• This warranty does not cover damage caused by misuse or abuse; accident; the attachment of
any unauthorized accessory; alteration to the product; improper installation; unauthorized
repairs or modifications; improper use of electrical/power supply; loss of power; dropped product;
malfunction or damage of an operating part from failure to provide manufacturer's recommended
maintenance; transportation damage; theft; neglect; vandalism; or environmental conditions;
loss of use during the period the product is at a repair facility or otherwise awaiting parts or
repair; or any other conditions whatsoever that are beyond the control of HoMedics.
• Damage incurred due to shipping and handling does not constitute a defect under this warranty.
• HoMedics is not responsible in any way for losses, damages, or inconvenience caused by
equipment failure.
• HoMedics shall not be responsible for any type of incidental, consequential, indirect, or special
damages.
• All implied warranties, including but not limited to those implied warranties of fitness and
merchantability, are limited in the total duration of one year from the original purchase date.
• HoMedics' sole liability and the purchaser's exclusive remedy shall be for the repair
HoMedics' option, for the replacement of the defective part.
• Notwithstanding the above, if replacement parts for defective materials are not available,
HoMedics reserves the right to make substitutions in lieu of repair or replacement.
This warranty provides you with specific legal rights. You may have additional rights, which may
vary from state to state. Because of individual state regulations, some of the above limitations
and exclusions may not apply to you.
• Always unplug the appliance from the electrical outlet immediately after using and
before cleaning.
• DO NOT reach for an appliance that has fallen into water. Unplug it immediately.
• Do not use while bathing or showering.
WARNING
- TO REDUCE THE RISK OF ELECTROCUTION:
- TO REDUCE THE RISK OF BURNS,
ELECTROCUTION, FIRE OR INJURY TO PERSONS:
• An appliance should never be left unattended when plugged in. Unplug from outlet
when not in use and before putting on or taking off parts or attachments.
• Close supervision is necessary when this appliance is used by, on or near children,
invalids or disabled persons.
• Use this appliance only for its intended use as described in this manual. Do not use
attachments not recommended by HoMedics; specifically any attachments not provided
with the unit.
• NEVER operate this appliance if it has a damaged cord or plug, if it is not working
properly, if it has been dropped or damaged, or dropped into water. Return it to
HoMedics Service Center for examination and repair.
• NEVER use pins or other metallic fasteners with this appliance.
• Keep cord away from heated surfaces.
• NEVER block the air openings of the appliance. Keep air openings free of lint, hair, etc.
• NEVER use while sleeping or fall asleep while using the massager.
• NEVER drop or insert any object into any opening.
• DO NOT operate where aerosol (spray) products are being used or where oxygen is
being administered.
• Connect this appliance to a properly grounded outlet only. See Grounding Instructions.
• DO NOT operate under a blanket or pillow. Excessive heating can occur and cause
fire, electrocution or injury to persons.
• DO NOT carry this appliance by supply cord or use cord as handle.
• To disconnect, turn all controls to the “off ” position, then remove plug from outlet.
• This appliance is designed for household use only.
• This appliance is designed for personal, non-professional use only. This appliance
should be used only for personal, non-professional uses. Any other use will void warranty.
SAVE THESE INSTRUCTIONS
23
Grounding Pin
Adapter
Metal Screw
Figure A
Tab for
Grounding
Screw
Figure B
Grounded
Outlet
Figure C
Figure D
Figure E
Grounding Instructions
This product must be grounded. If it should malfunction or
breakdown, grounding provides a path of least resistance
for the electric current to reduce the risk of electric shock.
This product is equipped with a cord having an equipmentgrounding conductor and a grounding plug. The plug must
be plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local codes
and ordinances.
DANGER
Improper connection of the equipment-grounding
conductor can result in a risk of electric shock.
Check with a qualified electrician or ser
if you are in doubt as to whether the product is
properly grounded. Do not modify the plug provided
with the product - if it will not fit the outlet, you
may temporarily use an adaptor (such as the
one shown in Figure B) until you have a proper
outlet (such as the one shown in Figure C)
installed by a qualified electrician.
This product is for use on a nominal 120-volt circuit, and
has a grounding plug that looks like the plug illustrated in
Figure A. A temporary adapter that looks like the adapter
illustrated in Figure B may be used to connect this plug to
a 2-pole receptacle as shown in Figure D if a properly
grounded outlet is not available. The temporary adapter
should be used only until a properly grounded outlet FigureC can be installed by a qualified electrician. The tab for
grounding screw Figure B extending from the adapter
must be connected to a permanent ground such as a
properly grounded outlet box cover. Whenever the adapter
is used, it must be held in place by a metal screw. See
Figures D and E.
viceman
Caution — Please read all instructions carefully
before operating.
• This product is not intended for medical use. It is
intended only to provide a luxurious massage.
• If you have any concerns regarding your health consult
your doctor before using this product.
