Home Easy HE420 User Manual

HOME

easy

RE-INVENTING THE HOME

HE-410 & HE-420 IP56

Remote outdoor socket

and Switch

The HomeEasy Outdoor Socket kit
allows you to control your outdoor
lighting and ponds etc simply and
easily.
The remote control outdoor socket can
be set to operate in one of three
settings:

AUTO: Allows the remote control outdoor socket to
switch on/off using the remote control, allowing
you to control your outdoor lighting from any point.

ON: Sets the remote control outdoor socket as a
standard outdoor socket.
USE THIS OPTION WHEN USING GARDEN
MACHINERY SUCH AS A LAWNMOWER OR
HEDGECUTTERS.

OFF: An additional safety feature of the HE410 is the ability to
switch off the power to the unit as per a normal socket.

1 Gang

Remote Switch

V1.0

2 Gang

Remote Socket

Opening Unit:

1. Open up the front, flip top cover.

3. After all 4 screws have
been removed, the front will
separate from the back.

2. Unscrew the four screws shown. To
separate the front, from the back of the
unit.

Front half

Back half

Wiring Remote Socket:

On the back half of the remote socket you will see that there are 4 circular shaped disks
(‘Entry blanks’) on each side (3 are plastic, 1 is rubber). Depending on if you wish to link up
more than one ‘Outdoor remote socket’ you can remove or replace these disks.

It is recommended that the bottom most ‘Entry blank’ should be removed to gain entry
into the ‘Outdoor Remote Socket’ . This will help keep the moisture out.

If installing the outdoor socket with conduit from the sides or top attachment, a 5mm hole
must be drilled through the bottom left drainage hole. This will allow for any condensation
forming in the conduit, to drain out.
Caution: opening the drainage hole will effect the IP rating of the product. Ensure that
jetted water is not directly sprayed onto the unit.

Do Not drill out the drainage hole when installing the
Outdoor socket into a dusty environment. Always install
the unit via the bottom cable entry, making sure that a
5mm hole is drilled into the lowest point in the conduit

1. Switch off and isolate the mains power before altering
the code setting

2: Cut back the cable to reveal 3 separate wires
L= Live  Brown
E= Earth  Green & Yellow
N= Neutral  Blue

3. Now strip each wire, exposing 10mm of its

(Live - Brown)
(Earth - Green & Yellow)
(Neutral - Blue)

Exposed wire

Remove Bottom

'Entry Blank'

When installing secondary Outdoor receiver sockets always place the
units approximately 30-40cm apart.

INSTALLATION WARNING:

ON INSTALLATION TURN OFF YOUR MAINS

ELECTRIC SUPPLY

This product should be fitted by a competent person in accordance with the
instructions listed below and with the relavent clauses of the IEE wiring
regulations BS7671.

The remote outdoor socket should be used in conjunction with a fused spur
connection, all connections to the socket need to be made as instructed,
making sure that the cable used is appropriate for the installation
environment, free from stress & terminals are tightened fully.

Mounting Socket:

1: In the back half of the unit, in all four corners are purpose made holes for fixing your
remote socket to your intended surface. TheHE-410 needs to be mounted onto a flat,
vertical surface. Free from grease, loose material and any corrosive substances.
We recommend a house or sturdy garden wall.

2. Using the back half of the unit as a template, pencil mark all four
corners onto your chosen surface. Making sure 'TOP' (marked on
the casing is at the top.

3. Drill all four marked holes and insert suitable wall plugs for a
number ‘8’ screw (recommended size).

Fixing Holes

4. Screw to the wall.

4. Send the cable through the conduit and into the
‘Outdoor Remote Socket’.

(L = Live - Brown)
(E = Earth - Green & Yellow)
(N = Neutral - Blue)

3: Insert the exposed core wires into their related
terminals and clamp down by tightening the
respective screw. If you are not using 3 core wire:

 L= Live  Brown
 E= Earth  Green & Yellow
 N= Neutral  Blue

LEN

(FIG.8)

LEN

Please Note: The Cable is
up inside the box, s o that
no wires can be seen.

WARNING:

You MUST install an earth cable between the origin of the installation and the earth
terminal of the outdoor socket. This must be insulated inside a sleeve protector within
the conduit.
If using metal conduit, earth continuity must be maintained between conduits.Seal
Conduit and conduit entry with a non setting conduit sealant. Contact your local
electrical retailer.

Switch Installation:

Remove the switch unit from the protective casing, attach the
casing to the wall using the screws and wall plugs provided.
Reinsert the switch unit into the protective casing making sure
the unit is the correct way up.

WARNING: attaching the outdoor switch to a metallic surface will reduce the
operating distance.

Deleting Remote Control:

To delete a remote control that has been paired with an outdoor receiver socket,
simply press the "Learn" button. The LED will start to blink; press the off button on the
remote control, the LED will blink twice to confirm that the remote control has been
removed from the receiver sockets memory.

Remote Socket reset:

To delete all the remote control units from the memory of the receiver socket, hold
the "Learn" button for more than 6 seconds, the LED will start to blink continuously.
Press the learn button again, the LED will blink twice to confirm the deletion of all
remote controls form the receiver memory.

Changing Battery:

Remove the switch unit from the protective casing, using a small screwdriver
remove the front cover of the switch unit.

Help Section :

Help: Occasionally interference from adjacent receiver sockets and low voltage

products (Transformers) can affect the operating range.
Always Try to locate addition outdoor sockets a minimum of 30cm apart.

RF Range: The radio signals operating distance is reduced when the signal has to

pass through walls. The radio signals achieve a range of 30 metres line of sight; this
can be reduced depending on the type of material and localised interference.

Product Operation:

Pairing/Deleting with Remote Control:

Up to Six remote control units can be paired with each outdoor socket. To pair the
switch and socket together, press the "Learn" button. The LED will start to flash, now
press the selected "On" button on the remote control, the LED will stop flashing. The
units are now paired together, you can test this by pressing the selected "ON/OFF"
button.

Switch 1 Switch 2

On

Off

Always refer to the original instruction when using with additional products.

Replace the battery with a new CR2032 battery
(Byron SX100), making sure the polarity is correct.

Replace the front cover and reinsert the switch unit into the protective enclosure.

Product Specification:

Remote Control: HE-410
Input: 230V ~50Hz
Range: 30 Metres (Open Distance)
Frequency: 433.92MHz

Remote Control: HE-401/402
Input: CR2032 Battery
Range: 30 Metres (Open Distance)

Frequency: 433.92MHz
Max Load: 3000W (Resistive)
IP56 (Lid Clip closed)

Warning: Never Exceed the Product Specification

Contact:   Helpline: 0845 2301 231

Contact Details:

C H Byron
34, Sherwood Rd
Aston Fields
Bromsgrove
B60 3DR

Tel: [phone]
Fax: [phone]
Web: www.chbyron.com
E-mail:
[e-mail]

433MHz

R&TTE

APPROVED

A

IRL

B
DK
FIN

F

D

GR

LT

CH Byron Electrical United Kingdom. www.chbyron.com

I

L

NL

P
E
S

0560

UK
BG
CZ
EST

H
IS

LV

SLO
CH

RO

M
N

SK

PL