87
[(R + M) / 2] or higher. Do not use automotive oil or 2-cycle
outboard oil.
NOTE: Premium Exact Mix™ fuel mixture will stay fresh up
to 30 days. DO NOT mix quantities larger than usable in a
30 day period.
WARNING:
Gasoline is extremely flammable and explosive. A fire or
explosion from gasoline will burn you and others. Always
stop the engine before filling the fuel tank. Never add fuel
to a machine with a running or hot engine. Move at least
30 ft. from the refueling area before starting engine. Do
not smoke while filling the tank.
�n Clean the surface around the fuel cap to prevent con-
tamination.
n Loosen the fuel cap slowly by turning counterclock-
wise.
n Pour the fuel mixture carefully into the tank.
n Clean and inspect the fuel cap gasket before replacing
the fuel cap.
n Replace the fuel cap and tighten it by turning it clock-
wise.
n Wipe spilled fuel from the product.
n Move at least 30 ft. away from refueling area before start-
ing the product.
NOTE: It is normal for smoke to be emitted from a new
engine during first use.
WARNING:
Check for fuel leaks. A leaking fuel cap is a fire hazard
and must be replaced immediately. If you find any leaks,
correct the problem before using the product. Failure
to do so could result in a fire that could cause serious
personal injury.
PREMIUM EXACT MIX™ (50:1)
GASOLINE OIL
1 Gallon (US) 2.6 oz.
1 Liter 20 cc (20 ml)
12 13
Page 13
OPERATION
STARTING AND STOPPING
See Figure 8.
Starting the product differs depending on whether the engine
is cold or warm.
TO START A COLD ENGINE:
n Place the blower on a flat, bare surface.
n Make sure cruise control is locked in the IDLE position.
Do not engage the throttle trigger or cruise control during
the start-up process.
n Push the primer bulb, slowly, 7 times.
n Move the choke lever to the full choke position marked
START.
n Pull the starter rope until the engine runs.
n Allow the engine to run 15 seconds, then engage the
throttle trigger to begin operation.
TO START A WARM ENGINE:
n Move the choke lever to the full choke position marked
START.
n Pull the starter rope until the engine runs.
TO STOP:
See Figure 9.
Release the throttle trigger and push STOP on the engine
switch.
THROTTLE
TRIGGER
PRIMER BULB
CHOKE LEVER
Fig. 8
TO STOP, PUSH
“STOP” ON
ENGINE SWITCH
OPERATING THE BLOWER
See Figures 10 - 11.
WARNING:
Always hold the blower away from your body, keeping
clearance between your body and the product. Any contact with the housing can result in burns and/or other
serious personal injury.
n Start the blower, refer to Starting and Stopping earlier
in this manual. Hold the blower with the upper handle in
your right hand as shown.
�n To keep from scattering debris, blow around the outer
edges of a debris pile. Never blow directly into the center
of a pile.
�n Operate power equipment at reasonable hours only
– not early in the morning or late at night when people
might be disturbed. Comply with the times listed in local
ordinances.
�n To reduce sound levels, limit the number of pieces of
equipment used at any one time.
Fig. 9
PROPER OPERATING
POSITION
Fig. 10
Page 14
OPERATION
�n Operate blower at the lowest possible throttle speed to
do the job.
��n Check your equipment before operation, especially the
muffler, air intakes, and air filters.
��n Use rakes and brooms to loosen debris before blowing.
��n In dusty conditions, slightly dampen surfaces when water
is available.
��n Conserve water by using power blowers instead of hoses
for many lawn and garden applications, including areas
such as gutters, screens, patios, grills, porches, and
gardens.
��n Watch out for children, pets, open windows or freshly
washed cars, and blow debris safely away.
��n Use the full blower nozzle extension so the air stream can
work close to the ground.
��n After using blowers or other equipment, CLEAN UP!
Dispose of debris in trash receptacles.
��n Use the wide sweeper nozzle for the everyday blowing
operation. This nozzle allows for more area to be covered
during the blowing operation.
��n The high velocity nozzle is great for wet sticky leaves. It
allows you to scrape wet leaves or debris while operating
the blower.