• Those with the following conditions should consult their
physician prior to using this massage chair:
a) Malignant tumor
b) Heart Disease
c) Pregnancy
d) Conditions requiring rest
e) Back Disease or back trouble from an injury or accident.
f) Diabetes
• Individuals with pacemakers should consult a doctor
before use.
• Never leave the appliance unattended, especially if children
are present.
• Never cover the appliance when it is in operation.
• Do not use this product for more than 20 minutes at a time.
• Extensive use could lead to the products excessive heating
and shorter life. Should this occur, discontinue use and
allow the unit to cool before operating.
• Never use this product directly on swollen or inflamed
areas or skin eruptions.
• Do not use this product as a substitute for medical
attention.
• This product should never be used by any individual
suffering from any physical ailment that would limit the
user’s capacity to operate the controls.
• This product should never be used by any individual
suffering from any ailments that would limit or altogether
inhibit the user’s capacity to feel or have any sensation in
the body part that the product is being used on.
• If you detect a malfunction or any other abnormal condition
in the operation of your chair, turn off the power immediately
and disconnect the power cord from the outlet.
• Should you have a power failure, turn the power switch
to the OFF position.
• If the chair has gotten wet or liquid is spilled near the
main power switch, turn the chair off, unplug it from the
wall socket and call HoMedics Consumer Relations.
• Do not use the massager while standing on a damp floor
or when any part of the body is in contact with plumbing
or any similar ground.
• Do not use unit if noise above normal sound is heard.
45
Figure 1
Figure 2
Figure 3
Assembly Instructions
Setting up your massage chair is easy to do. Your massage
chair is almost completely assembled. After carefully removing
all the contents from the packaging, inspect the chair and
its components to make sure everything has been received.
Components:
• Chair back
• Chair seat
• Seat cushion
Step 1
Attaching the Seat Cushion
• First, clip the ties holding the power cord to the back of
the seat frame.
• Next, attach the seat cushion to the seat by placing the
cushion fully in the seat and lining up the fabric fasteners.
There is one fastener strip in the seat and the second
wraps around the back edge.
Step 2
Attach the back of the chair to the seat.
• First, locate the 2 cords that are attached to the left side
of chair seat (power cord and output jack) and make
sure they exit from the rear of the seat as shown in
Figure 1
• Next you will need to place the chair back into the seat.
Pick up the chair back with the zipper side facing the
front of the chair and lower the back into the seat so that
the knobs on either side of the back (Fig. 2) lock into the
latches in the chair seat (Fig. 1). The latches are marked
with bright green paint.
• The back will click into place and will sit evenly in the
seat. Once the back is sitting evenly in the chair seat,
confirm that the back and seat are attached correctly
by sitting in the chair and pulling the recline lever on
the right side of the chair (Fig. 3). The chair should
recline easily.
NOTE: If the back does not appear even or the chair does
not recline easily, then you may have engaged the latches
on only one side. To correct this you will need to release
the back as noted below and begin Step 2 again.
• Lumbar/Headrest pillow
*
Removable softening pad
currently in the backrest.
Step 3
Connect the power source.
• First, securely connect the output jack that is located on
the left rear of the chair seat to the input jack (Fig. 1) in
the lower left rear of the chair back (Fig. 4). Be sure that
the output jack is inserted with the word “Up” facing
upwards. When inserted correctly, the third or middle
horizontal line on the connector will meet the edge of the
input jack (Fig. 4).
• Plug the power cord into a grounded 120-volt outlet. This
product is equipped with a grounded plug and should
only be used with the appropriate outlet. Once all pieces
of the massage chair are in place and the main power
line is plugged in, you may turn the power switch on (Fig. 5).
• The eLounger contains a pass-through electrical outlet with
a maximum wattage of 300W as a convenience feature
(Fig. 5). NOTE: This outlet is an added convenience for
use with items such as the coordinating massaging
ottoman, a laptop, lamp or similar device. It will not
power the chair.
Removing the Back from the Seat
To remove the chair back from the seat:
• First, turn off the main power switch and unplug the unit.
Then remove the output jack from the chair back.
• Locate the levers along both sides of the rear of the chair
seat (Fig. 6).
• Push both at once and lean the chair back forward to
release it from the seat. Tip: Use your body or shoulder
to lean against the back as you depress the levers.
• To reconnect the back to the seat, repeat Step 2.
Enjoying Your Chair and General
Use
Choosing a Location
It is important to choose a location that will allow you to
best enjoy the chair’s benefits. The following is required for
the massage chair:
• The chair back should be approximately 1 foot from the
nearest object to recline fully.
• An electrical outlet that is a maximum of 8 feet from
the chair.
Power
Switch
Insert to
this line
Figure 4
Outlet
Fuse
Figure 5
Figure 6
67
In addition, we would suggest you consider the following
for your massage chair location:
• Choose a low traffic area so you can create a peaceful
environment when getting your massage.
• Choose a location in your home that makes you feel the
most comfortable and relaxed, but is also convenient.
• Adjustable lighting near the chair allows you to create
Figure 7
the right setting for your mood.
