HAI Omni-Bus 6-Channel Keyfob Remote
Model 125A00-1
SPECIFICATIONS
DELETING A REMOTE CONTROL
Check for a
(See receiving device user
does not
device user manual for more
FCC ID: HHC-115A00-1
art 15 of the FCC Rules. Operation is
(1) This device may not cause
harmful interference, and (2) this device must accept any interference
hanges or modifications not expressly approved by the
r compliance could void the user's authority to
User’s Guide
o 6 Channels
o For use with HAI Omni-Bus Output devices
o Requires an HAI Omni-Bus RF Transceiver or HAI Omni-Bus
Translator Interface on the Omni-Bus network
o Frequency: 433.92MHz
o Range: Up to 30m (98 feet) indoors, up to 100m (328 feet)
outdoors
REMOTE CONTROL FUNCTIONS
To switch a device ON or OFF
Press and release the button on the
Remote Control. The remote control
will toggle between the ON and OFF
commands each time the button is
To DIM a light (when used with an Omni-Bus Dimmer unit)
Enter DIM/BRIGHT mode on the Remote control by pressing
buttons 1 and 2 simultaneously.
The Remote Control will exit the DIM/BRIGHT mode automatically
if no buttons are pressed for 7 seconds.
A forced exit can be achieved by pressing buttons 1 and 2
simultaneously again.
pressed.
Press and hold the appropriate
button on the Remote Control to dim
or brighten the light.
OMNIBUS PROGRAMMING
See the HAI OMNIBUS Software User Guide for more information
on how to program the remote control into an Omni-Bus output
devices using the OMNIBUS Installation Software.
MANUAL PROGRAMMING
1. Place the receiving device into the programming mode. This is
normally done by pressing and holding the button on the
receiving device until its LED starts flashing continuously.
(See receiving device user guide for more information).
2.
3. Exit the programming mode on the receiving device.
Press and hold the DESIRED
channel button on the Remote
Control until the remote sounds 3
beeps (approx.10 seconds). Check
for a confirmation signal from the
receiving device. (See receiving
device user manual for more
information).
REMOTE CONTROL BATTERY REPLACEMENT
If the remote control does not respond to any key presses or the
LED fails to come on when a key is held in, the battery may need
replacement.
The remote control uses one type 23A 12V battery.
© 2012 Home Automation, Inc. www.homeauto.com Document: 125I00-1, Rev2.0 September 2012
A Remote Control channel programmed into an Omni-Bus receiving
device may be deleted from that device via the OMNIBUS Installation
Software or by following the procedure below:
1. Place the receiving device into the programming mode. This is
normally done by pressing and holding the button on the
receiving device until the receiving device LED starts flashing
continuously (see receiving device user guide).
2.
3. Exit the programming mode on the receiving device.
DELETE ALL
All remote control channels programmed into ANY Omni-Bus
RECEIVING device can be deleted entirely by using any Omni-Bus
Remote Control. The remote control used for this
necessarily need to be one that was previously programmed into the
device. This allows a lost or stolen remote control to be deleted
before reprogramming the new remote control.
1. Place the receiving device into the programming mode. This is
normally done by pressing and holding the button on the
receiving device until the receiving device LED starts flashing
continuously (see receiving device user guide).
2.
3. Exit the programming mode on the receiving device.
KEYPAD LOCK FUNCTION
The keypad lock function can be used to prevent accidental remote
control activation.
Enabling the Keypad Lock Function
Before the keypad lock function can be used, it has to be enabled as
follows: Press and hold button 3 and 4 simultaneously until the
remote sounds a burst of beeps (after approximately 5 seconds).
Disabling the Keypad Lock Function
Press and hold button 3 and 4 simultaneously until the remote
sounds a short beep (after approximately 5 seconds).
Locking/Unlocking the Keypad
Lock or Unlock the Keypad on the Remote Control by pressing
buttons 3 and 4 simultaneously. The Remote Control will sound a
long beep when the Keypad is locked and any key is pressed on the
remote control.
This device complies with P
subject to the following two conditions:
received, including interference that may cause undesired operation.
Caution: C
party responsible fo
operate the equipment.
Press and hold the appropriate button
on the remote control until the remote
sounds 3 beeps followed by another
set of 4 beeps.
confirmation signal from the receiving
device.
manual for more information).
Press and hold any button on the
remote control until the remote sounds
3 beeps, then 4 beeps and then 5
beeps (approximately 17 seconds).
Check for a confirmation signal from
the receiving device. (See receiving
information).
