Holmes HAP9243, HAP9415, HAP9423 User Manual

TROUBLESHOOTING

TROUBLESHOOTING

Problem Solution

• Unit will not operate.

• Decreased air flow.

• Excessive Noise.

LEARNING MORE

For a wealth of information about your air purifier and other Holmes® products, visit our website at
www.holmesproducts.com or call 1-800-546-5637.

4 Check if unit is properly plugged in and outlet is energized.
4 Make sure unit is turned ON.
4 Make sure filters are properly installed and front grill is seated correctly.

4 Make sure nothing is blocking air inlet and filtered air outlets.
4 Check condition of the filters and replace if necessary.
4 Check filters to remove any plastic wrapping/packaging.

4 Make sure parts are firmly positioned in place.
4 Open the air inlet grill, and make sure that any plastic packaging was

removed from the filters, if applicable.

AER1 FILTER SERIES

®

Congratulations! Your new air purifier is equipped with the new and improved
Aer1® Total Air Filter(s).

Filter Type Technology Consumer Benefit

THIS UNIT
COMES
WITH

© 2012 Sunbeam Products, Inc. doing business as Jarden Consumer Solutions. All Rights Reserved.
Distributed by Sunbeam Products, Inc. doing business as Jarden Consumer Solutions, Boca Raton, Florida 33431.

The ARM & HAMMER® name, logo and associated marks are trademarks of Church & Dwight Co., Inc. and are used
under license by Sunbeam Products, Inc.

160078 Rev. A HAP9243/HAP9415/HAP9423_12EM2 Printed In China
GCDS-HOL26622-ZZ

Total Air

Odor Eliminator

Allergen Remover

Allergen PerformancePlus

Smoke Grabber

99% HEPA-Type technology.

Infused with Arm & Hammer®

baking soda.

10 times the odor fighting power.

Contains Arm & Hammer® baking

soda, carbon and zeolite for odor

control.

99.97% True HEPA technology.

Removes up to 99.97% of particales

passing through the filter such as

pollen, dust, mold and dander.

99.99% True HEPA technology.
Helps remove up to 99.99% of par­ticles passing though the filter such

as pollen, dust, mold and dander.

HEPA-type filtration.

Triple layer protection specially

formulated with Arm & Hammer

Baking Soda, Carbon and Zeolite.
Remove up to 99% of smoke and

pollutants from the air stream.

®

Ideal for dust reduction.

Delivers 30% better air quality.

Ideal for eliminating odors from

pets, tobacco smoke and cooking

fumes.

Ideal for allergy sufferers.

Ideal for allergy sufferers.

Ideal for reducing smoke and odors

from smoke and VOC's.

WARRANTY INFORMATION

3 YEAR LIMITED WARRANTY

Sunbeam Products, Inc. doing business as Jarden Consumer Solutions or if in Canada, Sunbeam Corporation (Canada)
Limited doing business as Jarden Consumer Solutions (collectively “JCS”) warrants that for a period of three years
from the date of purchase, this product will be free from defects in material and workmanship. JCS, at its option, will
repair or replace this product or any component of the product found to be defective during the warranty period.
Replacement will be made with a new or remanufactured product or component. If the product is no longer available,
replacement may be made with a similar product of equal or greater value. This is your exclusive warranty. Do NOT
attempt to repair or adjust any electrical or mechanical functions on this product. Doing so will void this warranty.

This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable.
Keep the original sales receipt. Proof of purchase is required to obtain warranty performance. JCS dealers, service
centers, or retail stores selling JCS products do not have the right to alter, modify or any way change the terms and
conditions of this warranty.

This warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or
misuse of the product, use on improper voltage or current, use contrary to the operating instructions, disassembly, repair
or alteration by anyone other than JCS or an authorized JCS service center. Further, the warranty does not cover: Acts
of God, such as fire, flood, hurricanes and tornadoes.

What are the limits on JCS’s Liability?

JCS shall not be liable for any incidental or consequential damages caused by the breach of any express, implied or
statutory warranty or condition.

Except to the extent prohibited by applicable law, any implied warranty or condition of merchantability or fitness for a
particular purpose is limited in duration to the duration of the above warranty.

JCS disclaims all other warranties, conditions or representations, express, implied, statutory or otherwise.
JCS shall not be liable for any damages of any kind resulting from the purchase, use or misuse of, or inability to use

the product including incidental, special, consequential or similar damages or loss of profits, or for any breach of
contract, fundamental or otherwise, or for any claim brought against purchaser by any other party.

