Holtkoetter C8110-R User Manual

ASSEMBLY INSTRUCTIONS FOR

205 Hardman Avenue South, South Saint Paul, MN 55075

Voice: [phone] • Fax: [phone]

e-mail: [e-mail]

www.holtkoetter.com

QUICK-CONNECT INSTRUCTIONS

1. Once the LICHTSTAR canopy has been
installed, the quick-connect feature
completes the fixture.

2. Be sure to discard the nut (A) removed
from the canopy and universal backplate
assembly, referred to in Step 2 under the
Mounting Instructions. This will allow access
to the threaded stem (G) at the center of the
canopy.

3. Insert the plug (E), located at the end of
the cable or reflector, into the center of the
threaded stem (G).

4. Slide the finished stem (D) over the plug (E)
and screw into place on the threaded stem
(G).

G

D

LICHTSTAR Single Canopy

No. C-8110 & C-8120

E

C-8110

C-8120

Diagram shows Canopy C-8120 with a cable

assembly.

Major lamp parts manufactured in Germany by Holtkötter Leuchten GmbH.

Bulbs manufactured in Germany by Osram GmbH. Final assembly by Holtkötter in South Saint Paul, MN.

Care Instructions

Use only a soft, dry cloth to clean. If necessary, a slightly damp, soft cloth can be used to spot

clean. Do not use common household cleaners on lamps or fixtures, as the lacquer on the

outside of the brass may be damaged as a result. Enjoy your new Holtkötter lamp.

Holtkötter ® and Holtkötter Leuchten® are registered trademarks of Holtkötter. All Rights Reserved.

© Holtkötter

ASSEMBLY INSTRUCTIONS FOR

e-mail: [e-mail]

www.holtkoetter.com

MOUNTING INSTRUCTIONS

Please note: if a dimmer is required, it is recommended that a Lutron ELV (Electronic Low
Voltage) dimmer be used. It is recommended that this fixture be installed and hung by a

licensed electrician.

1. Disconnect the power to the outlet box before servicing.

2. Unscrew the nut (A) holding the finished backplate (B) to the mounting hardware / crossbar
strap (C), allowing access to the crossbar strap (C).

3. Connect the wires from the canopy with the wires in the outlet box according to generally
accepted electrical standards.

4. Screw the crossbar strap (C) to the outlet box.

5. Secure the finished backplate (B) to the ceiling or canopy by attaching the quick-connect
reflector or glass of your choice (diagram and instructions on reverse).

6. The nut (A), removed in Step 2 can be discarded.

C

B

C

B

LICHTSTAR Single Canopy

No. C-8110 & C-8120

BULB INSTALLATION: S-006 SUSPENSION KIT

CAUTION: DISCONNECT POWER BEFORE
SERVICING.

1. Install the bulb into the socket. Be sure to use
the plastic wrap provided with the new bulb to
ensure long bulb life. Push the bulb firmly into
the socket.

2. The recommended replacement bulbs for

this fixture are 50 Watt Halostar IRC bulbs by

Osram, Holtkötter Item No. 9250*050-HSTAR.

Use of other brands of unknown quality may

cause a risk of overheating.

GLASS INSTALLATION

3. Slide the glass over the socket. Using the plastic
nut driver provided, insert the nut driver on the
inside of the glass and tighten the nut until the

glass is snug against the fixture.

4. Make sure the glass is secure, but not over­tightened.

A

C-8110

Major lamp parts manufactured in Germany by Holtkötter Leuchten GmbH.

Bulbs manufactured in Germany by Osram GmbH. Final assembly by Holtkötter in South Saint Paul, MN.

C-8120

A

For Holtkötter Glass G-5770, please refer to the

instructions provided with the glass kit.

Holtkötter ® and Holtkötter Leuchten® are registered trademarks of Holtkötter. All Rights Reserved.

© Holtkötter