HoMedics vende sus productos con la intención de que no tengan defectos de fabricación ni de mano de
obra por un plazo de un año a partir de la fecha de compra original, con las siguientes excepciones.
HoMedics garantiza que sus productos no tendrán defectos de material ni de mano de obra bajo condiciones
de uso y servicio normales. Esta garantía se extiende únicamente a consumidores y no a distribuidores.
Para obtener servicio para su producto HoMedics, envíe por correo el producto y su recibo de compra fechado (como comprobante de compra), con franqueo pago, a la siguiente dirección:
HoMedics Consumer Relations
Service Center Dept. 168
3000 Pontiac Trail
Commerce Township, MI 48390
No se aceptarán pagos contra entrega.
HoMedics no autoriza a nadie, incluyendo, pero sin limitarse a, distribuidores, posteriores consumidores
compradores del producto a un distribuidor, o compradores remotos, a obligar a HoMedics de forma alguna
más allá de las condiciones aquí establecidas. La garantía de este producto no cubre daños causados por
uso inadecuado o abuso, accidente, conexión de accesorios no autorizados, alteración del producto, instalación inadecuada, reparaciones o modificaciones no autorizadas, uso inadecuado de la fuente de
energía/electricidad, cortes de energía, caída del producto, funcionamiento incorrecto o daño de una pieza de
funcionamiento debido al no cumplimiento del mantenimiento recomendado por el fabricante, daños durante
el transporte, robo, descuido, vandalismo, condiciones climáticas, pérdida de uso en el período durante el
cual el producto está en una instalación de reparación o a la espera de piezas o reparación, o cualquier otra
condición, sin importar cual sea, que se encuentre fuera del control de HoMedics.
Esta garantía es válida únicamente si el producto es comprado y operado en el país en el cual se compró el
producto. Un producto que requiera modificaciones o adaptación para habilitar su funcionamiento en
cualquier país que no sea aquél para el que fue diseñado, fabricado, aprobado y/o autorizado, o la reparación
de productos dañados por estas modificaciones no están cubiertos bajo esta garantía.
LA GARANTÍA AQUÍ ESTABLECIDA SERÁ LA ÚNICA Y EXCLUSIVA GARANTÍA. NO HABRÁ NINGUNA OTRA
GARANTÍA EXPRESA NI IMPLÍCITA, INCLUYENDO NINGUNA GARANTÍA DE COMERCIALIZACIÓN O APTITUD
NI NINGUNA OTRA OBLIGACIÓN POR PARTE DE LA COMPAÑÍA CON RESPECTO A PRODUCTOS CUBIERTOS
POR ESTA GARANTÍA. HOMEDICS NO TENDRÁ RESPONSABILIDAD ALGUNA POR NINGÚN DAÑO INCIDENTAL, CONSECUENTE NI ESPECIAL. BAJO NINGÚN CONCEPTO ESTA GARANTÍA REQUERIRÁ MÁS QUE LA
REPARACIÓN O CAMBIO DE ALGUNA PIEZA O PIEZAS QUE SE HALLEN DEFECTUOSAS DENTRO DEL
PERÍODO DE VIGENCIA DE ESTA GARANTÍA. NO SE EFECTUARÁN REEMBOLSOS. SI NO HAY PIEZAS DE
REPUESTO DISPONIBLES PARA LOS MATERIALES DEFECTUOSOS, HOMEDICS SE RESERVA EL DERECHO
DE REALIZAR SUSTITUCIONES EN VEZ DE REPARAR O CAMBIAR.
Esta garantía no se extiende a la compra de productos abiertos, usados, reparados, embalados otra vez y/o
abiertos y vueltos a cerrar, incluyendo entre otras cosas la venta de dichos productos en sitios de r
Internet y/o la venta de dichos productos por revendedores o mayoristas. Todas y cada una de las garantías
cesarán y terminarán inmediatamente con respecto a cualquier producto o pieza del mismo que estén reparados, cambiados, alterados o modificados sin el consentimiento previo explícito y por escrito de HoMedics.
Esta garantía le proporciona derechos legales específicos. Es posible que usted tenga derechos adicionales
que pueden variar de un país a otro. Debido a las regulaciones de ciertos países, es posible que algunas de
las limitaciones y exclusiones no se apliquen en su caso.
Por más información con respecto a nuestra línea de productos en los EE.UU., visítenos en:
derechos. HoMedics® es una marca registrada de HoMedics, Inc. y sus compañías
afiliadas. SoundSpa™ es una marca comercial de HoMedics Inc. y sus compañías
O
emate por
www.homedics.com
afiliadas. Reservados todos los derechos.
IB-SS5000B
El manual en español empieza
a la página 17
CLOCK RADIO SOUND MACHINE WITH
TIME PROJECTION & TEMPERATURE READING
™
SOUNDSPA
PREMIER
Instruction Manual and
Warranty Information
SS-5000
Create your perfect sleep environment.
