THIS INSTRUCTION BOOKLET CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.
‐ Unit can tip over causing severe injury or death.
‐ Anchor unit to stud in wall (if instructed to).
‐ Do Not allow children to climb on unit.
‐ Put heavy items on lower shelves or drawers.
Easy
Tough
Assembly Di�culty Meter
Helpful Hints
PEOPLE NEEDED FOR ASSEMBLY: 1 - 2
ESTIMATED ASSEMBLY TIME: 1 HOUR
‐ Identify, sort and count the parts before attempting assembly.
‐ Compression dowels are lightly tapped in with a hammer.
‐ Slides are labeled with a R (right) and L (left) for proper placement.
‐ Make sure to always face the point on the top of the Cam Lock towards
the outer edge.
‐ Use all the nails provided for the back panel and spread them out
equally.
‐ Back panel must be used to make sure your unit is sturdy.
‐ Do NOT use harsh chemicals or abrasive cleaners on this item.
‐ Never push, pull, or drag your furniture.
‐ Open your item in the area you plan to keep it to avoid excessive heavy
lifting.
Before You Start
‐
‐
‐
‐
Installation is very difficult, please two people
to install
Read through each step carefully and follow the
proper order
Separate and count all your parts and hardware
Give yourself enough room for the assembly
process
‐
‐
please be aware to slow down and stop when screw
is tight.
Failure to do so may result in stripping the
screw.
Have the following tools: Hammer
Caution: If using a power drill or power
screwdriver for screwing,
A
B
C
D
D1
D1
×8
D2
D2
×8
3.5*40 3.5*4015*11.5
×26 ×44 ×28
mm mm mm
E F1 F2 H
×16
F1:3.5*14mm ×43
F2: mm ×163 .5 * 4 0
Drawer rails
G
×24*18 mm
I J L
×16 ×2
×4×2 ×1 ×2
×8
×4
MK1 K2
1
2 3
Parts assembly diagram
All asterisks follow the installation process above
Plate splitting diagram
3
14
14
19
2
4
15
8
8
8
8
6
7
18
12
5
17
11
7
10
18
17
12
13
16
9
9
9
1
9
installation drawing 1
B
J
15*11.5
3.5*40mm
1
7
mm
×20
×16
18
D
M
F1
×16
F1: mm ×23 .5 *14
G
×2
First put J into the corresponding
1
hole of No. 18/12 board, then put D
2
into the corresponding hole of No.
4
18/12 board to lock, and finally
lock A with B
4*18 mm
×2
I
×2
2
18
7
12
3
16
18
12
7
Push 16 plate into the slots of the 18 ,12 plates
18
4
5
18
7
7
12
17
17
12
Fix M and back of plate 17 with F1
Fix I and in front of plate 17 with G
installation drawing 2
F1
F1: ×163 .5 *14
D
4
D1
×8
5
Back section of part D
D
Fix D on the inside of No.5 plate with F1
installation drawing 3
A
3.5*40
mm
×4
B
15*11.5
mm
5
×4
C
3.5*40
mm
8
8
8
8
×16
Connect plate 8 and plate 5 with A and C
respectively, and then lock A with B for fixation
8
8
4
8
8
Connect plate 8 and plate 4 with A and C
respectively, and then lock A with B for fixation
installation drawing 4
A
3.5*40
mm
×2
B
15*11.5
mm
×2
C
3.5*40
mm
×1
2
Connect plate 2 and plate 4 with A and C, and lock plate A with B
2
14
14
Push the two 14 plates into the slots of the 2 plate
installation drawing 5
A
3.5*40
mm
×8
B
15*11.5
mm
×8
C
3.5*40
mm
×4
3
Connect plate 3 and plate 1 with A and C, and lock plate A with B
1
Use A and C to connect the previously connected part
with No. 1 board, and then use B to lock A and fix it
installation drawing 6
A
3.5*40
mm
×2
6
B
15*11.5
1
mm
×2
C
3.5*40
mm
×1
Connect plate 6 and plate 1 with A and C, and lock plate A with B
15
6
Push 15 plate into board 6 and slot 4
installation drawing 7
×6
B
15*11.5
mm
×6
A C
3.5*40
mm
3.5*40
mm
×4
G
×4
Fixed glass door with G connection
19
Use A, C and D to connect the No. 19 board with the previously
installed part, and then use B to lock A and fix it
installation drawing 8
F1
3.5*40
mm
×25
K1 K2
×4
×2
L
×1
2
1
Fix the K1,K2 under the No.1 board with F1
Fix the L under the No.2 board with F1
installation drawing 9
A
3.5*40
mm
×4
B
15*11.5
mm
×4
C
3.5*40
mm
×2
F2
F3:3.5* 4 0 ×16
10
9
10
Use F2 to connect and fix No. 10 board and No. 11，13 board
9
11
16
16
13
mm
13
10
F1
Push 16 plate into the slot
of two 11 boards
F1
Connect plate 9 and plate 11,13 with
A and C, and lock plate A with B
D1
Front section of part D
Precautions:When installing the drawer
slide,Need to split the slide rail into
two parts，D1 and D2.Look at the arrow
direction and press down to pull out
the slide rail
1
119
1
2
2-3mm
Disassembly method of drawer slide rail
D2
When installing the
slide rail,reserve a
distance of 2-3mm from
the bottom of the
9 ，11 , 13 board.
D1
D2
Drawer rails Press the arrow to toggle
the buckle, and then pull
out the track.
D1
installation drawing 10
Align the slide rail of the drawer with the
slide rail of the cabinet and push it forward
If you have any questions about the product,
please do not hesitate to contact customer service.
5 Star Rating
Visit your local retailer’s website,rate your purcha sed
product and leave us some feedback!
We would like to extend a big "Thank You" to all of
our customers for taking the time to assemble this
FAFA&GAGA product, and to give us your
valuable feedback.
Loading...