Holtkoetter 6552P1 User Manual

ASSEMBLY INSTRUCTIONS FOR

205 Hardman Avenue South, South Saint Paul, MN 55075

Voice: [phone] • Fax: [phone]

e-mail: [e-mail]

www.holtkoetter.com

CAUTION, IMPORTANT SAFETY INSTRUCTIONS

This portable luminaire has a polarized plug (one blade is wider than the other) as a feature to
reduce the risk of electrical shock. This plug will fit a polarized outlet only one way. If the plug does
not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.

Never use with an extension cord unless plug can be fully inserted. Do not alter the plug.

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC
SHOCK, EXPOSURE TO EXCESSIVE UV RADIATION OR

Congratulations, you have just purchased the leading-edge dimming technology from Holtkötter

International, Inc. We have specifically designed the “Dimm System Punkt 1” (Dimming System
Point 1 (P1)) to provide specialized features for ease and convenience of use.

Features of the “Dimm System Punkt 1” include:

Point Dimming - the lamp may be turned on

with a single click of the P1 dimmer.

Soft On - the lamp will come on low and
continue to brighten to full brightness. This
allows the eye to adjust to a gradual increase
in light.

INJURY TO PERSONS

Soft / Delayed Off - turn the lamp off with a

single click of the P1 dimmer. The lamp will

WARNING - To reduce the risk of FIRE, ELECTRIC SHOCK,
EXPOSURE TO EXCESSIVE UV RADIATION OR INJURY TO
PERSONS:

1. Turn off power/unplug and allow to cool before replacing bulb.

2. Bulb gets HOT quickly. Contact only switch/plug when turning on.

3. Do not remain in light if skin feels warm.

4. Do not look directly at lighted lamp.

5. Keep lamp away from materials that burn.

6. Use only with a 60 Watt or smaller bulb.

7. Do not touch the bulb at any time. Use a soft cloth. Oil from skin may damage bulb.

8. Do not operate the portable luminaire with a missing or damaged guard, lamp containment
barrier or UV filter.

SAVE THESE INSTRUCTIONS

dim to 60% brightness of the original setting,

remaining briefly at that level to allow you to

exit the room; then the lamp gradually turns
itself off. This “soft” off provides a few moments

of light after turning the lamp off, rather than
immediate darkness as is the case with other
switches.

Dimming Cycle - to adjust the lamp to the
perfect light level for any situation, press and

hold the P1 dimmer. The dimmer will cycle
through all dimming levels. When the lamp

achieves the light level of your choice, release

the P1 dimmer.

Care Instructions

Use only a soft, dry cloth to clean. If necessary,
a slightly damp, soft cloth can be used to

spot clean. Do not use common household
cleaners on lamps or fixtures, as the lacquer on

the outside of the brass may be damaged as
a result.

Halogen Table Lamp

No. 6552*P1

Major lamp parts manufactured in Germany by Holtkötter Leuchten GmbH.

Bulbs manufactured in Germany by Osram GmbH. Final assembly by Holtkötter in South Saint Paul, MN.

Holtkötter ® and Holtkötter Leuchten® are registered trademarks of Holtkötter. All Rights Reserved.

© Holtkötter

ASSEMBLY INSTRUCTIONS FOR

e-mail: [e-mail]

www.holtkoetter.com

Please make sure the following parts are included:

1. Lamp Base (A) with Punkt1 (*P1) dimmer (D)

2. Bulb (B): 60 Watt Halopin, Frosted (Order Code: 9250*060-HPNFR)

3. Glass Shade (C)

Install the Bulb and Glass Shade

1. Install the new bulb, being careful not to touch the bulb envelope with your bare
hands. Insert it into the socket and push it down.

2. Once the bulb is installed, place the threaded end of the glass over the bulb and
onto the socket.

3. Screw the glass shade down on the fixture until it is firmly in place.

4. Your lamp is now operational.

Note of Caution

The recommended replacement bulb for this fixture is the 60 Watt Halopin bulb (frosted).

Replace the Fuse

An integrated fuse to protect the dimming circuit can be found in the box housing the plug.

Please check the fuse first, in case the lamp does not come on. A four (4) Amp replacement fuse
can be found on the Holtkoetter parts website: http://www.holtkoetter.com/products/parts/

fuse-4amp.aspx or at your local automotive or electronics parts store.

Halogen Table Lamp

No. 6552*P1

C

B

1. Unscrew the screws (G) located on each corner of the plug housing (E).

2. Open the housing to reveal the circuit board.

3. Locate the black box inside labeled
Fuse 5 x 20 (F) and open it.

4. Remove and discard old fuse;
replace with the new fuse.

5. Close the small fuse box and the plug
housing.

6. Replace and tighten the four screws
on the outside of the plug housing.

Major lamp parts manufactured in Germany by Holtkötter Leuchten GmbH.

Bulbs manufactured in Germany by Osram GmbH. Final assembly by Holtkötter in South Saint Paul, MN.

FG E

A

D

Holtkötter ® and Holtkötter Leuchten® are registered trademarks of Holtkötter. All Rights Reserved.

© Holtkötter