CRUISE CONTROL (THROTTLE LOCK)
See Figure 12
The Cruise Control (throttle lock) can be used to operate the
blower without continuously holding the throttle trigger.
TO ENGAGE THE CRUISE CONTROL:
�n For full throttle, depress the throttle trigger fully and slide
the cruise control selector as far forward as possible.
n To reduce engine speed, slide the cruise control selector
toward the back of the blower until the desired speed is
reached.
n To release cruise control, return the selector to the idle
position.
VACUUM OPERATION
See Figure 13.
n Install the vacuum tubes and bag. Refer to Installing the
Vacuum Bag and Installing the Vacuum Tubes earlier
in this manual.
n Start the blower. Refer to Starting and Stopping earlier
in this manual.
n� Place the leaf bag strap over your head and onto your
left shoulder. Hold the upper handle in your right hand
and the lower handle in your left hand.
�n Move the blower from side to side along outer edge of
the debris. To avoid clogging, do not place the vacuum
tube directly into the debris pile.
WIDE SWEEPER
NOZZLE
HIGH VELOCITY
NOZZLE
Fig. 11
CRUISE CONTROL
(THROTTLE LOCK)
THROTTLE TRIGGER
Fig. 12
14 15
Page 15
OPERATION
n Hold the engine higher than the inlet end of the vacuum
tube.
n Always point vacuum tube downhill when working on a
hillside.
�n To avoid injury to the operator or unit, do not pick up
rocks, broken glass, bottles, or other similar objects.
�n If the vacuum tubes should clog, stop the engine and
disconnect the spark plug wire before cleaning out the
obstruction.
n Remove the vacuum tubes and clear the debris from the
blower fan housing. Remove the bag and clear the tube.
A small rod or stick may be required to clear the entire
tube length. Ensure that all debris has been cleared before
reassembling the vacuum tubes.
Fig. 13
Page 16
MAINTENANCE
WARNING:
When servicing, use only identical Homelite replacement
parts. Use of any other parts may create a hazard or
cause product damage.
WARNING:
Always wear safety goggles or safety glasses with side
shields during power tool operation or when blowing
dust. If operation is dusty, also wear a dust mask.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by their use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
WARNING:
REPLACING AND CLEANING THE AIR FILTER
See Figure 14.
For proper performance and long life, keep air filter clean.
n Push down on the latch of the air filter cover; carefully
pull the top of the air filter cover so it pivots away from
the base.
n Remove the air filter and clean it in warm soapy water.
Rinse and let dry completely.
n Reinstall the air filter into the air filter base.
n Pivot the cover back in place. Push the latch back into
the slot and ensure the cover is locked in place.
NOTE: For best performance, the air filter should be
replaced annually
AIR FILTER
BASE
Do not at any time let brake fluids, gasoline, petroleumbased products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
injury.
LUBRICATION
All of the bearings in this tool are lubricated with a sufficient
amount of high grade lubricant for the life of the unit under
normal operating conditions. Therefore, no further lubrication
is required.
LATCH
AIR FILTER
COVER
Fig. 14
16 17
Page 17
MAINTENANCE
SPARK ARRESTOR
The muffler is equipped with a spark arrestor screen inside
muffler body. After extended use the screen can become
dirty and you may need to have the muffler replaced by an
authorized servicing dealer.
WARNING:
Never run the blower without the spark arrestor in place.
Failure to do so could result in a fire that could cause
serious personal injury.
CLEANING THE EXHAUST PORT AND
MUFFLER
Depending on the type of fuel used, the type and amount
of oil used, and/or your operating conditions, the exhaust
port and muffler may become blocked with carbon deposits.
If you notice low power from the blower, have a qualified
service technician check the exhaust port and muffler for
carbon deposits. Removing the carbon deposits should
restore performance to the blower.
FUEL CAP
WARNING:
A leaking fuel cap is a fire hazard and must be replaced
immediately. Failure to do so could result in a fire that
could cause serious personal injury.
The fuel cap contains a non-serviceable filter and a check
valve. A clogged fuel filter will cause poor engine performance.
