HOLOVISION 401-S12-PAN, 410-S12-PAN, 404-S12-PAN, 411-S12-PAN, 403-S12-PAN Installation Instructions Manual

INSTALLATION

Manual Type 6.2.0.1-RF

“Panasonic Compatible” Unit with Essex

“S-12 Stand - Alone” Keypad

For Models

400-S12-PAN 401-S12-PAN
403-S12-PAN 404-S12-PAN
410-S12-PAN 411-S12-PAN

Specifications

Communication

For use with all Panasonic KSUs with door phone
card. This unit is a replacement for the Panasonic
KXT-30865 door phone.

INSTRUCTIONS

Access Control

Essex “stand-alone” 12 button keypad
1 relay plus 2 grounding outputs
(external relays required)
500 users
12 VDC power supply included

Intercom to KSU

Not Used

12 VDC input (for camera and keypad)

NO, COM, NC relay connections

Keypad case ground

Remote bypass terminals (activate relay)

Connect tamper switch to alarm (optional)

501 E. Goetz Ave.

Santa Ana, Ca 92707

www.eholovision.com

Ph. 714-434-6904

Fax [phone]

HOLOVISION

Loop for Strike Power

Cut for NO Contact Closure

400 Series “S-12” Junction Board

Essex Keypad Wiring

In

e

n

i

L

O

C

KSU

DC Out for Gate Strike

To Ph on e s

Strike 1

Door 1

12vDC

1.5 A

Gate Strike

NOTE: MOV (metal oxide varistor) is the small red component which is included. Its purpose is to absorb “inductive kick

back” which can be created when power is removed from the strike.

Loop is required from DC positive to contact common for DC voltage to strike.

Page 2 Type 6.2.0.1-RF

*M

OV

AC Loop for Strike

Cut for NO Contact Closure

i

s

r

ec

o

m

m

e

nd

e

d

Remote

Bypass

Button

Essex Keypad Wiring

In

e

n

i

L

O

C

KSU

Contact Closure for Gate Operation

To Ph on e s

Strike 1

Door 1

12vDC

1.5 A

Page 3 Type 6.2.0.1-RF

AC Loop for Strike

Cut for NO Contact Closure

Programming the Essex Keypad

Set Keypad Illumination to ON ALL OF THE TIME

STEP ACTION BEEP Red LED Green LED

1 Remove power

2 Jumper the “CONFIG” pins on the rear of the keypad . V = 12

3 Apply 12 VDC power to red and black wires Quadruple Beep Flash Solid

4 Enter

5 Enter

6 Remove power

7 Remove “CONFIG” jumper

8 Reapply power

followed by

9 9

2 1 4

#

followed by

Double Beep Flash Solid

#

Triple Beep Flash Solid

Set Master Code

STEP ACTION BEEP Red LED Green LED

1

2 Enter

3 Enter

4 Enter new master code, followed by

5 Enter

6 EXAMPLE: old code is 123, new code is 456

The default Master Code is

This can be changed to a unique code 3 - 8 digits long

3 1 2 3 #

*

1

#

* *

“123”

#

.

Double Beep Fast Flash Solid

Double Beep Fast Flash Slow Flash

Triple Beep Fast Flash Solid

Double Beep

3 1 2 3 # 1 # 4 5 6 #

*

* *

Note: If the User ID, or User Code/PIN has already been assigned, you will hear one long beep when # is entered.

In this case, choose a different User ID / PIN, or see the instructions for changing or deleting codes.

DEFAULT USER CODE & MASTER CODE IS “123#”

TYPE 6.2.0.1-RF Page 4

Programming the Essex Keypad

Set User Codes

STEP ACTION BEEP Red LED Green LED

1 The Master Code is necessary to do this step.

2 Enter

3 Enter

4 Enter 1st User ID (1-500), followed by

5 Enter 1st User Code/PIN, followed by

6 Enter #to complete User 1 programming Triple Beep Slow Flash Slow Flash

7 Enter 2nd User ID (1-500), followed by

8 Enter 2nd User Code/PIN, followed by

9 Enter #to complete User 2 programming Triple Beep Slow Flash Slow Flash

10 Enter

Example for entering user code 1 and 2- * 1 1 2 3 # 1 # 1# 4 5 6 # # 2 # 7 8 9 # # * * * *

Changing User Codes - using User ID

Master Code “123” is used as an example.

