Holtkoetter 2508 User Manual
ASSEMBLY INSTRUCTIONS FOR
205 Hardman Avenue South, South Saint Paul, MN 55075
Voice: (800) 899-5444 • Fax: (888) 552-8661
e-mail: customerservice@holtkoetter.com
www.holtkoetter.com
CAUTION, IMPORTANT SAFETY INSTRUCTIONS
This portable luminaire has a polarized plug (one blade is wider than the other) as a feature to
reduce the risk of electrical shock. This plug will fit a polarized outlet only one way. If the plug does
not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician.
Never use with an extension cord unless plug can be fully inserted. Do not alter the plug.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC
SHOCK, EXPOSURE TO EXCESSIVE UV RADIATION OR
INJURY TO PERSONS
WARNING - To reduce the risk of FIRE, ELECTRIC SHOCK,
Please make sure that the following parts for your lamp are enclosed:
1. Reflector
2. Aluminum Ring (attached to lamp)
3. Glass Shield
4. Allen Wrench (packed inside bulb box)
5. Large Washer (2 each, already installed)
6. Handle with plastic protector
7. Small Plastic Washer (attached to reflector)
8. Small Plastic Nut (attached to reflector)
9. Bayonet Base Halogen Bulb
10. Floor Lamp
11. Foot Dimmer
EXPOSURE TO EXCESSIVE UV RADIATION OR INJURY TO
PERSONS:
Halogen Pharmacy Lamp
No. 2508
1. Turn off power/unplug and allow to cool before replacing bulb.
2. Bulb gets HOT quickly. Contact only switch/plug when turning on.
3. Do not touch hot lens, guard or enclosure.
4. Do not remain in light if skin feels warm.
5. Do not look directly at lighted lamp.
6. Keep lamp away from materials that burn.
7. Use only with a 100 Watt, bayonet base halogen bulb or smaller bulb.
8. Do not touch the bulb at any time. Use a soft cloth. Oil from skin may damage bulb.
9. Do not operate the portable luminaire with a missing or damaged guard, lamp containment
barrier or UV filter.
SAVE THESE INSTRUCTIONS
Major lamp parts manufactured in Germany by Holtkötter Leuchten GmbH.
Bulbs manufactured in Germany by Osram GmbH. Final assembly by Holtkötter in South Saint Paul, MN.
Care Instructions
Use only a soft, dry cloth to clean. If necessary, a slightly damp, soft cloth may be used
to spot clean. Do not use common household cleaners or brass cleaners on lamps
or fixtures, as the lacquer on the outside of the brass may be damaged as a result.
Enjoy your new Holtkötter lamp.
Holtkötter ® and Holtkötter Leuchten® are registered trademarks of Holtkötter. All Rights Reserved.
© Holtkötter
ASSEMBLY INSTRUCTIONS FOR
e-mail: customerservice@holtkoetter.com
Install the Bulbs and Shades
Step 1.
Set Screw
BE
Step 2.
A
BE
www.holtkoetter.com
The brass arms are made of soft, high-quality brass that
is pliable and may be bent from shipping. If necessary,
apply pressure to straighten.
Loosen the set screw with the allen wrench (D). Then
unscrew the aluminum ring (B) from the lamp arm.
Remove one of the large washers (E).
Note: the shade is shipped with the handle in place.
Prior to installation of the shade, remove the handle,
the small plastic nut and the small plastic washer.
These will be reinstalled after installing the bulb and
glass shield.
Slide the shade (A) over the socket. Place the large
washer (E) that was removed in Step 1 back onto the
socket. Screw the aluminum ring (B) back onto the
socket until it is tight.
Step 4.
Step 5.
Halogen Pharmacy Lamp
No. 2508
Put the 100-Watt halogen bulb (I) into the socket. Hold
the bulb at the porcelain grip, push it down slightly and
turn it clockwise.
BE CAREFUL NOT TO TOUCH THE BULB ENVELOPE WITH
YOUR BARE HANDS.
I
Note: the small plastic nut and small plastic washer
that were removed in Step 2 will be needed for this
step.
H
G
Align the glass shield (C) with the small screw extending
from the bottom of the shade. Place the small washer
(G) and the small plastic nut (H) over the screw and
finger tighten.
C
Step 3.
Using the allen wrench (D), tighten the set screw on the
aluminum ring into place.
DO NOT OVERTIGHTEN. MAKE SURE THE SHADE IS STILL
LOOSE ENOUGH TO TURN.
D
Major lamp parts manufactured in Germany by Holtkötter Leuchten GmbH.
Bulbs manufactured in Germany by Osram GmbH. Final assembly by Holtkötter in South Saint Paul, MN.
Step 6.
Note: the handle that was removed in Step 2 will be
F
needed for this step.
Next, screw on the handle (F) and finger tighten.
DO NOT OVERTIGHTEN – THE GLASS SHIELD MAY CRACK
UNDER TOO MUCH PRESSURE.
Step 7.
Plug the lamp cord into the wall outlet. Your lamp is now operational.
Holtkötter ® and Holtkötter Leuchten® are registered trademarks of Holtkötter. All Rights Reserved.
© Holtkötter
Loading...