HOLOPHANE Predator LED Flood Medium, Predator LED Flood Large Installation And Maintenance Manual

WARNING

RISK OF ELECTRIC SHOCK

WARNING

RISK OF BURN

CAUTION

RISK OF INJURY

CAUTION

LED IMPORTANT SAFETY INSTRUCTIONS

• To reduce the risk of death, personal injury or property damage from fire, electric shock, falling parts, cuts/abrasions, and

other hazards please read all warnings and instructions included with and on the fixture box and all fixture labels.

• Before installing, servicing, or performing routine maintenance upon this equipment, follow these general precautions.

• Installation and service of luminaires should be performed by a qualified licensed electrician.

• Maintenance of the luminaires should be performed by person(s) familiar with the luminaires’ construction and operation

and any hazards involved. Regular fixture maintenance programs are recommended.

• It will occasionally be necessary to clean the outside of the refractor/lens. Frequency of cleaning will depend on ambient

dirt level and minimum light output which is acceptable to user. Refractor/lens should be washed in a solution of warm
water and any mild, non-abrasive household detergent, rinsed with clean water and wiped dry. Should optical assembly
become dirty on the inside, wipe refractor/lens and clean in above manner, replacing damaged gaskets as necessary.

• DO NOT INSTALL DAMAGED PRODUCT! This luminaire has been properly packed so that no parts should have been

damaged during transit. Inspect to confirm. Any part damaged or broken during or after assembly should be replaced.

• Recycle: For information on how to recycle LED electronic products, please visit www.epa.gov.

• These instructions do not purport to cover all details or variations in equipment nor to provide every possible contingency

to meet in connection with installation, operation, or maintenance. Should further information be desired or should
particular problems arise which are not covered sufficiently for the purchaser’s or owner’s purposes, this matter should be
referred to Acuity Brands Lighting, Inc.

SAVE THESE INSTRUCTIONS AND DELIVER TO OWNER AFTER INSTALLATION

READ AND FOLLOW ALL SAFETY INSTRUCTIONS!

 Disconnect or turn off power before

installation or servicing.

 Verify that supply voltage is correct by

comparing it with the luminaire label
information.

 Make all electrical and grounded

connections in accordance with the National
Electrical Code (NEC) and any applicable
local code requirements.

 All wiring connections should be capped

with UL approved recognized wire
connectors.

 Allow lamp/fixture to cool before handling.

Do not touch enclosure or light source.

 Do not exceed maximum wattage marked on

luminaire label.

 Follow all manufacturer’s warnings,

recommendations and restrictions for: driver
type, burning position, mounting
locations/methods, replacement and
recycling.

 Wear gloves and safety glasses at all times

when removing luminaire from carton,
installing, servicing or performing
maintenance.

 Avoid direct eye exposure to the light source

while it is on.

 Keep combustible and other materials that

can burn, away from lamp/lens.

 Do not operate in close proximity to persons,

combustible materials or substances
affected by heat or drying.

IM-365-A

CAUTION: RISK

OF PRODUCT DAMAGE

Please see product specific installation instructions for additional warnings or any applicable FCC or other regulatory

Failure to follow any of these instructions could void product warranties. For a complete listing of product Terms and

Our Brands Indoor/Outdoor Indoor Lighting Outdoor Lighting Controls

Lithonia Lighting Gotham American Electric Lighting DARK TO LIGHT

Carandini Mark Architectural Lighting Antique Street Lamps Lighting Control & Design
Holophane Peerless Hydrel ROAM
RELOC Renaissance Lighting Tersen Sensor Switch
Winona Lighting Synergy

Acuity Brands Lighting, Inc. assumes no responsibility for claims arising out of improper or careless installation or handling of its products.

 Never connect components under load.
 Do not mount or support these fixtures in a manner that can cut the outer jacket or damage wire

insulation.

 Unless individual product specifications deem otherwise: Never connect an LED product directly to a

dimmer packs, occupancy sensors, timing devices, or other related control devices. LED fixtures must be
powered directly off a switched circuit.

 Unless individual product specifications deem otherwise: Do not restrict fixture ventilation. Allow for

some volume of airspace around fixture. Avoid covering LED fixtures with insulation, foam, or other
material that will prevent convection or conduction cooling.

 Unless individual product specifications deem otherwise: Do not exceed fixtures maximum ambient

temperature.

 Only use fixture in its intended location.
 LED products are Polarity Sensitive. Ensure proper Polarity before installation.
 Electrostatic Discharge (ESD): ESD can damage LED fixtures. Personal grounding equipment must be

worn during all installation or servicing of the unit.

 Do not touch individual electrical components as this can cause ESD, shorten lamp life, or alter

performance.

 Some components inside the fixture may not be serviceable. In the unlikely event your unit may require

service, stop using the unit immediately and contact an ABL representative for assistance.

 Always read the fixtures complete installation instructions prior to installation for any additional fixture

specific warnings.

Conditions, please visit www.acuitybrands.com.

ABL LED General Warnings, Form No. 503.203

LED IMPORTANT SAFETY INSTRUCTIONS

statements.

© 2013 Acuity Brands Lighting, Inc. All rights reserved. 6/12/13

IM-365-A