1 1 2 3

*

1

#

#

#

#

#

#

* * * *

Double Beep Slow Flash Solid

N

N

N

Double Beep Slow Flash Slow Flash

Double Beep Slow Flash Fast Flash

Double Beep Slow Flash Fast Flash

N

Double Beep Slow Flash Fast Flash

Double Beep Slow Flash Fast Flash

Double Beep X 2

STEP ACTION BEEP Red LED Green LED

1 The Master Code is necessary to do this step.

Master Code “123” is used as an example.

2 Enter

3 Enter

4 Enter User ID to be changed (1-500), followed by

5 Enter new User Code/PIN, followed by

6 Enter #to complete programming Triple Beep Slow Flash Slow Flash

7 Enter

Example for changing user code 1- * 1 1 2 3 # 2 # 1 # 7 8 9 # # * * * *

1 1 2 3

*

2

#

#

#

#

N

* * * *

* Note: If the User ID, or User Code/PIN has not been assigned, you will hear one long beep

N

Double Beep Slow Flash Solid

Double Beep Slow Flash Slow Flash

Double Beep Slow Flash Fast Flash

Double Beep Slow Flash Fast Flash

Double Beep X 2

when # is entered.

TYPE 6.2.0.1-RF Page 5

Programming the Essex Keypad

Deleting User Codes - using User Code/PIN

STEP ACTION BEEP Red LED Green LED

1 The Master Code is necessary to do this step.

In this example, the Master Code is 123

2 Enter

3 Enter

4 Enter User Code/PIN to be changed, followed by

5 Enter new User Code/PIN, followed by

6 Enter #to complete programming Triple Beep Slow Flash Slow Flash

7 Enter

Example for deleting user code # 456- * 1 1 2 3 # 5 # 4 5 6 # 7 8 9 # # * * * *

Deleting User Codes - using User ID

1 1 2 3

*

5

#

* * * *

#

N

#

#

Double Beep Slow Flash Solid

Double Beep Slow Flash Slow Flash

Double Beep Slow Flash Fast Flash

Double Beep Slow Flash Fast Flash

Double Beep X 2

STEP ACTION BEEP Red LED Green LED

1 The Master Code is necessary to do this step.

2 Enter

3 Enter

4 Enter 1st User ID to be deleted (1-500), followed by

In this example, the Master Code is 123

1 1 2 3

*

4

#

#

Double Beep Slow Flash Solid

Double Beep Slow Flash Slow Flash

N

#

Triple Beep Slow Flash Fast Flash

5 Enter 2nd User ID to be deleted (1-500), followed by

.

6 Enter

Example for deleting user ID 1 and 2- * 1 1 2 3 # 4 #1 # 2 # * * * *

* * * *

N

* Note: If the User ID, or User Code/PIN has not been assigned, you will hear one long beep

when # is entered.

#

N

Triple Beep Slow Flash Fast Flash

Double Beep X 2

Page 6 TYPE 6.2.0.1-RF

Programming the Essex Keypad

Reset Keypad to Factory Defaults--- This is not normally necessary, but can be done as follows

STEP ACTION BEEP Red LED Green LED

1 Remove power

2 Jumper the “CONFIG” pins on the rear of the keypad

3 Apply 12 VDC power to red and black wires ONLY Quadruple Beep Flash Solid

5 Enter

6 WAIT about 4 seconds Quadruple Beep Flash Solid

7 Enter

8 Remove power

9 Remove “CONFIG” jumper

10 Reapply power

Setting Main Relay Opening Time

0 0 9 9

9 9

#

#

Double Beep Flash 3 Sec Flash

Triple Beep Flash Solid

STEP ACTION BEEP Red LED Green LED

1 The default Master Code is “123”.

This can be changed to a unique code 3 - 8 digits long.

2 Enter

3 Enter

*3 1 2 3

2

#

#

Double Beep Slow Flash Solid

Double Beep Slow Flash Slow Flash

4 Enter the desired activation time in Seconds followed by

5 Enter

6 Example:

to exit

* *

2 # 10 #

(10 second activation time)

* *

Note: If the User ID, or User Code/PIN has not been assigned, you will hear one long beep

when # is entered.

#

Triple Beep Slow Flash Solid

Page 7 TYPE 6.2.0.1-RF

www.eholovision.com

501 E. Goetz Ave.

Santa Ana, Ca 92707

Ph. 714-434-6904

Fax [phone]