If performance improves when the fuel cap is loosened, the
check valve may be faulty or filter clogged. Replace the fuel
cap if required.
SPARK PLUG
This engine uses a Champion RCJ-6Y with 0.63 mm (0.025
in.) electrode gap. Use an exact replacement part and replace
annually.
WARNING:
Be careful not to cross-thread the spark plug. Crossthreading will seriously damage the product.
STORAGE (1 MONTH OR LONGER)
n Drain all fuel from the tank into a container approved for
gasoline. Run engine until it stops.
n Clean all foreign material from the blower. Store it in a
well-ventilated place that is inaccessible to children. Keep
away from corrosive agents such as garden chemicals
and de-icing salts.
n Abide by all Federal and local regulations for the safe
storage and handling of gasoline. Excess fuel should be
used up in other 2-cycle engine powered equipment.
ACCESSORIES
The following recommended accessories are currently available at retail stores.
Air Filter (Power Care)............................................................................................................................................... AP04107
Spark Plug (Champion) .............................................................................................................................................. RCJ-6Y
2-Cycle Oil (Homelite).............................................................................................................................................. AH99G01
WARNING:
Current attachments and accessories available for use with this product are listed above. Do not use any attachments or
accessories not recommended by the manufacturer of this product. The use of attachments or accessories not recommended can result in serious personal injury.
Page 18
TROUBLESHOOTING
IF THESE SOLUTIONS DO NOT SOLVE THE PROBLEM CONTACT YOUR AUTHORIZED SERVICE DEALER.
PROBLEM POSSIBLE CAUSE SOLUTION
Engine will not start
Engine does not reach full
speed and emits excessive
smoke
1. No spark.
2. No fuel.
3. Engine is flooded.
1. Incorrect oil/fuel mixture.
2. Air filter is dirty.
3. Spark arrestor screen is dirty.
4. Spark plug fouled.
1. Check spark. Remove spark plug. Reattach
the spark plug cap and lay spark plug on metal
cylinder. Pull the rope and watch for spark at
spark plug tip. If there is no spark, repeat test
with a new spark plug.
2. Push primer bulb until bulb is full of fuel. If
bulb does not fill, primary fuel delivery system
is blocked. Contact a service dealer. If primer
bulb fills, engine may be flooded, proceed to
next item.
3. Set the start lever to the START position.
Squeeze the trigger and pull the rope repeatedly until the engine starts and runs.
NOTE : Depending on the severity of the flood-
ing, this may require numerous pulls of the
rope.
1. Use fresh fuel and the correct 2-cycle oil mix.
(50:1).
2. Clean air filter. Refer to “Replacing and Cleaning Air Filter” earlier in this manual.
3. Contact a servicing dealer.
4. Clean or replace spark plug. Reset spark
plug gap. Refer to “Spark Plug Replacement”
earlier in this manual.
Engine starts, runs, and
accelerates but will not idle
1. Idle speed screw on carburetor
needs adjustment.
1. Turn idle speed screw clockwise to increase
idle speed. See Figure 15.
Fig. 15
18 19
Page 19
WARRANTY
LIMITED WARRANTY STATEMENT
Homelite Consumer Products, Inc. warrants to the original
retail purchaser that this HOMELITE product is free from
defect in material and workmanship and agrees to repair or
replace, at Homelite Consumer Products, Inc.’s discretion,
any defective product free of charge within these time
periods from the date of purchase.
n� One year for the following units: All Yard Broom, Trimlite
and Bandit;
n� Two years if the product is used for personal, family or
household use;
�n 90 days, if used for any other purpose, such as
commercial or rental.
This warranty extends to the original retail purchaser
only and commences on the date of the original retail
purchase.
Any part of the HOMELITE product manufactured or
supplied by HOMELITE and found in the reasonable
judgment of HOMELITE to be defective in material or
workmanship will be repaired or replaced by an authorized
HOMELITE service dealer without charge for parts and
labor.
The product, including any defective part, must be returned
to an authorized service dealer within the warranty period.
