Home Easy HE207 User Manual
HOME
easy
The HE-207 Indoor PIR adds extra
security and ease of use to your Home
Easy products
-Selectable timer setting
-Selectable Detection Range
-Variable Light setting
-25 Metre Wire Free Range
-Battery Powered 2*AAA
-100W Max Load
(Incandescent Lights only)
HE-207 Remote control
RE-INVENTING THE HOME
Indoor PIR Kit
V1.0
2. The base unit can be attached to the wall using either the adhesive strips or
screws (Included).
3. Replace the two front covers.
Pairing/Deleting with Remote Control:
Resetting Remote Control:
To delete all the remote control units from the memory of the receiver
module, hold the "Learn" button for more than 6 seconds, the LED will start
to blink continuously. Press the learn button again, the LED will blink twice to
confirm the deletion of all remote controls from the receiver memory.
Detection Area
Detection Range:
The Indoor PIR has 3 selectable detection ranges: 1, 3 or 6 Metres.
To alter the detection range, remove the front cover and move the slide switch
to the required setting.
The HE-207 allows you to control your HE205 Bulb Holder via a wire free
PIR sensor. When the PIR beam is broken the indoor PIR will switch on the light
for 5 seconds to 10 minutes
Compatible with all Home Easy products.
Installation:
The HomeEasy Indoor PIR can be placed in any location, even in bathrooms.
Only use the adhesive strip on suitable surfaces.
Avoid placing the PIR in direct sunshine, above direct heat sources or on
metallic surfaces.
1. Using a small screwdriver remove the front cover and base plate.
Up to Six remote control units can be paired with each
HomeEasy Receiver socket or module, to pair the indoor
PIR with a receiver unit, remove the front cover and,
slide the switch to DEL.
Now press the "Learn" button, the LED will start to flash, then slide the
"LEARN" switch to "SET", the units are now paired together.
Learn
Deleting Remote Control:
To delete the PIR from the memory of a HomeEasy receiver socket or module
control. Simply press the "Learn" button, the LED will start to blink; slide the
"LEARN" switch to "DEL", the LED will blink twice to confirm that the remote
control has been removed from the receiver sockets memory.
6M 6M 6M
3M 3M 3M
1M 1M 1M
1.0
Height (PIR)
1 2 3 4 5 6 7 8
Detection Range (Metres)
Day/Night Setting:
elp S
H
ec
tion :
6M 6M 6M
1.5
3M 3M 3M
1M 1M 1M
Height (PIR)
1 2 3 4 5 6 7 8
Detection Range (Metres)
Detection Angle:
The PIR detection area is 65 degrees, this can be reduced using the clip-on
covers (included). if required the covers can be cut to size.
The PIR can operate one of three setting depending upon the ambient light
Level, to alter the light setting remove the front cover and use the slide switch
to select the setting.
PIR will operate 24Hrs a day
PIR will operate between 4pm to 6am
PIR will operate between 6pm to 6am
Times are approximations only
Changing Batteries:
1. Unclip the front cover from the front of the PIR
using a small screw driver.
2. Remove the batteries and replace using 2
new 'AAA' batteries, making sure the polarity
is correct.
No Activation: Check the battery level and polarity, replace with new
batteries if necessary
Receiver Stays: The PIR may be suffering from false activation, try
ON Continuously adjusting the position and detection angle.
RF Range: The radio signals operating distance is reduced when the signal
has to pass through walls. The radio signals achieve a range of 25m; this can
be reduced depending on the type of material.
Range
Reduction Guide:
BRICK
10 - 40%
METAL
PLASTICS
10 - 15%
GLASS
CONCRETE
40- 80%
TIMBER
.
e
z
i
if r
equ
ed the c
r
i
an be cut t
s c
er
v
o
o s
Setting Timer :
The HomeEasy indoor PIR will switch on the
receiver socket or module for a predefined
period of time, this can be set between 5seconds
and10 minutes.
To select the time period, remove the front cover
and slide the switch to the required timer
setting.
5Sec
1Min
5
10min
Always dispose of old batteries in a
environmentally responsible way
3. Replace the front cover making sure the clips are correctly aligned and
firmly push the case together.
Product Specification:
Remote Control: HE-303
Battery: 2 * AAA
Range: 25Metres (Open Distance)
Frequency: 433.92MHz
Indoor Use Only
Receiver Module: HE-205
Input:230V ~50Hz
Range: 30 Metres (Open Distance)
Max Load: 100W (Incandescent)
Frequency: 433.92MHz
Indoor Use Only
90%
Contact: Helpline: 0845 2301 231
Contact Details:
C H Byron
34, Sherwood Rd
Aston Fields
Bromsgrove
B60 3DR
Tel: 0845 2301231
Fax: 01527 57701
Web: www.chbyron.com
E-mail:
support@chbyron.com
5 - 15%
APPROVED
A
B
DK
FIN
F
D
GR
LT
CH Byron Electrical United Kingdom. www.chbyron.com
10 - 40%
R&TTE
IRL
I
L
NL
P
E
S
433MHz
0560
UK
BG
CZ
EST
H
IS
LV
SLO
CH
RO
M
N
SK
PL
Loading...