Holmes HASF1733, HASF1933, HASF1333 User Manual
HASF1333
HASF1733
HASF1933
®
Owner ’s Guide
Oscillating
Stand Fan
PLEASE READ AND SAVE THESE IMPORTANT INSTRUCTIONS
PLEASE READ AND SAVE
THESE IMPORTANT SAFETY
INSTRUCTIONS
When using electrical appliances, basic safety precautions should always be
followed to reduce the risk of fire, electric shock, and injury to persons,
including the following:
1) Read all instructions before using the appliance.
2) To avoid fire or shock hazard, plug the appliance directly into a 120V
AC electrical outlet.
3) Keep the cord out of heavy traffic areas. DO NOT let the cord hang
over the edge of a table or counter. To avoid fire hazard, NEVER
put the cord under rugs, near heat registers, radiator, stoves, or
heaters.
4) To protect against electrical hazards, DO NOT immerse in water or
other liquids. Do not use near water.
5) Close supervision is necessary when any appliance is used by or
near children, or by disabled people.
6) Always unplug the fan before moving it, putting on or taking off
parts, cleaning, or whenever the fan is not in use. Be sure to pull
by the plug and not the cord.
7) Avoid contact with moving parts. DO NOT operate without fan grills
properly in place.
8) DO NOT operate any appliance with a damaged cord or plug, if
motor fan fails to rotate, after the appliance malfunctions, or if it has
been dropped or damaged in any manner. Return appliance to manufacturer for examination, electrical or mechanical adjustment, or
repair.
9) DO NOT operate in the presence of explosive and/or flammable
fumes.
10) Use appliance only for intended household use as described in this
manual. Any other use not recommended by the manufacturer
may cause fire, electric shock, or injury to persons. The use of
attachments not recommended or sold by The Holmes Group may
cause hazards.
11) DO NOT use outdoors.
12) Always use on a dry, level surface.
13) Keep unit away from heated surfaces and open flames.
14) WARNING: To reduce the risk of fire or electric shock,DO NOT use
this fan with any solid-state speed control device.
THIS PRODUCT IS EQUIPPED WITH A POLARIZED AC
(Alternating Current) PLUG (a plug having one blade
wider than the other). This plug will fit into the power
outlet only one way. If the plug does not fit fully into the
outlet, reverse the plug. If it still does not fit, contact
qualified personnel to install the proper outlet.
DO NOT DEFEAT THE SAFETY PURPOSE OF THIS
POLARIZED PLUG IN ANY WAY
15) DO NOT attempt to repair or adjust any electrical or mechanical
functions on this unit. Doing so will void your warranty. The inside
of the unit contains no user serviceable parts. All servicing should be
performed by qualified personnel only.
PLEASE READ AND SAVE
THESE IMPORTANT SAFETY
INSTRUCTIONS
ASSEMBLY INSTRUCTIONS
Base / Pole Assembly
Step 1: Push in the small tab on each foot extension and snap into the
stand lock.
Step 2: Insert the hollow end of the lower pole into the stand lock until
it won’t go any further.
Step 3: Loosen up the adjustable height nut, raise the extension pole,
and tighten the nut.
Step 4: Loosen the upper pole nut. Firmly push the upper pole on to
the extension pole and tighten the upper pole nut.
Fan Head Assembly
Step 1: Position the rear grill over the motor shaft, making sure the
circular opening in the center of the rear grill fits over the
prongs on the rear housing. Please make sure the rear grill fits
securely against the motor housing.
Step 2: Secure the rear grill in its place using the rear grill-mounting
nut. Turn this nut clockwise and tighten firmly.
Step 3: Slide the fan blade, with the hollowed interior of the blade fac-
ing towards the rear of the grill firmly onto the motor shaft,
until the shaft protrudes from the front of the blade.
Step 4: Secure the fan blade onto the motor shaft by firmly tightening
the fan blade nut.
NOTE: TURN THE BLADE NUT COUNTER-CLOCKWISE
Step 5: Center the front grill by aligning the Holmes logo on the grill
hub so it is horizontal and parallel with the floor. Then, holding
the front grill against the rear grill, push the translucent grill
ring into place at the top and bottom of the fan. (Push directly
on the translucent grill ring, not on the grills them-selves.)
Finish securing the grill ring in the same manner until both
grills are joined underneath the translucent grill ring.
Step 6: Align the metal plate with the indentation on the bottom of the
grill ring. Pass the screw with the washer through the opening
on the bottom of the grill ring and fasten to the metal plate.
Loading...