The expense of delivering the HOMELITE product to the
dealer for warranty work and the expense of returning it
back to the owner after repair or replacement will be paid by
the owner. HOMELITE’S responsibility in respect to claims
is limited to making the required repairs or replacements
and no claim of breach of warranty shall be cause for
cancellation or rescission of the contract of sale of any
HOMELITE product. Proof of purchase will be required by
the dealer to substantiate any warranty claim. All warranty
work must be performed by an authorized HOMELITE
service dealer.
This warranty is limited to ninety (90) days from the date
of original retail purchase for any HOMELITE product that
is used for rental or commercial purposes, or any other
income-producing purpose.
This warranty does not cover any HOMELITE product
that has been subject to misuse, neglect, negligence, or
accident, or that has been operated in any way contrary
to the operating instructions as specified in this operator’s
manual. This warranty does not apply to any damage to
the HOMELITE product that is the result of improper
maintenance or to any HOMELITE product that has
been altered or modified. The warranty does not extend
to repairs made necessary by normal wear or by the use
of parts or accessories which are either INCOMPATIBLE
WITH THE HOMELITE product or adversely affect its
operation, performance, or durability.
In addition, this warranty does not cover:
A. Tune-ups – Spark Plugs, Carburetor, Carburetor
Adjustments, Ignition, Filters
B. Wear items – Bump Knobs, Outer Spools, Cutting Lines,
Inner Reels, Starter Pulleys, Starter Ropes, Drive Belts,
Tines, Felt Washers, Hitch Pins, Mulching Blades, Blower
Fans, Blower and Vacuum Tubes, Vacuum Bags and
Straps, Guide Bars, Saw Chains
HOMELITE reserves the right to change or improve the
design of any HOMELITE product without assuming
any obligation t o modify any product previously
manufactured.
ALL IMPLIED WARRANTIES ARE LIMITED IN DURATION
TO THE STATED WARRANTY PERIOD. ACCORDINGLY,
AN Y SUC H IMP LIED WARRANTI ES IN CLUDI NG
MERCHANTABILITY, FITNESS FOR A PARTICULAR
PURPOSE, OR OTHERWISE, ARE DISCLAIMED IN
THEIR ENTIRETY AFTER THE EXPIRATION OF THE
APPROPRIATE TWO-YEAR, ONE-YEAR, OR NINETY DAY
WARRANTY PERIOD. HOMELITE’S OBLIGATION UNDER
THIS WARRANTY IS STRICTLY AND EXCLUSIVELY
LIMITED TO THE REPAIR OR REPLACEMENT OF
DEFECTIVE PARTS AND HOMELITE DOES NOT ASSUME
OR AUTHORIZE ANYONE TO ASSUME FOR THEM ANY
OTHER OBLIGATION. SOME STATES DO NOT ALLOW
LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY
LASTS, SO THE ABOVE LIMITATION MAY NOT APPLY
TO YOU. HOMELITE ASSUMES NO RESPONSIBILITY
FOR INCIDENTAL, CONSEQUENTIAL, OR OTHER
DAMAGES INCLUDING, BUT NOT LIMITED TO, EXPENSE
OF RETURNING THE HOMELITE PRODUCT TO AN
AUTHORIZED SERVICE DEALER AND EXPENSE OF
DELIVERING IT BACK TO THE OWNER, MECHANIC’S
TRAVEL TIME, TELEPHONE OR TELEGRAM CHARGES,
RENTAL OF A LIKE PRODUCT DURING THE TIME
WARRANTY SERVICE IS BEING PERFORMED, TRAVEL,
LOSS OR DAMAGE TO PERSONAL PROPERTY, LOSS
OF REVENUE, LOSS OF USE OF THE PRODUCT, LOSS
OF TIME, OR INCONVENIENCE. SOME STATES DO
NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE
ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY
TO YOU.
This warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
This warranty applies to all HOMELITE products
manufactured by HOMELITE and sold in the United
States and Canada.
To locate your nearest service dealer, dial 1-800-242-4672
or log on to our website at www.homelite.com.
