Holtkoetter 3502 User Manual

ASSEMBLY INSTRUCTIONS FOR

205 Hardman Avenue South, South Saint Paul, MN 55075

Voice: [phone] • Fax: [phone]

e-mail: [e-mail]

www.holtkoetter.com

UL SAFETY REQUIREMENTS

Underwriter’s Laboratories requires that these IMPORTANT SAFETY INSTRUCTIONS be listed:

INSTRUCTIONS PERTAINING TO RISK OF FIRE OR INJURY

LIGHTED LAMP IS HOT!

WARNING: TO REDUCE THE RISK OF FIRE OR INJURY, PLEASE FOLLOW THESE SAFETY INSTRUCTIONS:

1. Turn off power and allow to cool before replacing lamps.

2. Lamp gets HOT quickly! Contact only switch/plug when turning on.

3. Keep lamp away from materials that may burn.

4. Do not touch lamp at any time. Use a soft cloth. Oil from skin may damage lamp.

5. Do not operate luminaire with missing or damaged glass.

6. CAUTION: The recommended replacement bulbs for this fixture are 60 Watt Halopin
bulbs by Osram. Use of other brands of unknown quality may cause a risk of

overheating.

Ceiling Fixtures

No. 3502, No. 3503 & No. 3505

Major lamp parts manufactured in Germany by Holtkötter Leuchten GmbH.

Bulbs manufactured in Germany by Osram GmbH. Final assembly by Holtkötter in South Saint Paul, MN.

Care Instructions

Use only a soft, dry cloth to clean. If necessary, a slightly damp, soft cloth can be used to spot

clean. Do not use common household cleaners on lamps or fixtures, as the lacquer on the
outside of the brass may be damaged as a result. Enjoy your new Holtkötter fixture.

Holtkötter ® and Holtkötter Leuchten® are registered trademarks of Holtkötter. All Rights Reserved.

© Holtkötter

ASSEMBLY INSTRUCTIONS FOR

e-mail: [e-mail]

www.holtkoetter.com

Please make sure that the following parts for ceiling fixture are enclosed:

1. Fixture including backplate

2. Glass shade

3. Bulb Kit including:

A. Finished Trim Ring (Solid or Dekor)

B. Optional plastic washers (to lower the glass if desired)

C. 5mm Hex Key

D. Bulbs:

3502/2 - 120 Watts, total (2 ea x max. 60 Watt)
3503/3 - 180 Watts, total (3 ea x max. 60 Watt)
3505/5 - 300 Watts, total (5 ea x max. 60 Watt)

60 Watt Halopin by Osram
Order Code: 9250*060-HPNFR

Be sure to turn off the circuit breaker before installing this fixture.
It is recommended that this fixture be installed and hung by a licensed

electrician.

Mounting Instructions

1. Disconnect power to the outlet box before installation.

2. Loosen screw (A) to release the fixture from the
backplate (B).

3. Mount the backplate (B) to the outlet box.

4. Connect the wires from the fixture with the wires in the

outlet box according to generally accepted electrical

standards.

5. Slip the fixture onto the backplate (B). Using a phillips

head screwdriver, secure the fixture to the outlet box by

tightening the screw (A).

(A)

Ceiling Fixtures

No. 3502, No. 3503 & No. 3505

Install the Bulbs

1. Before reconnecting power to the box, install the bulbs.

2. Install each bulb (C), being careful not to touch the bulb envelop with bare hands.
Hold the bulb and push straight into the socket.

(Photos represent a sample of fixture 3505/5. The fixture you are installing may only have 2
(3502/2) or 3 (3503/3) bulbs.)

(C)

Install the Glass Shade

1. Install the glass shade on the fixture, centering the aluminum nut (D) on the fixture.

2. OPTIONAL: If desired, the glass can be lowered by installing the additional plastic
washers provided. Prior to installation, set one or two washers on the aluminum screw
inside the glass shade.

3. Using the 5mm hex key (E) provided, screw the glass shade onto the middle stem of

the fixture. Hand-tighten to secure the glass to the fixture. Do not overtighten.

4. Install the finished disc (F) by screwing it into place in the center of the aluminum nut
(D).

(D) (E) (F)

(B)

Major lamp parts manufactured in Germany by Holtkötter Leuchten GmbH.

Bulbs manufactured in Germany by Osram GmbH. Final assembly by Holtkötter in South Saint Paul, MN.

Holtkötter ® and Holtkötter Leuchten® are registered trademarks of Holtkötter. All Rights Reserved.

© Holtkötter