Holtkoetter 5506 User Manual
ASSEMBLY INSTRUCTIONS FOR
205 Hardman Avenue South, South Saint Paul, MN 55075
Voice: (800) 899-5444 • Fax: (888) 552-8661
e-mail: customerservice@holtkoetter.com
www.holtkoetter.com
Install the Bulbs & Glass (Diagram 3)
1. The bulbs provided with this fixture
are specialty low-voltage bulbs
by Osram, the Halostar Starlite.
Insert the bulbs (J) into the sockets.
NOTE: BE CAREFUL NOT TO TOUCH
THE BULB WITH YOUR BARE HANDS.
CAUTION: Always remember to
disconnect power to the fixture before replacing
bulbs to prevent damage to the bulbs.
2. Using the plastic socket driver (L) provided, screw each
glass shade (K) onto the fixture until it is snug. Do not
overtighten.
J
CSA/UL SAFETY REQUIREMENTS
CSA/UL requires that these IMPORTANT SAFETY INSTRUCTIONS
be listed:
INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY
LIGHTED LAMP IS HOT!
Low-voltage Halogen Pendant
No. 5506
J
K
L
Diagram 3
WARNING: TO REDUCE THE RISK OF FIRE OR INJURY, PLEASE FOLLOW THESE SAFETY INSTRUCTIONS:
1. Turn off power and allow to cool before replacing lamps.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Keep lamp away from materials that may burn.
4. Do not touch lamp at any time. Use a soft cloth. Oil from skin may damage lamp.
5. Do not operate luminaire with missing or damaged glass.
6. CAUTION: The recommended replacement bulbs for this fixture are 20 Watt Halostar
bulbs by Osram. Use of other brands of unknown quality may cause a risk of
overheating.
Major lamp parts manufactured in Germany by Holtkötter Leuchten GmbH.
Bulbs manufactured in Germany by Osram GmbH. Final assembly by Holtkötter in South Saint Paul, MN.
5506/6
Care Instructions
Use only a soft, dry cloth to clean. If necessary, a slightly damp, soft cloth can be used to spot
clean. Do not use common household cleaners on lamps or fixtures, as the lacquer on the
outside of the brass may be damaged as a result. Enjoy your new Holtkötter lamp.
Holtkötter ® and Holtkötter Leuchten® are registered trademarks of Holtkötter. All Rights Reserved.
© Holtkötter
ASSEMBLY INSTRUCTIONS FOR
e-mail: customerservice@holtkoetter.com
www.holtkoetter.com
Please make sure that the following parts for your low-voltage pendant are
enclosed:
1. Fixture including ceiling canopy, frame and counterweight.
2. Additional backplate and universal crossbar strap
3. Glass shades
4. Bulbs for 5506/6: 6 ea x 20 Watt Halostar by Osram, GY6.35 base.
Order Code: 9250*020-HSTAR
This fixture utilizes an electronic, line-voltage (120 V input) to low-voltage (12 V output)
transformer by LIGHTECH rated at 175 Watts, allowing for a 20 Watt maximum per bulb.
If you are planning to use a dimmer with this fixture, we recommend using a Lutron ELV
(electronic low voltage) style dimmer.
NOTE: The electronic transformer by LIGHTECH is equipped with an automatic reset switch. If
the fixture is not working or has created a short, disconnect the power to the fixture and the
transformer will reset itself.
Be sure to turn off the circuit breaker before installing this fixture.
Dry location only.
Diagram 1
THIS PRODUCT MUST BE INSTALLED IN
A
ACCORDANCE WITH THE APPLICABLE
INSTALLATION CODE BY A PERSON
FAMILIAR WITH CONSTRUCTION AND
OPERATION OF THE PRODUCT AND
B
THE HAZARDS INVOLVED.
Mounting Instructions (Diagram 1)
Parts used:
A) Round 5” decorative plate with universal
crossbar
B) Long metal strap with screws
C) Two brass tubular nuts
D) Two decorative knobs.
C
D
Low-voltage Halogen Pendant
No. 5506
Mounting Instructions, continued
1. Disconnect power to the box before installation.
2. Remove decorative knobs (D) and the brass tubular nuts (C) that are located under
the decorative knobs (D).
3. Remove the long metal strap (B) located on the top of canopy.
4. Mount the round decorative
plate (A) to the metal strap
with screws provided on the
universal crossbar strap, then
mount the assembled piece
to the outlet box.
5. Connect the wires from the
fixture with the wires in the outlet
box according to generally accepted
electrical standards. Determine the polarity of
the cord by rubbing it with your thumb. One side
will feel smooth (= hot/black) and the other side will
feel rough (= cold/white).
6. Slide the canopy over the metal strap and secure with brass
tubular screws (C).
7. Finally put decorative knobs (D) on the bottom of the
canopy.
Fixture Cable Length Adjustment (Diagram 2)
This low-voltage pendant cannot be lengthened in the field.
Due to the nature of this support system, fixtures requiring
longer support cables will have to be special ordered.
This fixture is supported by two separate cables connected
to the fixture at the finished cable holder (E). The vertical
cable can be shortened.
1. Locate the nut (F) at the bottom of the cable holder.
Take the weight off the fixture and unscrew the nut (F).
2. Pull the vertical cable (G) down to reveal the cable
guide (H). Pull enough cable through the guide to
correct the height. Cut the support cable off to the
correct length.
3. Pull the vertical cable (G) back up into place.
4. Screw the cable holder nut (F) back in place.
Diagram 3
Diagram 2
Diagram 2
G
F
E
H
Major lamp parts manufactured in Germany by Holtkötter Leuchten GmbH.
Bulbs manufactured in Germany by Osram GmbH. Final assembly by Holtkötter in South Saint Paul, MN.
Holtkötter ® and Holtkötter Leuchten® are registered trademarks of Holtkötter. All Rights Reserved.
© Holtkötter
Loading...