Page 20
WARRANTY
THE FOLLOWING CALIFORNIA AIR RESOURCES BOARD (CARB) STATEMENT ONLY APPLIES
TO MODEL NUMBERS REQUIRED TO MEET THE CARB REQUIREMENTS.
HOMELITE CONSUMER PRODUCTS, INC., LIMITED WARRANTY FEDERAL AND CALIFORNIA
EMISSION CONTROL SYSTEMS NONROAD AND SMALL OFF-ROAD ENGINES
The U.S. Environmental Protection Agency (EPA), the California Air Resources Board (CARB), and Homelite Consumer Products, Inc., are
pleased to explain the Emission Control System Warranty on your nonroad or small off-road engine. In California, new small off-road engines
must be designed, built and equipped to meet the state’s stringent anti-smog standards. In other states, new 2000 and later model year
nonroad engines must be designed, built, and equipped at the time of sale to meet the U.S. EPA regulations for small nonroad engines. The
nonroad engine must be free from defects in materials and workmanship which cause it to fail to conform with U.S. EPA standards for the
first two years of engine use from the date of sale to the ultimate purchaser. Homelite Consumer Products, Inc., must warrant the emission
control system on your nonroad or small off-road engine for the period of time listed above provided there has been no abuse, neglect, or
improper maintenance of your nonroad or small off-road engine.
Your emission control system may include parts such as the carburetor or fuel injection system, the ignition system, the catalytic converter.
Also included may be hoses, belts and connectors, and other emission-related assemblies.
Where a warrantable condition exists, Homelite Consumer Products, Inc., will repair your nonroad or small off-road engine at no cost to you,
including diagnosis (if the diagnostic work is performed at an authorized dealer), parts, and labor.
MANUFACTURER’S WARRANTY COVERAGE:
The 1995 and later small off road engines are warranted for two years in California. In other states, 1997 and later model year nonroad
engines are also warranted for two years. If any emission-related part on your engine is defective, the part will be repaired or replaced by
Homelite Consumer Products, Inc., free of charge.
OWNER’S WARRANTY RESPONSIBILITIES
(a) As the nonroad or small off-road engine owner, you are responsible for the performance of required maintenance listed in your operator’s
manual. Homelite Consumer Products, Inc., recommends that you retain all receipts covering maintenance on your nonroad or small
off-road engine, but Homelite Consumer Products, Inc., cannot deny warranty solely for the lack of receipts or for your failure to ensure
the performance of all scheduled maintenance. Any replacement part or service that is equivalent in performance and durability may be
used in non-warranty maintenance or repairs, and shall not reduce the warranty obligations of the engine manufacturer.
(b) As the nonroad or small off-road engine owner, you should be aware, however, that Homelite Consumer Products, Inc., may deny you
warranty coverage if your nonroad or small off-road engine or a part has failed due to abuse, neglect, improper maintenance, or unapproved modifications.
(c) You are responsible for presenting your nonroad or small off-road engine to a Homelite Consumer Products, Inc., service dealer as soon
as a problem exists. The warranty repairs should be completed in a reasonable amount of time, not to exceed 30 days.
If you have any questions regarding your warranty rights and responsibilities, you should contact a Homelite Consumer Products, Inc.,
Customer Representative at 1-800-242-4672.
COVERAGE:
Homelite Consumer Products, Inc., warrants to the ultimate purchaser and each subsequent purchaser that your nonroad or small off-road
engine will be designed, built, and equipped at the time of sale to meet all applicable regulations. Homelite Consumer Products, Inc., also
warrants to the initial purchaser and each subsequent purchaser that your nonroad or small off-road engine is free from defects in materials
and workmanship which cause the engine to fail to conform with applicable regulations for a period of two years. The 1995 and later small
off road engines are warranted for two years in California. In all other states for 1997 and later model years, EPA requires manufacturers to
warrant non-road engines for two years. These warranty periods will begin on the date the nonroad or small off-road engine is purchased
by the initial purchaser. If any emission-related part on your engine is defective, the part will be replaced by Homelite Consumer Products,
Inc., at no cost to the owner.