Some provinces, states or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or
limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights that vary from province to province,
state to state or jurisdiction to jurisdiction.

How to Obtain Warranty Service

In the U.S.A.
If you have any questions regarding this warranty or would like to obtain warranty service, please call

1-800-546-5637 and a convenient service center address will be provided to you.
In Canada
If you have any questions regarding this warranty or would like to obtain warranty service, please call

1-800-546-5637 and a convenient service center address will be provided to you.
In the U.S.A., this warranty is offered by Sunbeam Products, Inc. doing business as Jarden Consumer Solutions located

in Boca Raton, Florida 33431. In Canada, this warranty is offered by Sunbeam Corporation (Canada) Limited doing
business as Jarden Consumer Solutions, located at 20 B Hereford Street, Brampton, Ontario L6Y OM1. If you have any
other problem or claim in connection with this product, please write our Consumer Service Department. PLEASE DO

NOT RETURN THIS PRODUCT TO ANY OF THESE ADDRESSES OR TO THE PLACE OF PURCHASE.

Owner’s Guide

HAP9243, HAP9415, HAP9423

Aer1® Total Air Filter(s)

Air Purifier with Optional Ionizer

PLEASE READ AND SAVE THESE IMPORTANT INSTRUCTIONS

HAP9243_HAP9415_HAP9423-UA_12EM2.indd 1 10/15/12 9:25 AM

IMPORTANT SAFEGUARDS

FEATURES

FEATURES - OPERATIONS

CLEANING/MAINTENANCE

FILTER REPLACEMENT

When using electrical appliances, basic safety precautions
should always be followed to reduce the risk of fire, electric
shock, and injury to persons. These precautions include:

1. Read all instructions before using the appliance.

2. To avoid fire or shock hazard, plug the appliance
directly into a 120V AC electrical outlet.

3. If the Filter is covered by a bag when shipped,
remove plastic bag before use.

4. Keep the cord out of heavy traffic areas. To avoid
fire hazard, NEVER put the cord under rugs, near
heat registers, radiators, stoves, or heaters.

5. To protect against electrical hazards, DO NOT
immerse the appliance in water or other liquids. Do
not use near water.

6. Close supervision is necessary when any appliance is
used by or near children, or disabled persons.

7. Always unplug the air purifier before moving or
cleaning the unit, opening the grill, changing the
filter and whenever the unit is not in use. To
disconnect the unit, be sure to pull the plug and not
the cord.

8. NEVER drop or insert any objects into the openings of
the unit.

9. DO NOT operate any appliance with a damaged cord
or plug. If the motor fan fails to operate or the unit
has been dropped or damaged in any manner, return
appliance to manufacturer for examination and/or
repair.

10. Use appliance only for intended household use as
described in this manual. Any other use not
recommended by the manufacturer may cause fire,
electric shock, or injury to persons. The use of
attachments not recommended or sold by Jarden
Consumer Solutions may cause hazards.

THIS APPLIANCE HAS A POLARIZED PLUG (one blade is wider than the
other). To reduce the risk of electric shock, this plug is intended to fit in a
polarized outlet only one way. If the plug does not fit fully in the outlet,
reverse the plug. If it still does not fit, contact a qualified electrician to
install the proper outlet.

DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS

SAFETY FEATURE IN ANY WAY.

11. DO NOT use outdoors.

12. NEVER place on a soft surface such as a bed or sofa
as this could cause the unit to tip over and block the
air inlet or outlet grills.
Keep unit away from heated surfaces and open flames.

13.

14. DO NOT attempt to repair or adjust any electrical or
mechanical functions on this unit. Doing so will void
your warranty. The inside of the unit contains no user
serviceable parts. All servicing should be performed
by Jarden Consumer Solutions or an authorized
Jarden Consumer Solutions Center.

15. DO NOT place anything on top of unit.

16. NEVER use detergents, gasoline, glass purifier,
furniture polish, paint thinner, or other household
solvents to clean any part of the appliance.

17. Always turn the appliance off before unplugging it.

18.

The ionizer in this appliance produces less ozone than
the UL established limits of 50ppb (parts per billion).
However, in high concentrations, ozone can be harmful
to birds and small pets. To prevent ozone buildup, we
suggest using the ionizer in well ventilated areas with
the fan on.

19. This appliance should only be used in a room with
temperatures between 40° F and 110° F.

20. WARNING: To reduce the risk of fire or electric
shock, DO NOT use this appliance with any solid-state
speed control device.

PLEASE READ AND SAVE

THESE IMPORTANT

SAFETY INSTRUCTIONS

CORD SAFETY

• The length of cord used on this appliance was

selected to reduce tangling or tripping hazards.

