Holtkoetter 5701 User Manual

ASSEMBLY INSTRUCTIONS FOR

205 Hardman Avenue South, South Saint Paul, MN 55075

Voice: [phone] • Fax: [phone]

e-mail: [e-mail]

www.holtkoetter.com

HEIGHT ADJUSTMENT (Diagram A)

The height of this fixture can be adjusted at any time.

1. Hold the weight of the glass off the cables.

2. Squeeze the center adjustment bar together to
release the cables. See Diagram A.

3. Adjust the height.

4. Release the center adjustment bar when the

height is acceptable.

CABLE LENGTH ADJUSTMENT (Diagram B & Diagram C)

1. Be sure to support or remove the glass reflector
prior to shortening the cables.

2. Using the allen wrench provided in the packet
with the bulb and wire crimps, loosen each side
of the counter-weight to release the cable from

the fixture. See Diagram B.

3. Cut the cable to the correct length on each
side.

4. Slide the wire crimps over the cut end of the
cable and crimp to secure. If the wire crimp
is too long to fit completely into the counter­weight, cut off a small amount and re-fit.

5. Insert the cable back into the counter-weight
and tighten the set screws with the allen wrench.

The set screw should tighten flush to the fixture.

See Diagram C.

Low-voltage Pendant

No. 5701

Diagram A

Diagram B

Diagram C

5701/1 B10 5701/1 B20

Major lamp parts manufactured in Germany by Holtkötter Leuchten GmbH.

Bulbs manufactured in Germany by Osram GmbH. Final assembly by Holtkötter in South Saint Paul, MN.

Care Instructions

Use only a soft, dry cloth to clean. If necessary, a slightly damp, soft cloth can be used to spot

clean. Do not use common household cleaners on lamps or fixtures, as the lacquer on the

outside of the brass may be damaged as a result. Enjoy your new Holtkötter lamp.

Holtkötter ® and Holtkötter Leuchten® are registered trademarks of Holtkötter. All Rights Reserved.

© Holtkötter

ASSEMBLY INSTRUCTIONS FOR

e-mail: [e-mail]

www.holtkoetter.com

Please make sure that the following parts for your fixture are enclosed:

1. Fixture with backplate and hanging hardware.

2. Bulb: 50 Watt Halostar IRC by Osram, GY6.35 base

3. Allen Wrench

4. Wire Crimps (2 each)

5. Glass

6. Plastic Nut Driver

7. If a dimmer is required, it is recommended that a Lutron ELV (Electronic Low Voltage)
dimmer be used.

It is recommended that this fixture be installed and hung by a licensed
electrician.

HANGING INSTRUCTIONS

1. Be sure to disconnect the power to the outlet box.

2. Unscrew the four (4) stem screws (A) below the
backplate, allowing access to the crossbar strap
and mounting plate.

3. Connect the wires and ground wire according to
generally accepted electrical standards.

4. Screw the crossbar strap/mounting plate to the

outlet box.

5. Secure the backplate to the fixture by screwing the
four (4) stem screws back into place.

Low-voltage Pendant

No. 5701

BULB INSTALLATION / REPLACEMENT

CAUTION: DISCONNECT POWER BEFORE SERVICING.

Install the bulb into the socket. Be sure to use the plastic wrap
provided with the new bulb to ensure long bulb life. Push the
bulb firmly into the socket.

The recommended replacement bulbs for this fixture are 50
Watt Halostar IRC bulbs by Osram.

Use of other brands of unknown quality may cause a risk of
overheating.

Holtkötter Item No. 9250*050-HSTAR

GLASS INSTALLATION

Slide the glass over the socket. Using the plastic nut driver
provided, insert the nut driver on the inside of the glass and

tighten the nut until the glass is snug against the fixture.

Please note: if the glass doesn’t hang straight, the socket may be adjusted slightly

within the hole of the glass. Once readjusted, be sure to tighten until secure.

(A)

Major lamp parts manufactured in Germany by Holtkötter Leuchten GmbH.

Bulbs manufactured in Germany by Osram GmbH. Final assembly by Holtkötter in South Saint Paul, MN.

Holtkötter ® and Holtkötter Leuchten® are registered trademarks of Holtkötter. All Rights Reserved.

© Holtkötter