Homecare 37602, 37601 Assembly Instructions Manual

Assembly Instructions for Homecare Crib Bed models 37601, 37602

Parts: Hardware:

2 End Frames 12 ¼"-20 x 2" Bolts
1 Side Rail with Handle 16 Washers
1 Non-moving Side Rail 12 ¼"-20 Nuts
1 Mattress Pan 4 ¼"-20 x 2¾" Bolts
1 Bottom Frame 3 ¼"-20 x 1 ½” Bolts (attached)
2 Non Locking Casters (attached)
2 Locking Casters (attached) Tools needed: 2 7/16" Wrenches

1. Place Mattress Deck on its side on a clean, flat surface.

2. Attach one End Frame to the Mattress Deck with 2 of the ¼"-20 x 2" bolts, washers and nuts.
Do not tighten completely. Repeat to attach second End Frame.

3. Lift Mattress Deck and End Frame to insert the remaining 4 bolts and washers. Attach nuts.
Do not tighten completely.

4. Attach Bottom Frame to End Frame with 2 of the ¼"-20 x 2" bolts, washers and nuts.

5. Stand the Bed in the upright position

6. Insert the remaining ¼"-20 x 2" bolts, washers and nuts to secure the Bottom Frame.

7. Position the Non-Moving Side Rail on the side of the Bed labeled “Non-Moving Side Rail.”
Attach with 1/4"-20 x 2¾" bolts. (Remove these labels after assembly.)

8. Tighten all bolts starting with the upper right, then lower left and continuing diagonally. Check all
screw caps for metal shavings which may be created while tightening. Check that Mattress
Deck and Bottom Frame are square and tightened.

9. Remove the nuts from the 3 bolts at the center of the side of the Mattress Deck. Push the bolts
in until they are flush with the Mattress Deck but do not remove bolts. Discard nuts.

10. Insert moving Side Rail into track. Hold or prop in fully raised position.

11. Locate lock housing at the bottom of the Side Rail. Push the 3 bolts back through the Mattress
Deck and thread into lock housing. Tighten bolts.

12. Raise and lower Side Rail several times to check operation.

13. Unwrap Mattress and place in Bed.

14. For Bed accessory installation and model # 37602 Crib Top installation, see page 9.

Assembly Instructions for Homecare Crib Bed models 37601-TDS, 37602-TDS

Parts: Hardware:

2 End Frames 12 ¼"-20 x 2" Bolts
2 Side Rails with Handles 12 ¼"-20 Nuts
1 Mattress Pan 12 Washers
1 Bottom Frame 6 ¼"-20 x 1 ½” Bolts (attached)
2 Non Locking Casters (attached)
2 Locking Casters (attached) Tools needed: 2 7/16" Wrenches

1. Place Mattress Deck on its side on a clean, flat surface.

2. Attach one End Frame to the Mattress Deck with 2 of the ¼"-20 x 2" bolts, washers and nuts.
Do not tighten completely. Repeat to attach second End Frame.

3. Lift Mattress Deck and End Frame to insert the remaining 4 bolts and washers. Attach nuts.
Do not tighten completely.

4. Attach Bottom Frame to End Frame with 2 of the ¼"-20 x 2" bolts, washers and nuts.

5. Stand the Bed in the upright position

6. Insert the remaining ¼"-20 x 2" bolts, washers and nuts to secure the Bottom Frame.

7. Tighten all screws starting with the upper right, then lower left and continuing diagonally. Check
all screw caps for metal shavings which may be created while tightening. Check that Mattress
Deck and Bottom Frame are square and tightened.

8. Remove the nuts from the 3 bolts at the center of the side of the Mattress Deck. Push the bolts
in until they are flush with the Mattress Deck but do not remove bolts. Discard nuts.

9. Insert one moving Side Rail into track. Hold or prop in fully raised position.

10. Locate lock housing at the bottom of the Side Rail. Push the 3 bolts back through the Mattress
Deck and thread into lock housing. Tighten bolts.

11. Repeat to attach second Side Rail.

12. Raise and lower Side Rails several times to check operation.

13. Unwrap Mattress and place in Bed.

14. For Bed accessory installation and model # 37602 Crib Top installation, see page 9.

Assembly Instructions for Homecare Crib Bed models 37603, 37604

Parts: Hardware:

2 End Frames 12 ¼"-20 x 2" Bolts
1 Side Rail with Handle 16 Washers
1 Non-moving Side Rail 12 ¼"-20 Nuts
1 Mattress Pan 4 ¼"-20 x 2¾" Bolts
1 Bottom Frame 3 ¼"-20 x 1 ½” Bolts (attached)
2 Non Locking Casters (attached)
2 Locking Casters (attached) Tools needed: 2 7/16" Wrenches

NOTE: Determine the correct position of the bed in the room before you begin to assemble
the bed. Choose the location for the head of the bed and the side where the non-moving side
rail will be located.

1. Place Mattress Deck on its side on a clean, flat surface.

2. Attach one End Frame to the Mattress Deck with 2 of the ¼"-20 x 2" bolts, washers and nuts.
Do not tighten completely. Repeat to attach second End Frame.

3. Lift Mattress Deck and End Frame to insert the remaining 4 bolts and washers. Attach nuts.
Do not tighten completely.

4. Attach Bottom Frame to End Frame with 2 of the ¼"-20 x 2" bolts, washers and nuts.

5. Stand the Bed in the upright position

6. Insert the remaining ¼"-20 x 2" bolts, washers and nuts to secure the Bottom Frame.

7. Position the Non-Moving Side Rail on the side of the Bed labeled “Non-Moving Side Rail.”
Attach with 1/4"-20 x 2¾" bolts. (Remove these labels after assembly.)

8. Tighten all bolts starting with the upper right, then lower left and continuing diagonally. Check all
screw caps for metal shavings which may be created while tightening. Check that Mattress
Deck and Bottom Frame are square and tightened.

9. Remove the nuts from the 3 bolts at the center of the side of the Mattress Deck. Push the bolts
in until they are flush with the Mattress Deck but do not remove bolts. Discard nuts.

10. Insert moving Side Rail into track. Hold or prop in fully raised position.

11. Locate lock housing at the bottom of the Side Rail. Push the 3 bolts back through the Mattress
Deck and thread into lock housing. Tighten bolts.

12. Raise and lower Side Rail several times to check operation. Turn the crank at the foot of the
bed to raise and lower the head of the bed to check operation.

13. Unwrap Mattress and place in Bed. For Bed accessory installation and model # 37604 Crib Top
installation, see page 9.