Homelite Consumer Products, Inc., shall remedy warranty defects at any authorized Homelite Consumer Products, Inc., engine dealer or
warranty station. Any authorized work done at an authorized dealer or warranty station shall be free of charge to the owner if such work
determines that a warranted part is defective. Any manufacturer-approved or equivalent replacement part may be used for any warranty
maintenance or repairs on emission-related parts, and must be provided free of charge to the owner if the part is still under warranty. Homelite
Consumer Products, Inc., is liable for damages to other engine components caused by the failure of a warranted part still under warranty.
The California Air Resources Board’s Emission Warranty Parts List specifically defines the emission-related warranted parts. (EPA’s regulations do not include a parts list, but EPA considers emission-related warranted parts to include all the parts listed below.)
These warranted parts are: Carburetor, Spark Plug, Ignition, Air Filter, and Fuel Filter.
MAINTENANCE REQUIREMENTS
The owner is responsible for the performance of the required maintenance as defined by Homelite Consumer Products, Inc., in the operator’s
manual.
LIMITATIONS
The Emission Control Systems Warranty shall not cover any of the following:
(a) repair or replacement required because of misuse or neglect, lack of required maintenance, repairs improperly performed, or replace-
ments not conforming to Homelite Consumer Products, Inc., specifications that adversely affect performance and/or durability, and
alterations or modifications not recommended or approved in writing by Homelite Consumer Products, Inc., and
(b) replacement of parts and other services and adjustments necessary for required maintenance at and after the first scheduled replacement
point.
The Emissions Compliance Period referred to on the Emissions Compliance label indicates the number of operating hours for which the
engine has been shown to meet Federal emission requirements. Category C=50 hours, B=125 hours, and A=300 hours.
20 21
Page 21
WARRANTY
1-8 00- 242 -46 72
CALL
THIS PRODUCT WAS MANUFACTURED WITH A CATALYST MUFFLER
Congratulations! You have made an investment toward protecting the environment. In order to maintain this product’s
original emission level, please refer to the maintenance section below.
EMISSIONS MAINTENANCE SCHEDULE AND WARRANTED PARTS LIST
Emissions Parts Inspect Before Clean Every Replace Clean Every Replace Every
Each Use 5 Hours Every 25 Hours 25 Hours 50 Hours
or Yearly or Yearly
CATALYTIC MUFFLER ASSEMBLY ................................................................................................................... X
AIR FILTER ASSY
includes:
Filter ................................................................. X............................. X
SPARK SCREEN .................................................................................................................. X
CARBURETOR ASSY
includes:
Heat Dam
Gaskets
FUEL TANK ASSY
includes:
Fuel Lines........................ X
Fuel Cap.......................... X
Fuel Filter
IGNITION ASSY
includes:
Spark Plug........................................................................................ X
ALL EMISSIONS RELATED PARTS ARE WARRANTED FOR TWO YEARS OR FOR THE PERIOD OF TIME PRIOR TO
THE PARTS FIRST SCHEDULED REPLACEMENT WHICHEVER COMES FIRST.
CALL US FIRST
For any questions about operating or maintaining your product,
call the Homelite® Help Line!
Your product has been fully tested prior to shipment to ensure
your complete satisfaction.
Page 22
OPERATOR’S MANUAL
VAC ATTACK II
UT08542A
WARNING:
The engine exhaust from this product contains chemicals known to the State of California to cause
cancer, birth defects, or other reproductive harm.
CALIFORNIA PROPOSITION 65
SERVICE
For parts or service, contact your nearest Homelite authorized service dealer. Be sure to provide all
relevant information when you call or visit. For the location of the authorized service dealer nearest
you, please call 1-800-242-4672 or visit us online at www.homelite.com.
REPAIR PARTS
The model number of this product is found on a plate or label attached to the housing. Please record
the serial number in the space provided below.
MODEL NUMBER ________________________
SERIAL NUMBER ________________________
UT08542A
HOMELITE CONSUMER Products, Inc.,
1428 Pearman Dairy Road, Anderson, SC 29625
Post Office Box 1207, Anderson, SC 29622
Phone 1-800-242-4672
www.homelite.com
983000-781
5-05
Loading...