Home Automation 40A00-1, 37A00-1 User Manual

HAI UPB™ 15A Relay Switch and Auxiliary Switch

Installation and Operating Instructions

For the following Models:

40A00-1 HAI 15A Relay Switch (referred to as HAI UPB
37A00-1 HAI Auxiliary Switch

READ THESE INSTRUCTIONS BEFORE INSTALLING DEVICE

This HAI UPB™ Wall Switch and Auxiliary Switch is intended for installation in accordance with the National Electrical Code and
local codes and regulations. It is recommended that a qualified electrician perform this installation. Retain these instructions for
reference.

This product is for indoor use only. Connect only copper or copper clad wire to this device.

Important Notes Prior To Installation

1. All HAI UPB™ Wall Switches require a neutral (white) connection wire.

2. Be sure that all power to the load has been disconnected by turning off the circuit breaker. Installing an HAI UPB™ Wall Switch

or Auxiliary Switch with power on may expose you to dangerous voltage and may damage the device.

HAI UPB™ Wall Switch Overview

The HAI UPB™ Wall Switch (Figure 1) allows for local control of loads by using the Decora-style rocker switch. It also incorporates
the UPB™ two-way powerline communication technology that gives it the ability to be remotely controlled by UPB™ compatible
controllers. The HAI UPB™ Wall Switch is also capable of transmitting UPB™ messages when the rocker switch is turned on or
turned off.

The HAI 15A Relay Switch is used to control loads such as receptacles, motor-operated appliances (i.e. fans), and fluorescent lighting
fixtures.

LED
INDICATOR

TOP
(ON)

BOTTOM
(OFF)

Figure 1 - HAI UPB™ Wall Switch

™ Wall Switch, in this document), and

BLACK

WHITE

RED

YELLOW

GREEN

GROUND

LINE

NEUTRAL

LOAD

CONTROL

40I00-1, Rev B

HAI Auxiliary Switch Overview

The 37A00-1 HAI Auxiliary Switch (Figure 2) is an optional companion device used with the HAI UPB™ Wall Switch for multi-way
circuits. The HAI Auxiliary Switch has a Decora-style rocker switch that controls the load in the exact same manner as the Decora­style rocker switch on the HAI UPB™ Wall Switch.

LED
INDICATOR

TOP
(ON)

BOTTOM
(OFF)

BLACK

GRAY

BLUE

YELLOW

LINE

*NEUTRAL

(FOR RED INDICATOR)

*NEUTRAL

(FOR BLUE INDICATOR)

CONTROL

Figure 2 – HAI Auxiliary Switch

Changing Switch Color

The color of the HAI UPB™ Wall Switch and Auxiliary Switch may be changed to
complement the interior décor. The HAI UPB™ Wall Switch and Auxiliary Switch
is supplied with a white switch plate. Additional colors are available; contact your
HAI distributor for more information. When changing the switch plate, make sure
that the switch is disconnected from all power, and proceed as follows:

1. The switch plate attaches to the HAI UPB™ Wall Switch and Auxiliary Switch

with two latches on the right and two on the left. Using a small-bladed
screwdriver, gently depress the upper and lower latch on one side while lifting
up on the plate. Once the latches are released on one side, remove the switch
plate from the other side.

2. Align the latches of the new switch plate to the openings on the mounting plate

and gently snap into place.

Figure 3 – Changing Switch Color

INSTALLATION INSTRUCTIONS

The HAI UPB™ Wall Switch is wired directly to the load and can be controlled by adding one or more optional HAI Auxiliary
Switches producing multi-way circuits. Multi-way circuits make it possible for a group of switches to control the same load. This
section will illustrate how to make the connections.

Notes:

1. Refer to Figures 1 and Figure 2 to determine the wire colors for each connection.

2. All HAI UPB™ Wall Switches require a neutral (white) connection.

3. The Line (black) wire must be accessible for the installation of all HAI Auxiliary Switches. This wire may be connected to either

phase of the 120/240V supply. The blue and/or gray wire on the HAI Auxiliary Switch can be connected to either earth ground or
neutral. The blue and/or gray wire is only used to light the LED on the switch. This LED only indicates that power is applied and
serves as a night-light. Connect the blue wire only to light the LED blue. Connect the gray wire only to light the LED red.
Connect both the blue wire and the gray wire to light the LED magenta.