Single Track Bypass Barn Door Hardware
Installation Manual
SAFETY PRECAUTIONS
WARNING!
Power tools can cause serious damage if not professionally used. Safety gear
must be worn before installation to prevent unexpected injuries.
Pick an area free of hazardous condition before you start on the project .
Please use t ools and power tools responsibly any loss o f control and
accident deaths may occur due to abuse of tools.
Please make sure all hardware is secured on to the door is sufficiently tight.
Doors with loose hardware may result in unexpected serious injuries. To
avoid any problems, be sure hardware is secure before door is put on the track.
All hardware provided is for safety reasons. Anti-Jump systems are to prevent
doors from falling off the track while in use. Please follow each instruction
carefully. Track
secure from serious problems. All safety hardware and instructions included
in this project must be used and followed specifically to prevent any unforeseen
serious problems.
must be installed on studs in order to keep the track and doors
!CAUTION!
Big objects required in this project are needed to be carefully and responsibily
moved. Be sure to wear safety gloves and shoes to prevent any serious injury.
Be extremely careful to not put any parts of your body against a moving part
of the hardware. This may cause bruising, punctures, and other results of
injuries when for example when fingers are caught in the closing area
of the doors.
Precautions should be taken when opening or closing the door(s). Handles
should be used when attempting to slide the door(s). Always keep you and
children aware and safe from any unexpected situations.
Any extreme uncontrolled pressure opening or closing the door(s) can damage
the hardware gradually. Use handle(s) to open and close the door(s) with care
at all times.
HARDWARE INCLUDED
Different track length comes with different hardware quantity.
Please be sure to check the hardware you should have before installation.
contains:
Hex Bolt (4), Acorn Nut (4), Washer (8) Anti-Jump Pad (2), Floor Guide (1) Door Stopper (2), Hex Wrench (1)
Bent
4FT
4.5FT
5FT
5.5FT
6FT
6.6FT
7FT
7.5FT
8.FT
9FT
10FT
11FT
12FT
13FT
14FT
15FT
16FT
18FT
20FT
contains:
L Shape
Spacer, Lag Bolt, and Washer Set
HARDWARE CHECKLIST
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
10
10
10
12
12
15
15
3
3
4
4
5
5
5
6
6
6
8
8
Adjustable
Junction PlateFlat TrackBent Hanger/ Roller BoxHanger/ Roller BoxTrack Measurement Spacer, Lag Bolt and, Washer Set
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
www.homacer.com
INSTRUCTIONS
Draw a horizontal line using the following formula
(1/2” + Door Height + 1 1/2”). This line will be
used to line up horizontally to the center of the track.
If your track comes in 2pcs
or more, install the junction
plate on to each two tracks
like the diagram shown here.
Door
Height
REMINDER: Make sure your floor is level. If
not, please measure the distance from the
highest point of your floor.
This procedure should be done so that when the
doors go on the track it will slide smoothly above
that highest point of the floor.
Find all the studs and then lay your track onto
the wall, Make sure the line you drew previously
lines up horizontally to the center of the track
and each hole is on the studs location. Then
mark the center of the holes position.
REMINDER: Depth of track to wall is 1 3/8”.
If you have a door trim be sure to use a header that
has the same thickness of your trim before installation
of the track or a second option would be a 3/4”
spacer extenders which we can offer when
requested, so the door can clear off the door trim
when sliding. Also if your track cannot line up to the
studs be sure to use a header board for safety purposes.
1. Drill the previously marked holes and install
the lag bolt and spacer onto the first hole as shown
in the picture.
2. Install the door stoppers on an approximate
position where you want the doors to stop.
3. Repeat the same process for the remaining
holes.
CAUTION:Do not over tighten when installing
the track on any drywall surfaces or you may
be at risk of damaging your drywall.
Notice: The reason of installing the door stoppers
before mounting the second hole is to avoid taking
off the already installed bolts and spacers if you
decide to install the stoppers between the two
holes. The door stoppers position is adjustable
between the two holes using the hex wrench.
www.homacer.com
Open a slot that is 1/4” wide and 13/16” deep at the
bottom of the door with a router. This groove will be used
with the floor guide.
Straight Design HangerClassic Design Hanger
Drill the holes for the hanger according to the dimension
given in the picture. This distance from the top of the door to
the center of the upper hole is 1 5/8”. The distance from the
left (right) edge of the door to the left (right) edge of the
hanger is up to your choice. It should be at least be a
minimum of 1” away from the edge to prevent any
damage to your doors
Here is the formula to calculate the overlap space:
5
Overlap Diagram
The overlap = 2* Distance from the left (right) edge of the
door to the left (right) edge of the hanger + 4 1/4”
For example, if you install each hanger 1” from the edge of
the door, the overlap is 2* 1” + 4 1/4” = 6 1/4”
Please follow the diagram above on how the hex bolt,
washers and nut should be installed on the door and
hangers. Do not install them any other way since it
may interferee with the function of the sliding system.
1
”
4 1”1”
4
INSIDE DOOR
www.homacer.com
Install the anti-jump pads on top of the door as
shown in the picture. There is no strict requirement
on its position.
-
To mount your doors onto the track, you will
have to lift your door at a slight angle and rest
both wheel grooves onto the top of the track
carefully.
Usually floor guides are installed in the middle of
the opening for single track bypass but we
recommend to install the regular floor guide in
your own location preference depending on how
you want your inside door to slide. After the
door is hung on to the track you will be able to
locate where you want the floor guide to be
installed according to your decision of sliding.
-
Screw
Washer
L-Shape Anti-Jump
Nut
Assemble accordingly like the diagram shown in this
box. This an anti-jump system that helps to secure
the hanger when placed on to the track.
-
5
Straight Design HangerClassic Design Hanger
Repeat the same step for the bent
hanger design.
Just like step 5.
Please follow the diagram above on how the hex bolt,
washers and nut should be installed on the door and
hangers. Do not install them any other way since it
0
1
may interfere with the function of the sliding system.
INSTALLATION OF THE ADJUSTABLE FLOOR GUIDE FOR BENT HANGERS
Put the hardware together.
Locate the area of the door to install the bypass floor guide.
Install the bypass floor guide on to the area marked.
on the in
of the first and second
hole.
Adust the bypass floor guide.
dicated area
Locate the area where the two doors
Inside Door
overlap when its fully closed. Have the
floor guide to be installed on the inside
door.(Inside door is tinted on the diagram.)
Mark the dotted guides on
1
t
he location of the inside door.
Now fasten the screws
tightly so the adjusment
does not move out of
place.
Have the outside door set on the track.
You can now put the outside door on the
track and fit t he tip in to the doors groove
while following step 12.
Repeat the same step for the doors with bent hanger
as Step 7. You can use this method
to slip the groove
of the door into the tip of the floor guide.
2
YOUR INSTALLATION IS COMPLETE!
6
www.homacer.com
SLIDING HARDWARE / BARN DOORS
High Quality Exquisite Design Outstanding Services
ABOUT US
At Homacer, our goal is to provide the finest sliding
barn door hardware products and services for our
valued customers. We keep polishing our products
to make their quality better, prices lower and
installation easier. We make it possible for you to
get everything you need from us when you think
about installing sliding barn doors.
CONTACT US
Office #: 1(770) 864-5437
Website: www.homacer.com
Email us: info@homacer.com
LOCATION
1885 Beaver Ridge Cir, Ste A
Loading...