Publication
Please Contact
Technical Support At 203
-
736-8890 With Any Additional Questions
Page
TP, GRP, and T Motor Voltage Change
This procedure will provide you with step by step instructions
to convert the operating voltage of dual voltage 3 phase.
You Need:
5 mm Allen Wrench
Wire Cutters
Wire Strippers
Terminal Crimp Tool
Qty 6-Crimpable Wire Nuts 14 to 16 Gage
2. With pump in stable, upright position,
remove the four 5mm cap screws as
indicated.
1. Remove pump from service. Disconnect
power supply. Clean and decontaminate
pump prior to working on it. See the
pump Installation, Operation, and
Maintenance Manual for detailed
instructions.
88FN2045A
3. With the cap screws removed, lift the
stator housing off of the pump.
Please Be Prepared To Provide Pump Serial Number During Call
1 of 5
Publication
Please Contact
Technical Support At 203
-
736-8890 With Any Additional Questions
Page
4. Sometimes the housing will be difficult to
remove. Twist the housing ¼ turn (90
degrees), exposing the bottom of the
cable entry horn. Using a soft faced
hammer, gently tap the cable entry horn
to free the stator housing.
6. With motor disassembled, turn stator
housing upside down, and support it so it
is free standing. Stator windings and
cable leads must be visible and easy to
reach. Your unit should now look like
this. Gently remove all wires from around
the stator windings. Take care not to
damage the winding insulation. Do not
use sharp tools!!
5. With stator housing removed, locate the
upper bearing spacer and the bearing
support washer. The upper bearing
spacer may still be inside of the housing.
Clean Place those items aside until
reassembly.
88FN2045A
Please Be Prepared To Provide Pump Serial Number During Call
2 of 5
Publication
Please Contact
Technical Support At 203
-
736-8890 With Any Additional Questions
Page
7. Separate the wire bundles as indicated,
and record the wire numbers in each
bundle.
If pump is wired for 208/230V, it will have 4
wire bundles. If pump is wired for 460V, it
will have 6 wire bundles.
Bundle 1 ___ ___ ___
Bundle 2 ___ ___ ___
Bundle 3 ___ ___ ___
Bundle 4 ___ ___ ___
Bundle 5 ___ ___ ___
Bundle 6 ___ ___ ___
Note: If the power cable is 4 lead, the wires
are color coded. If the power cable is 7 lead,
each individual wire will have a number on
cable sheath. The power leads will not have
a separate wire number.
8. To convert from 230V to 460V operation,
you will need to separate the wire
bundles, one at a time, and reconnect as
indicated below.
9. To perform the reconnection, locate the
wire bundle with wires 1, 7, and the
power lead. Cut wire connector from the
bundle, freeing individual wires. Strip
wire sheathing back ¼ in preparation for
reconnection.
10. Select wire number 1 and the power lead.
Reconnect these 2 wires with the
crimpable wire nut (close end connector).
Leave wire number 7 loose for now.
88FN2045A
Please Be Prepared To Provide Pump Serial Number During Call
3 of 5
Publication
Please Contact
Technical Support At 203
-
736-8890 With Any Additional Questions
Page
11. Repeat procedure for wire bundle 2, 8,
and power. After separating wires
reconnect wire number 2 and power lead
with crimp wire nut. Leave wire number 8
loose for now.
12. Repeat procedure for wire bundle 3, 9,
and power. After separating wires
reconnect wire number 3 and power lead
with crimp wire nut. Leave wire number 9
loose for now.
13. Now, you will need to separate the wire
bundle with numbers 4, 5, 6, and pair
each wire with the loose wires numbers 7,
8, and 9 as indicated. Using the last
three wire connectors:
Join wire #4 to wire #7
Join wire #5 to wire #8
Join wire #6 to wire #9
Now you should have three new bundles
2 and power
3 and power
1 and power
along with 3 separate wires (#7,#8,#9), and
one bundle of 3 wires (#4,#5,#6).
14. At this point, you should have 6 separate
wire bundles, each with 2 wires. Wires
should be paired as follows: 4 to 7, 5 to 8,
6 to 9, #1 to power, #2 to power and #3
to power. See photo
Before proceeding, you should check the
resistance between all three cable leads
is the same. Resistance value is different
for the various size motors, so please
consult wiring handbook for specific
resistance values, if required.
88FN2045A
Please Be Prepared To Provide Pump Serial Number During Call
4 of 5
Publication
Please Contact
Technical Support At 203
-
736-8890 With Any Additional Questions
Page
15. Starting with bundles 4-7, 5-8, 6-9, gently
tuck these 3 wire bundles behind the
windings on one side of stator. Then tuck
the remaining 3 bundles behind the
windings on the other side. Take care that
all wires are tucked between stator
winding and housing. Also check that
white phase paper is in proper position,
and not extending below the stator
housing.
16. Place the spacer and washer on top of
upper bearing. Use a little bit of grease to
hold in position if necessary.
17. Verify that the large o ring is still in it’s
proper position on the pump housing.
Gently place motor housing back onto
pump, taking care not to disturb spacer
when reinstalling.
The pump is now ready for reassembly
88FN2045A
18. With motor housing back in position,
rotate motor housing until cable entry
horn is in line with pump discharge as
indicated in photo. Then align bolt holes
and replace capscrews. Tighten
capscrews to 12 ft/lbs.
19. Pump should now be ready for installation
and operation at 460V. Be sure to record
that voltage has been changed in pump
service manual.
Please Be Prepared To Provide Pump Serial Number During Call
5 of 5
Loading...