Holmes HASF2219 User Manual
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic safety precautions should always
be taken including the following:
• Use fan only for purposes described in the instruction manual.
• To protect against electrical shock do not immerse unit, plug or cord in
water or spray with liquids.
• Close supervision is necessary when any appliance is used by or near
children.
• Unplug from outlet when not in use, when moving fan from one location to another, before putting on or taking off parts, and before
cleaning.
• Avoid contact with moving parts.
• Do not operate in the presence of explosive and/or flammable fumes.
• Do not place fan or any parts near an open flame, cooking or other
heating appliance.
• Do not operate any appliance with a damaged cord, plug, after the
appliance malfunctions, or has been dropped/ damaged in any manner.
• The use of attachments not recommended or sold by the appliance
manufacturer may cause hazards.
• Do not use outdoors.
• Do not let the cord hang over the edge of a table, counter, or come in
contact with hot surfaces.
• To disconnect, grip plug and pull from wall outlet. Never yank on cord.
• Always use on a dry, level surface.
• Do not operate without fan grills properly in place.
• This product is intended for household use ONLY and not for commercial
or industrial applications.
PLEASE READ AND SAVE THESE INSTRUCTIONS
WARNING: To reduce the risk of fire or electrical shock, DO NOT
USE THIS FAN with any SOLID STATE Fan Speed Control Device
HASF-2219
THIS PRODUCT IS EQUIPPED WITH A POLARIZED A.C.
(Alternating Current) PLUG (a plug having one blade
wider than the other). This plug will fit into the power
outlet only one way. This is a safety feature. If you are
unable to insert the plug fully into the outlet, try reversing the plug. If the
plug should still fail to fit, contact an electrician to replace the obsolete outlet.
DO NOT DEFEAT THE SAFETY PURPOSE OF THIS POLARIZED PLUG
Owner’s Guide
PLEASE READ AND SAVE THESE INSTRUCTIONS
19"OSCILLATING
STAND FAN
ASSEMBLY INSTRUCTIONS:
Base Assembly:
You will need the base and four extension legs.
Push in the small tab on each extension and snap into base
Pole Assembly:
You will need the completed base and extension pole.
STEP 1: Remove the base collar from the base by turning counter-clockwise.
STEP 2: Take the extension pole, with the solid end down, and insert it into
the base. The hollow end of the pole (with the screw hole) will be
facing up.
STEP 3: Replace the base
collar over the
extension pole,
slide it down the
pole, and secure it
to the base by turning clockwise.
Fan Head Assembly:
You are now ready to assemble the fan head (See Figure #3)
Step 1: Position the rear grill over the motor shaft, making certain the 2
notches at the top and bottom of the rear grill fit over the 2
prongs on the motor housing. Please make sure the rear grill fits
securely against the motor housing.
Step 2: Secure the rear grill in its place using the rear grill mounting nut.
Turn this nut clockwise and tighten firmly.
Step 3: Slide the fan blade, with the hollowed interior of the blade facing
towards the rear grill firmly onto the motor shaft. Make sure the
shaft protrudes from the front of the blade.
Step 4: Secure fan blade onto the motor shaft by turning the blade cap in
a counter-clockwise direction until it is firmly in place.
Step 5: Prepare the front grill by simply snapping the circular front grill
logo plate in place.
Step 6: Center the front grill by aligning the Holmes logo so it is horizontal
and parallel to the floor. Then secure the front and rear grills
completely together by snapping into place. Lastly, tighten the
grill screw at the bottom of the rear grill.
A. LOGO PLATE (SNAP ON)
B. FRONT GRILL
C. BLADE CAP
D. FAN BLADE
E. REAR GRILL MOUNTING
NUT
F. PLASTIC BAND
G. GRILL SCREW
H. REAR GRILL
I. MOTOR SHAFT
J. GRILL MOUNT
K. SPEED CONTROL KNOB
L. OSCILLATION BAR
M. MOTOR HOUSING
N. TILT JOINT
O. TILT ADJUSTMENT KNOB
P. FAN POST SCREW
Q. BASE COLLAR
A
N
B
C
D
E
O
F
G
H
I
M
J
K
L
(fig 4)
P
Q
Base
Collar
Extension
Pole
Base
Figure 1
Figure 2
Figure 3
Loading...