Thank you for purchasing SoundSpa Premier, the HoMedics acoustic relaxation
machine. This, like the entire HoMedics product line, is built with high-quality
craftsmanship to provide you years of dependable service. We hope that you will
find it to be the finest product of its kind. SoundSpa helps create your perfect
sleep environment. Fall asleep to any of its six calming sounds, then wake to
sound, radio or alarm. SoundSpa can also mask distractions to improve your
concentration while you read, work or study.
IMPORTANT SAFETY INSTRUCTIONS:
When using an electrical appliance, basic precautions should always
be followed, including the following:
READ ALL INSTRUCTIONS BEFORE USING
Caution: All
servicing of
this product
must be
performed by
authorized
HoMedics
Service
Personnel only.
• Never operate this appliance if it has a damaged cord, plug,
cable or housing. If it is not working properly, if it has been
dropped or damaged, return it to Homedics Service Center for
examination and repair.
• Keep cord away from heated surfaces.
• Never drop or insert any object into any opening.
• Do not operate where aerosol (spray) products are being used or
where oxygen is being administered.
• Do not carry this appliance by power cord or use cord as handle.
• To disconnect, remove plug from outlet.
• This appliance is designed for indoor use only. Only the remote
sensor should be used outdoors.
• Only set on dry surfaces. Do not place on surface wet from water
or cleaning
DANGER
• Always unplug the appliance from the electrical outlet immediately before cleaning.
• Do not reach for an appliance that has fallen into water. Unplug it immediately.
• Do not place or store appliance where it can fall or be pulled into a tub or sink.
Do not place in or drop into water or other liquid.
WARNING
- To reduce the risk of electric shock:
- To reduce the risk of burns, fire, electric shock or injury to
persons:
• Close supervision is necessary when this appliance is used by or near children,
invalids or disabled persons.
• Use this appliance only for its intended use as described in this manual. Do not
use attachments not recommended by HoMedics; specifically any attachments
not provided with the unit.
2
SAVE THESE INSTRUCTIONS
Caution – Please read all instructions
carefully before operating.
• Never leave the appliance unattended, especially if children
are present.
• Never cover the appliance when it is in operation.
• This unit should not be used by children without adult supervision.
• Always keep the cord away from high temperature and fire.
• Do not lift, carry, hang, or pull the product by the power cord.
• If the adaptor sustains damage, you must stop using this product
immediately and contact the HoMedics Service Center. (See the
warranty section for the HoMedics address.)
• Three gentle-wake options - radio, alarm or soothing sound
• Easy-to-read LCD display
• Projection feature projects time and temperature on the
ceiling or wall
• Auto-timer lets you choose how long you listen - 15, 30, or
60 minutes
• Volume control adjusts the volume of the radio, beep, or sounds
4
Figure 4
C/F Button
Projector
On/Off Switch
DC Jack
FM/AM Switch
Antenna
ow/Off Button
Atomic
On/Off Button
DST/T
ime Zone
Backlight High/L
5
Assembly and Instructions for Use
1. Unpack the product and check to make sure everything is included (Fig 1).
2. This unit is powered by a DC adaptor.
3. The battery power is designed only to provide MEMORY BACK-UP for the clock
and alarm settings. Three “AAA” batteries (not included) should be inserted into
the battery compartment if memory back-up is desired (in the event of power
outages or if the unit is unplugged). The time will be illuminated on the clock
display, however, the backlight will not be illuminated and all other functions of
the unit will be unavailable. As soon as the power supply returns, the display will
indicate the correct time, and the functions will become available again.
NOTE: Battery must be installed in order for clock memory back-up to
operate. In the event of a power failure or disconnection, if the battery is
not installed, the clock and alarm will need to be re-set when power is
restored.
4. To install batteries, remove compartment cover. Insert three “AAA” batteries into
the compartment on the bottom of the unit according to the polarity direction
indicated. Replace cover and snap into place.
5. Attach the adaptor into the DC jack on the base of the unit (Fig 3) and insert the
cord into a 120V household outlet.
Setting Time
Using the Atomic Time
The National Institute of Standard and Technology (NIST) in Fort Collins, Colorado
broadcasts the time signal (WWVB at 60kHz AM radio signal) with an accuracy of 1
second per every 3,000 years. The signal will cover a distance up to 2,000 miles from
the source. Like a typical AM radio, your Atomic Clock will not able to receive the
WWVB signal in places surrounded by heavy concrete or metal panels. The reception
of the time signal can be affected by mobile phones, TV, electrical appliances or
other electronic interference. To get the best performance of the Atomic clock, please
install the home receiver (SoundSpa Premier) near a window and away from large
metallic objects. If the unit is not working properly, change its position. There may
be some interference at this location. The Sound Spa Premier will start synchronizing
the clock to the Pacific Time Zone as soon as the unit is plugged in.
