Holmes HS4600 User Manual

HS4600

Page1

™

Ceramic

TER

OWNER’S GUIDE

PLEASE READ AND SAVE THESE INSTRUCTIONS

PLEASE READ AND SAVE THESE

IMPORTANT SAFEGUARDS

When using electrical appliances, basic precautions should always be taken to reduce the risk of fire, electric shock, and injury to persons, including the following:

1. Read all instructions before using the appliance.

2. To avoid fire or shock hazard, plug the appliance directly into a 120V AC electrical outlet.

3. The heater is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. If provided, use handles when moving this heater. Keep combustible materials, such as furniture, pillows, bedding, papers, clothes, and curtains at least 3 ft (0.9 m) from the front of the heater and keep them away from the sides and rear.

4. DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners, or the like. Arrange cord away from traffic area and where it will not be tripped over.

5. This heater is not intended for use in bathrooms, laundry areas and similar indoor location. NEVER locate heater where it may fall into a bathtub or other water container.

6. Extreme caution is necessary when any heater is used by, or near children or invalids, and whenever the heater is left operating and unattended.

7. Always unplug the heater when not in use.

8. When unplugging, be sure to pull by the plug and not the cord.

9. DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire, or damage the heater.

10.DO NOT operate heater with a damaged cord or plug, or after the heater malfunctions, has been dropped or damaged in any manner. Return appliance to manufacturer for examination, electrical or mechanical adjustment, or repair.

11. A heater has hot and arcing or sparking parts inside. DO NOT use it in areas where gasoline, paint, or flammable liquids are used or stored.

12.Use appliance only for intended household use as described in this manual. Any other use not recommended by the manufacturer may cause fire, electric shock, or injury to persons. The use of attachments not recommended or sold by The Holmes Group may cause hazards.

13. DO NOT use outdoors.

14.To prevent a possible fire, DO NOT block air intakes or exhaust in any manner. DO NOT use on soft surfaces, like a bed, where openings may become blocked.

15.To disconnect heater, turn controls to OFF, then remove plug from outlet.

16.Avoid the use of an extension cord because the extension cord may overheat and cause a risk of fire. However, if you have to use an extension cord, the cord shall be No. 14 AWG minimum size and rated not less than 1875 watts.

17.If the heater will not operate, see specific instructions on Auto Safety Shut-off.

18.DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void your warranty. The inside of the unit contains no user serviceable parts. All servicing should be performed by qualified personnel only.

Thank you for choosing a Holmes heater. To ensure the best performance from your heater, please read and save the

following instructions.

PLEASE READ AND SAVE THESE

IMPORTANT INSTRUCTIONS

AUTO SAFETY SHUT-OFF WITH CERAMIC CONTROL:

This heater is equipped with a patented, technologically-advanced, ceramic controlled safety system that requires the user to reset the heater if there is a potential overheat situation. When a potential overheat temperature is reached, the system will automatically shut the heater off. It can only resume operation when the user resets the unit.

To Reset the Heater:

1. Turn the Control Setting to the OFF position.

2. Unplug the heater and wait 10 minutes for the unit to cool down.

3. After the 10 minutes, plug the unit in again and operate normally.RE-

OPERATG INSTRUCTIONS:

PRE-OPERATING INSTRUCTIONS:

1. Carefully remove your heater from the box (please save the carton for off-season storage). You will find the unit is packed in two pieces with the metal Base Tubing needing to be attached to the heater housing (along with the Tilt Adjustment Knob).

2. To install the base tubing, simply take the silver colored end of the Base Tube and insert into the open ended tube on the bottom of the heater’s front housing. Lastly, line up the screw hole on the Base Tube with the opening on the tubing attached to the heater’s housing and insert the Tilt Adjustment Knob. Make sure the heater is in an upright position and tighten the Tilt Adjustment Knob.

3. Make sure the unit is in the OFF position before plugging the heater into the outlet.

4. Place heater on firm level surface.

NOTE: Avoid overloading your circuit by not using other high wattage appliances in the same outlet. At 1500 Watts, this unit draws 12.5 Amps.

OPERATING INSTRUCTIONS:

1. For heater operation, please set the Thermostat all the way to HI. (See fig. #1 and #2)

2. Turn the Selector Control to desired heat setting (LOW for 1000W or HI for 1500W).

3. For fan-only operation, without any heat output, turn the Selector Control to the FAN setting.

NOTE: The Power Light will remain lit as long as the unit is plugged in .

THERMOSTAT INSTRUCTIONS:

Setting the Thermostat:

1. Before setting the thermostat, allow heater to operate and warm up the room. You need to set thermostat on HI to start heater (See fig. #1 and #2).

Page2 Page 3

+ 2 hidden pages