Holtkoetter 5517 User Manual
ASSEMBLY INSTRUCTIONS FOR
205 Hardman Avenue South, South Saint Paul, MN 55075
Voice: (800) 899-5444 • Fax: (888) 552-8661
e-mail: customerservice@holtkoetter.com
www.holtkoetter.com
Install the Bulbs & Glass (Diagram 4)
1. The bulbs provided with this fixture are specialty low-
voltage bulbs by Osram, the Halostar Starlite. Insert the
bulbs (M) into the sockets. NOTE: BE CAREFUL NOT TO
TOUCH THE BULB WITH YOUR BARE HANDS.
CAUTION: Always remember to disconnect power to
the fixture before replacing bulbs to prevent damage
to the bulbs.
2. Using the plastic socket driver (O) provided, screw each
glass shade (N) onto the fixture until it is snug. Do not
overtighten.
M
CSA/UL SAFETY REQUIREMENTS
CSA/UL requires that these IMPORTANT SAFETY INSTRUCTIONS be listed:
Low-voltage Halogen Pendant
No. 5517
Diagram 4
M
N
O
INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY
LIGHTED LAMP IS HOT!
WARNING: TO REDUCE THE RISK OF FIRE OR INJURY, PLEASE FOLLOW THESE SAFETY INSTRUCTIONS:
1. Turn off power and allow to cool before replacing lamps.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Keep lamp away from materials that may burn.
4. Do not touch lamp at any time. Use a soft cloth. Oil from skin may damage lamp.
5. Do not operate luminaire with missing or damaged glass.
6. CAUTION: The recommended replacement bulbs for this fixture are 20 Watt Halostar
bulbs by Osram. Use of other brands of unknown quality may cause a risk of
overheating.
Major lamp parts manufactured in Germany by Holtkötter Leuchten GmbH.
Bulbs manufactured in Germany by Osram GmbH. Final assembly by Holtkötter in South Saint Paul, MN.
5517/7
Care Instructions
Use only a soft, dry cloth to clean. If necessary, a slightly damp, soft cloth can be used to spot
clean. Do not use common household cleaners on lamps or fixtures, as the lacquer on the
outside of the brass may be damaged as a result. Enjoy your new Holtkötter lamp.
Holtkötter ® and Holtkötter Leuchten® are registered trademarks of Holtkötter. All Rights Reserved.
© Holtkötter
ASSEMBLY INSTRUCTIONS FOR
e-mail: customerservice@holtkoetter.com
www.holtkoetter.com
Please make sure that the following parts for your low-voltage pendant
are enclosed:
1. Fixture including ceiling canopy, frame and height
adjustment bar.
2. Additional backplate and universal crossbar strap
3. Glass shades
4. Bulbs for 5517/7: 7 ea x 20 Watt Halostar by Osram,
GY6.35 base. Order Code: 9250*020-HSTAR
This fixture utilizes an electronic, line-voltage (120
V input) to low-voltage (12 V output) transformer by
LIGHTECH, rated at 175 Watts for the 5517/7, allowing
for a 20 Watt maximum per bulb.
If you are planning to use a dimmer with this fixture,
we recommend using a Lutron ELV (electronic low
voltage) style dimmer.
NOTE: The electronic transformer by LIGHTECH is equipped with an automatic reset switch.
If the fixture is not working or has created a short, disconnect the power to the fixture and the
transformer will reset itself.
Diagram 3
Diagram 2
Be sure to turn off the circuit breaker before installing this fixture.
Dry location only.
THIS PRODUCT MUST BE INSTALLED IN
Diagram 1
ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON FAMILIAR
WITH CONSTRUCTION AND OPERATION OF
THE PRODUCT AND THE HAZARDS INVOLVED.
Mounting Instructions (Diagram 1)
Parts used:
A) Round 5” decorative plate with universal crossbar
B) Long metal strap with screws
C) Two brass tubular nuts
D) Two decorative knobs.
C
A
B
D
Low-voltage Halogen Pendant
No. 5517
Mounting Instructions, continued
1. Disconnect power to the box before installation.
2. Remove decorative knobs (D) and the brass tubular nuts (C) that are located under
the decorative knobs (D).
3. Remove the long metal strap (B) located on the top of canopy.
4. Mount the round decorative plate (A) to the metal strap with screws provided on the
universal crossbar strap, then mount the assembled piece to the outlet box.
5. Connect the wires from the fixture with the wires in the outlet
box according to generally accepted electrical standards.
Determine the polarity of the cord by rubbing it with your
thumb. One side will feel smooth (= hot/black) and the
other side will feel rough (= cold/white).
6. Slide the canopy over the metal strap and secure with brass
tubular screws (C).
7. Finally put decorative knobs (D) on the bottom of the
canopy.
Fixture Cable Length Adjustment (Diagram 2)
This low-voltage pendant cannot be lengthened in the field.
Due to the nature of this support system, fixtures requiring longer
support cables will have to be special ordered.
This fixture is supported by two separate cables connected to the
fixture at the finished cable holder (E).
1. Locate the nut (J) at the bottom of the cable holder. Take
the weight off the fixture and unscrew the nut (J).
2. Remove the horizontal cable (H) from the cable holder.
3. Pull the vertical cable (G) down to reveal the cable guide
(F). Pull enough cable through the guide to correct the
height. Cut the support cable off to the correct length.
4. Replace the horizontal cable (H). Pull the vertical cable (G)
back up into place.
5. Screw the cable holder nut (J) back in place.
Fixture Height Adjustment (Diagram 3)
The center bar (K) between the canopy and the fixture can be
raised or lowered to adjust the overall height of the fixture. Press
the knobs (L) at each end of the center bar simultaneously to
raise or lower the fixture to the desired height.
Diagram 2
F
Diagram 3
L
E
G
H
J
K
Major lamp parts manufactured in Germany by Holtkötter Leuchten GmbH.
Bulbs manufactured in Germany by Osram GmbH. Final assembly by Holtkötter in South Saint Paul, MN.
Holtkötter ® and Holtkötter Leuchten® are registered trademarks of Holtkötter. All Rights Reserved.
© Holtkötter
Loading...