• If a longer cord is necessary, an approved extension

cord may be used. The electrical rating of the
extension cord must be equal to or greater than the
electrical rating of the air purifier (see rating label
marked on bottom of the product).

• Care must be taken to arrange the extension cord so

that it will not drape over the countertop or tabletop
where it can be pulled on by children or accidentally
tripped over.

GET TO KNOW YOUR AIR PURIFIER

This unit is compatible with all Aer1® Filters. This allows
you to choose the filter that is just right for you. Below is
information on each filter:

TOTAL AIR - Advanced Dust Eliminating Technology
ODOR ELIMINATOR - 10x the odor fighting power
ALLERGEN REMOVER - 99.97% True HEPA technology

improves air quality for allergy sufferers
ALLERGEN PERFORMANCEPLUS - 99.99% True HEPA

technology improves air quality for allergy sufferers.
SMOKE GRABBER - 99% effective at removing smoke

from the air steam (*as small as 0.3 microns from air
passing through the filter)

IONIZER

This appliance has an optional ionizer feature which,
when turned on, releases negative ions into outgoing
filtered air to help the air purification process.

What Are Ions?

Ions are tiny particles that carry a positive or negative
charge. They exist naturally around us: in the air, water,
and ground. Both positive and negative ions are colorless,
odorless, and harmless.

How Does The Ionizer Work?

Negative ions help air purification by attaching
themselves to very small airborne particles in the room.
These particles take on a negative charge and may join
with positively charged particles such as dust, pollen,

smoke, and pet dander to form larger particles. These
larger particles are then more easily captured by the
filter system.

Important Notes:

Your ionizer may produce an occasional popping or
cracking sound. This is normal and occurs when a small
buildup of ions is discharged.

After extended use, you may notice dust around the grills
or front panel. This is caused by negative ions exiting the
air outlet, evidence of the ionizer’s air cleaning
effectiveness. You can remove the dust with a soft brush
or clean, damp cloth.

Larger particles may be attracted to positively charged
surfaces throughout the home, like walls or floors.

• This may occur more frequently when the filter is

nearing the end of its usable product life and is
unable to capture as many charged particles.

• Excessive amounts of pet dander, dust, or smoke may

decrease the life expectancy of the filter and

interfere with the ionization process.
To help prevent particles from attracting to surfaces
throughout your home:

• You may want to run the ionizer less often.

• Check the condition of the filter(s) more frequently.

CAUTION: The ionizer in this appliance produces less
ozone than the UL established limits of 50ppb. However,
in high concentrations, ozone can be harmful to birds and
small pets. To prevent ozone buildup, we suggest using
the ionizer in well ventilated areas with the air purifier
fan on.

HIGH, MEDIUM AND LOW SPEED
SETTINGS

For optimum air filtration, operate your Holmes® air
purifier continuously on the MEDIUM (2) setting. Its
rugged motor has been designed to give many years of
use. For quieter operation (such as in a bedroom), select
the LOW (1) setting. When high levels of air pollution are
present, select the HIGH (3) setting to quickly circulate
and filter the air in the room.

VISIPURETM FILTER REMINDER DIAL

Your Holmes® Air Purifier includes Aer1® Total-Air
Filter(s), specially designed to deliver cleaner air allowing
you to dust less often!! The Aer1® Total-Air filter(s) last 4
months. See back panel for other filter options.

The VisipureTM feature includes a magnifying glass which
allows you to get a magnified view of the dirt being
collected in the filter and see if the filter needs
replacement. The Filter Reminder Dial helps you keep
track of when to change the filter.

BEFORE USE

1. Carefully unpack your Air Purifier. Select a firm level
place where there are no obstructions to the air inlet
or filtered air outlet.

2. Remove the air inlet grill and check if the filter is
covered by a plastic bag. If it is, remove plastic bag
before use and place filters into unit. Reinstall the air
inlet grill.

3. This unit is equipped with a filter that lasts 4 months.
Please set the Filter Change Reminder to 4 months
from date of purchase. If you have a 12 month
filter, set the wheel from 12 months from date of
purchase. This will serve as a reference for when filter

replacement is needed.

NOTE: DO NOT POINT FILTERED AIR OUTLET TOWARDS WALL.

OPERATING INSTRUCTIONS

1. Plug into a 120V AC electrical outlet.

2. Select the desired operating speed; HI (3), MEDIUM
(2), LOW (1), by turning Speed Control Switch to the
appropriate setting. For optimum air filtration, it is
recommended to operate the air purifier continuously.
Its rugged motor has been designed to give many
years of use.

