MINI OIL FILLED RADIATORS
USER INSTRUCTIONS
Model : ACHO700W
TECHNICAL CHARACTERISTICS
MINI OIL FILLED RADIATORS
RATED POWER INPUT: 700W
RATED VOLTAGE RANGE: 240V~ 50Hz
IMPORTANT Read these instructions fully before using the heater. Retain
these instructions for future reference.
NOTE:- THESE HEATERS ARE INTENDED FOR DOMESTIC USE ONLY
ASSEMBLY OF THE HEATER
Fit the separate foot to the radiator by pushing it
firmly onto the control panel and end fin as shown
in the diagram. Check the stability of the heater by
standing it on a smooth level surface.
Fitting the foot to the Heater (Refer to the right fig.)
Parts
1. Power Switch
2. Thermostat Knob
3. Handle
4. Oil Filled Fins
5. Separate Foot
SAFETY INSTRUCTIONS (to be read before operating the heater)
1. This appliance is not intended for use by persons (including children) with
reduced physical, sensory or mental capabilities, or lack of experience and
knowledge, unless they have been given supervision or instruction concerning use
of the appliance by a person responsible for their safety.
2. Children should be supervised to ensure that they do not play with the
appliance.
3. The product is for household use only.
4. Connect the appliance to single phase AC supply of the voltage specified on the
rating plate.
5. In order to avoid overheating, do not cover the heater.
6. Never leave the heater unattended whilst in use. Always turn the heater to the
OFF position and unplug it from the electrical outlet when not in use.
7. Extreme caution is necessary when any heater is used by or near children,
invalids or elderly people and whenever the heater is left operating and
unattended.
8. The heater must not be located immediately below an electrical socket-outlet.
9. Do not run cord under carpeting and do not cover cord with throw rugs, runners
or the like. Arrange cord away from traffic area and where it will not be tripped
over.
10. Do not operate the heater with a damaged cord or plug, or after the heater
malfunctions, has been dropped, or damaged in any manner.
11. If the supply cord is damaged, it must be replaced by the manufacturer or its
service agent or a similarly qualified person to avoid a hazard.
12. Avoid the use of an extension cord as this may overheat and cause a risk of
fire.
13. Use the heater in a well-ventilated area. Do not insert or allow objects to enter
any ventilation or exhaust opening. To prevent a possible fire, do not block air
intakes or exhaust openings in any manner. Do not use on soft surfaces, like a
bed, where openings may become blocked. Use the heater on flat, dry surfaces
only.
14. Do not place this heater near flammable materials, surfaces or substances, as
there may be a risk of fire. Keep the above flammable materials, surfaces or
substances at least 1m from the front of the product and keep them away from the
sides and rear.
15. Do not use the heater in any areas where petrol, paint or other flammable
liquids are stored e.g. Garages or workshops.
16. Don’t use this heater in the immediate surroundings of a bath, a shower or a
swimming pool. Never locate the heater where it may fall into bathtub or other
water container.
17. This heater is hot when in use. To avoid burns and personal injury, do not let
bare skin touch hot surfaces. If provided, use handles when moving the product.
18. Make sure that no other appliances are in use on the same electrical circuit as
your product as an overload can occur.
19. This heater is filled with a precise quantity of special oil.
20. Repairs that require opening of the oil container are only to be made by the
manufacturer or his service agent who should be contacted if there is an oil
leakage.
21. Regulations concerning the disposal of oil when scrapping the appliance have
to be followed.
22. The heater should not be used in a room, of which the floor area is less than 5
M2.
23. The cord shouldn’t be placed nearby the hot surface of the appliance.
OPERATION OF THE HEATER
NOTE 1:- When the heater is turned on for the first time or after having not been
used for a long period, it may emit some smells and fumes. These will disappear
when the heater has been on a short while.
1) Choose a suitable location for the heater, taking into account the safety
instructions above.
2) Insert the plug of the heater into a suitable socket.
3) Turn the thermostat knob fully in a clockwise direction to the maximum
setting.
4) Turn on the heating element by means of the power switch on the side panel.
When the heating element is on the power switch will illuminate.
5) When the desired room temperature has been reached, the thermostat knob
should be turned slowly anti-clockwise until the thermostat is heard to click
off and the light on the power switch is seen to go out. After this the heater
will keep the air temperature in the room at the set temperature by switching
on and off automatically.
CLEANING THE HEATER
1) Always un-plug the heater from the wall socket and allow it to cool down
before cleaning.
2) Clean the outside of the heater by wiping with a damp cloth and buff with a
dry cloth. Do not use any detergents or abrasives and do not allow any water
to enter the heater.
STORING THE HEATER
When the heater is not used for long periods of time it should be protected from
dust and stored in a clean dry place.
Declaration of Conformity
We ACL Group (Int.)Ltd, England. DN6 8LZ declare that the Homefront Oil
Filled Radiator has been manufactured according to our full quality assurance
procedures.
The declaration is to certify that it conforms to CE, WEEE, EMC and RoHS
directives:
Environmental Protection
RECYCLING
WASTE ELECTRICAL PRODUCTS SHOULD NOT BE DISPOSED
OF WITH HOUSEHOLD WASTE. PLEASE RECYCLE WHERE
FACILITIES EXIST. CHECK WITH YOUR LOCAL AUTHORITY OR
RETAILER FOR RECYCLING ADVICE.
Loading...