Moving Your Chair
Once you have selected the location for your chair, you
can easily move it with the convenient wheels located
on the rear of the chair (Fig. 7).
To move your chair, stand behind the chair and tilt it backwards until the wheels are engaged. Then simply push your
chair to the location you want. When you are lowering the
front of the chair in the spot you want it, be careful not to drop
it too hard or fast, as it may cause damage to your floors.
Figure 8
Turning On Your Chair
The eLounger massage chair has a master power switch
that must be in the “on” position in order to work. Once you
have plugged the chair power cord into the electrical outlet,
turn on the master power switch located on the back of the
chair (Fig. 8). Within the control panel, the green “e” in
eLounger and the red LED below it will illuminate to confirm
that the chair has power.
Reclining Your Chair
Figure 9
You can adjust the backrest angle to recline up to approximately 160 degrees. Reclining the backrest increases the
intensity of the massage, and also repositions the body so
that the massage range along your back and neck is
changed. Typically, the further you recline, the further the
massage will reach in the shoulder and neck area.
Recline
To recline the backrest using the manual control, lift the lever
on the right side of the chair seat (Fig. 3) and lean back.
When you are in the desired position, release the lever.
When you are ready to raise the backrest, pull the lever up
again and lean forward. The hydraulic gas system will raise
the backrest for you.
NOTE: In order to avoid strain and potential injury to your
back, never attempt to get in or out of the massage chair
with the backrest reclined.
Adjusting the Cushions
There are two adjustable cushions that are included with
your chair: the backrest softening pad and the lumbar/
headrest pillow.
THE BACKREST SOFTENING PAD
Your massage chair comes with a backrest softening pad.
It is recommended that you have this softening pad installed
for the most comfort while just sitting in the chair. In addition,
it is recommended that you use the softening pad while
getting a massage until your body is “used to” the intensity
of the massage. Once you are comfortable with it, you may
want to increase the intensity of the massage by removing
the softening pad. This will allow you to experience a deeper,
massage.
To install the softening pad:
• Lift the flap at the top of the chair to expose the ends of
the zippers (Fig 9) and unzip each side.
• Locate the inside pocket that holds the softening pad
(Fig.10). Simply insert or remove the softening pad (Fig. 11)
from this pocket.
• Close the zippers and the top flap.
THE LUMBAR/HEADREST PAD
The lumbar/headrest pillow (see page 16) is provided for
customized comfort. You may adjust its location to fit your
needs. For example, you can support your head and neck
or your lumbar area.
ADDITIONAL CUSHIONS:
You may add additional cushioning to the chair with your
own pillows. Keep in mind that the more cushioning you
add, the less you will be able to feel the massage.
Cup Holder
As an added convenience feature, the eLounger includes a
cup holder in the right armrest that will hold many types of
containers. To help maintain cleanliness, there is a removable
insert. A soft, damp cloth is recommended for cleaning.
Please see page 17 for additional information on care and
use for the eLounger.
Figure 10
Figure 11
8
9
Control Panel Overview
Programmed Massage Sessions
The eLounger includes 3 programmed
massage sessions - Full, Upper and Lower
Back - that are approximately 15 minutes
each as well as a short Demo program.
Push a program button and sit back and
enjoy. Once the program is finished, the
massage system will automatically shut
off. You can activate the massage system
again by pushing any button.
Manual Controls
Instead of using a program, you can
select a specific massage function using
these buttons. Once you have selected a
function, it will stay in that mode until you
push another function or turn the massage
system off.
Master Control/Indicators
This section of the control panel consists
of the master controls/indicators. It includes
the Stop function, which will stop the massage
action of both programmed and manual
functions, the Power Indicator and the
Ready Light.
NOTE: The massage system will stop
automatically after 20 minutes for
safety purposes.
13
5
6
11
Demo - To activate a brief pre-programmed course of the
1
3
2
4
7
8
9
12
10
14
1
massage functions.
Full Back - To activate a preset massage program for the
2
entire back.
Upper Back - To activate a preset massage program for
3
the upper section of the back.
Lower Back - To activate a preset massage program for
4
the lower section of the back.
5
Rolling - To activate the rolling function.
Kneading - To activate the kneading function.
6
Tapping - To activate the tapping function.
7
Kneading+Tapping - To activate the kneading+tapping
8
function.
Partial - To focus the massage in a partial range (approx. 4”)
9
for rolling, kneading, tapping & kneading+tapping.
Spot - To focus the massage in one spot for kneading,
10
tapping & kneading+tapping.
Adjust Up - To adjust the massage roller during partial &
11
spot functions.
Adjust Down - To adjust the massage roller during partial
12
& spot functions.
Tapping Intensity - To adjust the intensity of the massage
13
during tapping & kneading+tapping.
Width - To adjust the width of the massage during rolling
14
and tapping.
Stop - To stop the massage action
15
Power Indicators - The green “e” in eLounger will illuminate
16
when the recliner is powered on
Ready Light - The red LED will illuminate to indicate that
17
the recliner is powered and ready to use
15
16
17
1011
Loading...
+ 14 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.