Wireless Dimmable
Controller
User Guide
H
C61 0-Z
L
HLC610-Z is a kind of ZigBee 0-10V controllers that works with 010V LED dimmable driver.
Environment and Electrical parameters
1
Parameters
Ac In
Ac Out
Dim Out
RJ12
Max Current of 0-10V
Max Current of Relay
Wireless Frequency
Operation Temperature
Wiring Diagram
2
Below is HLC610-Z system connection diagram, where the motion sensor is
optional:
100-277Vac to constant current power supply
Motion Sensor & Daylight sensor module
HLC610-Z
100-277Vac
0-10V
20mA
10A
2.4GHz
-20°C to 70°C
1
ACL In
ACN In
ACN Out
ACL Out
3
Installation
HLC610-Z Controller
0-10V/PWM Driver
0-10V/PWM+
GND
LED+
LED-
Highbay
3.1. Install App into smart phone or tablet device .
3.2. iOS: search and install “iLightsIn” from App Store or scan the iOS QR
code.
3.3. Android: search and install “iLightsIn” from Google Play or scan the
android QR code.
AndroidiOS
2
iLightsIn App User Guide
4
4.1. WiFi settings
Power on the gateway. Please select the WLAN iLightsInxxxxxx on mobile
settings menu. The xxxxxx is the mac address at the back of gateway. Connect
the WiFi AP, and open iLightsIn App (Picture1).
4.2. Enter application
Help menu will pop up first time you open the App. When finishing reading the
instruction, you are directed to the Settings menu. User can start to add
device or connect the gateway to a router from Settings.
4.3. Device
Add device: Settings - New device (Picture2) - scan QR code (Picture 3).
P.S.: Each device has one unique QR code.
Pic ture 1 Pic ture 2
Pic ture 3
3
4.4. Area
Users can create different areas and put relevant devices in. Click one area,
enter the sub menu and all different devices are listed there.
User can control each device in this area (Picture4).
- Move the slider to change color or brightness.
- Click to enter Timer or Delay menu. Under this menu, user can set
timers or delays and different status while timeout (Picture5).
4.5. Binding settings
User can bind touch switches or remote controls to lights in this menu (Picture6).
Pic ture 4 P ictu re5 Pic ture 6
4
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception,which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, This equipment
should be installed and operated with minimum distance between 20cm the
radiator your body: Use only the supplied antenna.
FCC ID:2AJ7E-HLC610-Z
5
Loading...