IC: 1516A-115A001
© 2012 Home Automation, Inc.
www.homeauto.com
Document: 125I00-2, Rev2.0 September 2012
HAI Omni-Bus 16-Channel Keyfob Remote
Model 125A00-2
SPECIFICATIONS
OMNIBUS PROGRAMMING
allows a lost or stolen remote control to be deleted before
Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) this device must accept any interference
ifications not expressly approved by the
party responsible for compliance could void the user's authority to
User’s Guide
o 16 Channels
o For use with HAI Omni-Bus Output devices.
o Requires an HAI Omni-Bus RF Transceiver or HAI Omni-Bus
Translator Interface on the Omni-Bus network
o Frequency: 433.92MHz
o Range: Up to 30m (98 feet) indoors, up to 100m (328 feet)
outdoors
CHANNEL SELECTION
The remote control has 16 channels.
4 Layers x 4 Channels on each Layer = 16
To select a layer:
After a channel was selected, that selection will remain active until
another channel is selected i.e. all subsequent function operations will
be done with the selected channel.
Select a layer number from 1 to 4 by
pressing and holding the appropriate
channel key (1, 2, 3 or 4) until the
remote sounds 2 beeps.
Now press and release the key for the
desired channel on the selected layer. If
another channel on the same layer
needs to be selected, the layer selection
does not have to be repeated.
REMOTE CONTROL FUNCTIONS
To switch a device ON or OFF:
1. Select the appropriate channel on the remote control (see
CHANNEL SELECTION).
2.
3.
To DIM a light (when used with an Omni-Bus Light Dimmer)
1. Enter the DIMMING MODE by pressing and releasing both the
UP and DOWN buttons simultaneously. The remote control will
sound 2 beeps.
2. Select the appropriate channel on the remote control (see
CHANNEL SELECTION).
3.
4.
The Remote Control will exit the DIM/BRIGHT mode automatically if no
buttons are pressed for 7 seconds. A forced exit can be achieved by
pressing the UP and DOWN buttons simultaneously again.
Press and release the UP button to
switch ON.
Press and release the DOWN button to
switch OFF.
Press and hold the DOWN button to
DECREASE the light level.
Press and hold the UP button to
INCREASE the light level.
See the HAI OMNIBUS Software User Guide for more information on
how to program the remote control into Omni-Bus output devices using
the OMNIBUS Installation Software.
MANUAL PROGRAMMING
1. Select the appropriate channel on the remote control (see
CHANNEL SELECTION).
2. Place the receiving device into the programming mode. This is
normally done by pressing and holding the button on the
receiving device until its LED starts flashing continuously. (See
receiving device user guide for more information).
3.
4. Exit the programming mode on the receiving device.
Press and hold the UP button on the
remote control until the remote sounds 3
beeps. Check for a confirmation signal
from the receiving device. (See
receiving device user guide for more
information).
DELETING A REMOTE CONTROL
A Remote Control channel programmed into an Omni-Bus receiving
device may be deleted from that device via the OMNIBUS Installation
Software or by following the procedure below:
1. Select the channel on the remote control to be deleted (see
CHANNEL SELECTION).
2. Place the receiving device into the programming mode.
3.
4. Exit the programming mode on the receiving device.
Press and hold the DOWN button on the
remote control until the remote sounds 3
beeps. Check for a confirmation signal
from the receiving device. (See
receiving device user guide for more
information).
DELETE ALL
All remote control channels programmed into ANY Omni-Bus
RECEIVING device can be deleted entirely by using any Omni-Bus
Remote Control. The remote control used for this does not necessarily
need to be one that was previously programmed into the device. This
reprogramming the new remote control.
Follow the procedure for deleting a single channel but keep holding the
DOWN button until the remote sounds another 4 beeps.
FCC ID: HHC-115A00-1
IC: 1516A-115A001
This device complies with Part 15 of the FCC
received, including interference that may cause undesired operation.
Caution: Changes or mod
operate the equipment.
© 2012 Home Automation, Inc.
www.homeauto.com
Document: 125I00-2, Rev2.0 September 2012
KEYPAD LOCK FUNCTION
The keypad lock function can be used to prevent accidental remote
control activation.
Enabling the Keypad Lock Function
Before the keypad lock function can be used, it has to be enabled as
follows: Press and hold button 3 and 4 simultaneously until the remote
sounds a burst of beeps (after approximately 5 seconds).
Disabling the Keypad Lock Function
Press and hold button 3 and 4 simultaneously until the remote sounds
a short beep (after approximately 5 seconds).
Locking/Unlocking the Keypad
Lock or Unlock the Keypad on the Remote Control by pressing buttons
3 and 4 simultaneously. The Remote Control will sound a long beep
when the Keypad is locked and any key is pressed on the remote
control.
REMOTE CONTROL BATTERY REPLACEMENT
If the remote control does not respond to any key presses or the LED
fails to come on when a key is held in, the battery may need
replacement. The remote control uses one type 23A 12V battery.
Loading...