3. To release negative ions into the filtered air, press the
ionizer button ( ) to ON and the button will
illuminate in blue.

NOTE: The ionizer will not work unless the unit is

running.

Fig. 1

A

D

C

I

G

H

A. Control Panel
B. Speed Control

Switch

C. Visipure

D. Filter Reminder Dial

TM

Magnifying Glass

F

D

C

D

C

E. Ionizer Button
F. Filtered Air Outlet
G. Aer1® Filter(s)
H. Washable Foam

I. Air Inlet Grill

A

H

I

I

Pre-Filter

E

B

F

G

F

A

G

H

CLEANING/MAINTENANCE INSTRUCTIONS

1. Turn the air purifier off and unplug it before
cleaning.

2. The outside of the air purifier can be cleaned with a
soft, clean damp cloth.

3. The air inlet grill (reference Fig. 1) can be removed
and washed in warm soapy water (not dishwasher
safe). Dry before replacing in the unit.

4. The filtered air outlet can be cleaned of dust with a
small, soft brush.

5. If you wish to clean the inside filter chamber of the air
purifier, please only use a dry, soft cloth to wipe it down.

WARNING: Do not allow moisture to come in

contact with the main housing of the air purifier.

FILTER REPLACEMENT INSTRUCTIONS

IMPORTANT:

• DO NOT attempt to wash and re-use the Aer1® Filters.

• If the filters are enclosed in plastic bags, remove

them before use.

NOTE:

Every few weeks, check the condition of filter(s). The
VisipureTM feature includes a magnifying glass which
allows you to get a magnified view of the dirt being
collected in the filter. The Filter Reminder Dial also helps
you keep track of when to change the filters. Filter life
will vary, depending on air quality and usage (see
below). Under normal conditions of continuous use, the
Aer1 Total Air, Odor and Smoke Filters will last 4 months
while the Allergen and Allergen PerformancePlus Filters
will last 12 months.

After approximately 4 months of operation, check the
condition of the filter through the VisipureTM magnifying
glass and use Filter Reminder Dial to keep track on how
long a filter has been in use.

• Filters with a 4 month filter life: Wash the foam pre-

filter and replace the Aer1® filter(s) after 4 months
of operation.

• Filters with a 12 month filter life: After 4 months of

operation, it is recommended to wash the foam pre­filter and check the condition of your filter(s) through
the VisipureTM magnifying glass. The filters must be
replaced after 12 months of operation.

Filters can be purchased at a retailer near you, online at www.Aer1

Air Purifier

Model Number

HAP9243/HAP9415 1

HAP9423 2

Filter Quantity

Needed

To replace your filter(s):

1. Turn off and unplug the

2. Open the air inlet grill and

3. Remove the used Aer1

4. Install the new Aer1® filter(s) into the unit.This

5. Align the clip(s) on the side of Aer1® filter(s) with

6. Replace air inlet grill.

7. Turn the Filter Reminder Dial to select the current

Compatible with all
filter models below

HAPF30AT
HAPF30AO
HAPF30AS

HAPF300AH

HAPF300AP (D filter)

HAPF30 (A filter)

Fig. 2

air purifier.

examine the black foam
prefilter. Remove any dust
or lint and wash in warm
soapy water. Rinse, air dry
and place back into grill
inlet.

filter(s) from the unit by
pulling it gently towards
you and discard it. DO
NOT attempt to clean the
Aer1® filters.

model utilizes a hang tab and filter clip(s) to insure
that the filter(s) are properly in place. Before replacing
the filter(s), make sure that the hang tab is securely
in place. The clip(s) can only be attached to the tabs
on the filter(s) one way. The filter clip(s) should
easily slide onto the filter hang tab with only a small
amount of pressure. DO NOT use force while
attaching the clip to the filter. (Fig. 2)

rails on the inside of the purifier unit. Gently slide the
filter(s) onto the rail. (Fig. 3)

month you are replacing the new filter(s). This will
serve as reference for when filter replacement is
needed.

®

filters.com, or by calling (855) Try-Aer1®.

Aer1® Allergen PerformancePlus

Fig. 3

®

Filter

Description

®

Total Air Filter

Aer1

Aer1® Odor Filter

Aer1® Smoke Grabber Filter

Aer1® Allergen Remover Filter

"D" Filter

®

Holmes

"A" Filter

HAP9243_HAP9415_HAP9423-UA_12EM2.indd 2 10/15/12 9:25 AM