Standard Single Door & Double Door Hardware
Installation Manual
SAFETY PRECAUTIONS
WARNING!
Power tools can cause serious damage if not professionally used. Safety gear
must be worn before installation to prevent unexpected injuries.
Pick an area free of hazardous condition before you start on the project .
Please use t ools and power tools responsibly any loss o f control and
accident deaths may occur due to abuse of tools.
Please make sure all hardware is secured on to the door is sufficiently tight.
Doors with loose hardware may result in unexpected serious injuries. To
avoid any problems, be sure hardware is secure before door is put on the track.
All hardware provided is for safety reasons. Anti-Jump systems are to prevent
doors from falling off the track while in use. Please follow each instruction
carefully. Track
secure from serious problems. All safety hardware and instructions included
in this project must be used and followed specifically to prevent any unforeseen
serious problems.
must be installed on studs in order to keep the track and doors
!CAUTION!
Big objects required in this project are needed to be carefully and responsibily
moved. Be sure to wear safety gloves and shoes to prevent any serious injury.
Be extremely careful to not put any parts of your body against a moving part
of the hardware. This may cause bruising, punctures, and other results of
injuries when for example when fingers are caught in the closing area
of the doors.
Precautions should be taken when opening or closing the door(s). Handles
should be used when attempting to slide the door(s). Always keep you and
children aware and safe from any unexpected situations.
Any extreme uncontrolled pressure opening or closing the door(s) can damage
the hardware gradually. Use handle(s) to open and close the door(s) with care
at all times.
HARDWARE INCLUDED
Different track length comes with different hardware quantity.
Please be sure to check the hardware you should have before installation.
Hanger/Roller Box
Steel Hanger/Roller (2)
contains:
Hex Bolt (4), Acorn Nut (4), Washer (8)
Anti-Jump Pad (2), Floor Guide (1)
Door Stopper (2), Hex Wrench (1)
Flat Track
4FT
4.5FT
5FT
5.5FT
6FT
6.6FT
7FT
7.5FT
8FT
9FT
10FT
11FT
12FT
13FT
14FT
15FT
16FT
18FT
20FT
Spacer, Lag Bolt, and Washer Set
Junction Plate
HARDWARE CHECKLIST
Hanger/Roller Box for Double Door KitHanger/Roller Box for Single Door Kit
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
1
1
1
1
1
1
1
1
2
2
2
2
2
2
2
2
2
2
10
10
10
12
12
15
15
Junction PlateFlat TrackTrack Measurement Spacer, Lag Bolt and, Washer Set
3
3
4
4
5
5
5
6
6
6
8
8
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
www.homacer.com
2
TYPE OF HANGERS
1 5/8’’ 1 5/8’’ 1 5/8’’
1 5/8’’
Classic Straight Arrow Black Wheel
1 5/8’’1 5/8’’
Star Gear Flame Mustache
1 5/8’’
Imperial Bucks Twig Royal
1 1/8’’
1 5/8’’
1 5/16’’
1 5/8’’ 1 5/8’’
1 5/8’’
3 1/2’’
1 5/8’’
2 1/2’’
Anchor Diamond
1 1/4’’
3 11/16’’
Horseshoe T-shape
Horns Shuriken
www.homacer.com
INSTRUCTIONS
Draw a horizontal line using the following formula
(1/2” + Door Height + 1 1/2”). This line will be
used to line up horizontally to the center of the track.
If your track comes in 2pcs
or more, install the junction
plate on to each two tracks
like the diagram shown here.
Door
Height
REMINDER: Make sure your floor is level. If
not, please measure the distance from the
highest point of your floor.
This procedure should be done so that when the
doors go on the track it will slide smoothly above
that highest point of the floor.
Find all the studs and then lay your track onto
the wall. Make sure the line you drew previously
lines up horizontally to the center of the track
and each hole is on the studs location. Then
mark the center of the holes position.
REMINDER: Depth of track to wall is 1 3/8”.
If you have a door trim be sure to use a header that
has the same thickness of your trim before installation
of the track or a second option would be a 3/4”
spacer extenders which we can offer when
requested so the door can clear off the door trim
when sliding. Also if your track cannot line up to the
studs be sure to use a header board for safety purposes.
1. Drill the previously marked holes and install
the lag bolt and spacer onto the first hole as shown
in the
2. Install the door stoppers on an approximate
position where you want the doors to stop.
3. Repeat the same process for the remaining
holes.
CAUTION:Do not over tighten when installing
the track on any drywall surfaces or you may
be at risk of damaging your drywall.
Notice: The reason of installing the door stoppers
before mounting the second hole is to avoid taking
off the already installed bolts and spacers if you
decide to install the stoppers between the two
holes. The door stoppers position is adjustable
between the two holes using the hex wrench.
picture.
homacer
4
Step-
Open a slot that is 1/4” wide and 13/16” deep
at the bottom of the door with a routher. This
groove will be used with the floor guide.
3 1/2''
Step
Drill the holes for the hanger according to the
dimension given in the picture.The distance
between the top edge of the door and the
center of the upper hole is 1 5/8”. The distance
between the side edge of the door and the
hanger is up to your choice. It should be at
least be a minimum of 1” away from the edge to
''
prevent any damage to
your doors. Next, install
the hex bolts and acorn nuts as shown in the
picture.
Notice: If you have other design hanger,
Please follow the diagram above on how the
hex bolt, washers and nut should be installed
on the the door and hangers. Do not install
-
them any other way since it may interfere with
the function of the sliding system.
please look up the dimension on Page 6.
Step
Install the anti-jump pads as shown in the
picture.
-
5
homacer
Step
To mount your doors onto the track, you
will have to lift your door at a slight angle
and rest both wheel grooves onto the top
of the track carefully.
7
-
Usually floor guides are installed corner of the
opening for standard single and double door
hardware but we recommend to install the regular
floor guide in your own location preference
depending on how you want your inside door to slide.
After the door is hung on to the track you will be
able to locate where you want the floor guide to
be installed according to your decision of sliding.
Step- 8
Notice: If you have two doors you can repeat from
step 4 to step 8 again for the second door installation.
YOUR INSTALLATION IS COMPLETE!
homacer
SLIDING HARDWARE / BARN DOORS
High Quality Exquisite Design Outstanding Services
ABOUT US
At Homacer, our goal is to provide the finest sliding
barn door hardware products and services for our
valued customers. We keep polishing our products
to make their quality better, prices lower and
installation easier. We make it possible for you to
get everything you need from us when you think
about installing sliding barn doors.
CONTACT US
Office #: 1(770) 864-5437
Website: www.homacer.com
Email us: info@homacer.com
LOCATION
1885 Beaver Ridge Cir, Ste A
Loading...