Selecting a Time Zone
1. Press the ATOMIC ON/OFF button (Fig. 3) to turn off the atomic time function.
To indicate you are at the off position, the atomic time icon (Fig. 2) will be
removed from the display.
2. Toggle through the DST/TIME ZONE button (Fig. 3) until you reach your desired
time zone. (P - Pacific Standard Time, M - Mountain Standard Time, C - Central
Standard Time, E - Eastern Standard Time)
3. Once you have selected your time zone, press the ATOMIC ON/OFF button
again to turn on the atomic time function. To indicate you are at the on position,
the atomic time time icon will reappear with flashing antenna bands. (When the
antenna bands appear flashing the unit is searching for the atomic time signal.)
4. If the atomic time icon disappears afterwards, the atomic time signal is not available
at that moment. Try setting the unit in other locations. Remember to place the unit
away from sources of interference such as mobile phones, appliances, TV etc.
5. The atomic time icon will appear on screen if the atomic time reception is successful.
(The antenna bands will stop flashing when atomic time reception is successful.)
The radio-controlled clock will have a daily synchronization at 1:00 am everyday.
If previous attempts of reception were unsuccessful, the home receiver will
attempt synchronization each hour until successful. Each reception cycle ranges
from 2 - 10 minutes.
Manual Setting of Clock
1. Press the HOUR button (Fig 1) until you reach the correct hour.
2. Press the MIN button (Fig 1) until you reach the correct minute.
3. Press the BACKLIGHT HI/LOW/OFF button (Fig 3) to adjust the backlight intensity.
Note: A PM indicator will appear in the upper left hand corner of the LCD
display during the PM hours. Be sure to set the time for the correct 12-hour
period - AM (morning) or PM (evening).
67
Listening to Nature Sounds
1. Select the sound you wish to listen to and press
the corresponding button (Fig 5).
2. To adjust the volume, turn the VOLUME knob
(Fig 1) to your desired level.
3. When finished listening to the sounds you may
turn them off by pressing the POWER button, or
switch to the radio by pressing RADIO (Fig 4).
Note: When the unit is turned on it will
always default to the last mode used.
Listening to the Radio
1. Press the RADIO button (Fig. 4).
2. Use the AM/FM switch located on the back of the unit (Fig. 3) to change
between bands.
3. Rotate the TUNER (Fig. 1) to select a radio station.
4. To adjust the volume turn the VOLUME knob (Fig 1) to your desired level.
5. When finished listening to the radio you may turn it off by pressing the
POWER button. (Fig. 4)
Note: Adjust the antenna on the back of the unit to better the radio
reception if needed.
Using the Auto-Timer
When the power is on and you are listening to a nature sound or the radio
you may set a timer so the unit will automatically turn off.
1. Toggle through the TIMER button (Fig 4) until the corresponding green
LED illuminates next to the time of your choice, 15, 30 or 60 minutes.
2. To cancel the timer, toggle through the TIMER button until the green LED
light is not illuminated, which indicates you are at the off position or press
POWER (Fig. 4).
Figure 5
Setting and Using The Alarm
Setting and using Alarm 1 or Alarm 2 (Individually)
1. Slide the alarm switch to ALARM 1 or Alarm 2. (Fig. 3) An ALARM BELL (Fig. 2)
icon will appear on the LCD display.
2. Press the ALARM SET button. (Fig 4.) The time will flash.
3. While the time is flashing press the HOUR button (Fig 1) until you reach the correct
hour. Then press the MIN button (Fig 1) until you reach the desired minute.
4. After 5 seconds the alarm set time will stop flashing and it will be programmed,
or you may press the ALARM SET button to confirm.
Note: The PM indicator also applies to the alarm. You can review the alarm
setting anytime by pressing the ALARM SET button.
5. You may choose one of 3 wake options; BEEP, SOUND, or RADIO by pressing
the ALARM MODE button. A green LED will appear next to the wake mode
selected. (Fig. 4)
NOTE: When using the sound mode, the unit will set to the last sound you
listened to. If you wish to change it press the sound you wish to wake to
(Fig. 5) and then press the POWER button (Fig 4).
6. When the alarm sounds you may:
a. SNOOZE: Press the SNOOZE button (Fig 1). Your sleep time will be
extended by 9 minutes. You may use this feature until you turn the
alarm off.
b. RESET: Turn the alarm off by pressing ANY button on the unit, except
for the SNOOZE button (Fig 4). The alarm clock will automatically
reset for the next day in its current mode. The ALARM BELL icon and
green LED will remain displayed to indicate the alarm is set. If you wish to
change the wake mode follow step 5 under Setting and Using Alarm 1
and Alarm 2 Individually.
c. OFF: To completely turn off the alarm so it is not set for the next day,
slide the alarm switch to OFF.
NOTE: If the alarm sounds for 30 minutes continuously it will automatically
turn off.
89
Loading...
+ 11 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.