Holman TD30 Installation Manual

THERMAL VECTION

IL2263

Heat and Hold Drawer

MODEL

TVD30, TVD50

Installation and

Operation

Instructions

2M-Z14279 Rev. - 8/11/11

1

2

These symbols are intended to alert the user to the presence of
important operating and maintenance instructions in the manual
accompanying the appliance.

RETAIN THIS MANUAL FOR FUTURE REFERENCE

NOTICE

Using any part other than genuine Star factory supplied parts relieves the
manufacturer of all liability.

Star reserves the right to change specications and product design without

notice. Such revisions do not entitle the buyer to corresponding changes,
improvements, additions or replacements for previously purchased
equipment.

Due to periodic changes in designs, methods, procedures, policies and

regulations, the specications contained in this sheet are subject to change
without notice. While Star International Holdings Inc., Company exercises
good faith efforts to provide information that is accurate, we are not

responsible for errors or omissions in information provided or conclusions

reached as a result of using the specications. By using the information
provided, the user assumes all risks in connection with such use.

MAINTENANCE AND REPAIRS

Contact your local authorized service agent for service or required maintenance.
Please record the model number, serial number, voltage and purchase date in the area below and have it ready when

you call to ensure a faster service.

SAFETY SYMBOL

Model No.

Serial No.

Voltage

Purchase Date

Business

8:00 am to 4:30 p.m. Central Standard Time

Hours:

Telephone: [phone] Local [phone]

Fax: [phone] Local [phone]

E-mail [e-mail]

[e-mail]

[e-mail]

Website: www.star-mfg.com

Service Help Desk

Authorized Service Agent Listing

Reference the listing provided with the unit

or

for an updated listing go to:

Website: www.star-mfg.com
E-mail [e-mail]

Mailing Address: Star International Holdings Inc., Company

10 Sunnen Drive
St. Louis, MO 63143
U.S.A

2

Width

Depth

Height

IL2186

SPECIFICATIONS

Electrical Specications

Model Voltage Watts Amps Cord

TD30

TD50 1370 11.4A

TD30 24"

TD50 36"

120V

Dimensions

Width Depth Height

700 5.8A

29.75" 6.25"

NEMA 5-15P

CAUTION

WARNING

This equipment is designed and sold for commercial use only by personnel trained and experienced
in its operation and is not sold for consumer use in and around the home nor for use directly by the
general public in food service locations.

VOLTAGE

The thermal vection is equipped for use on the voltage specied on the nameplate.

DO NOT CONNECT TO ANY OTHER TYPE OF CURRENT OR THE MACHINE
WILL BE SERIOUSLY DAMAGED.

3

OPERATION

START-UP

When the unit is rst turned on it will begin the PRE-HEAT mode. The current hold temperature will
be displayed for 3 seconds, then “PHT” (PREHEAT) will ash along with the “HEAT ON” lamp until
the unit has reached its preset hold temperature. When this has been reached, the audible alarm will
beep 3 times, the “HEAT ON” lamp will stop ashing and the display will read “RDY”.

COOKING

Load the unit with the product, (thawed not frozen) Press the “COOK” button to begin. The “COOK”
light will remain on and the Temp light will be on as the unit call for heat. “COOK” will display for 3
seconds, and then the internal cook timer will begin counting down.

Close the drawer.

When the timer reaches 00:00, the audible alarm will beep 3 times.

Then you have two options:

1. Remove the product immediately from the Thermal Vection and place in on your preheated
roller grill for display, then press the “RESET” button. This will take the temperature back to the
PRE-HEAT mode temperature, until you are ready to cook again.

2. Leave the product in the Thermal Vection until you are ready to serve, the unit will maintain the
HOLD temperature and an internal timer will begin to count down, after 3 hours an audible alarm
will sound for 3 seconds and the display will ash “DoNE” until the RESET button is pressed. At

this time the remaining product left in the unit has expired and needs to be discarded.

READING TEMPERATURE

At any point the operator can view the actual temperature by pressing the “TEMP” button. The
reading will be displayed in the temperature mode (°F or °C) which is programmed.

PROGRAMMING THE TEMPERATURE MODE

The temperature mode can be changed from °F to °C or °C to °F by pressing and holding the “TEMP”
button while turning on the main power switch. The set-point temperature that is displayed will be in

the changed temperature mode.

PROGRAMMING HOLD / PREHEAT TEMPERATURE MODE ( F / C)

The HOLD / PREHEAT temperature and hold time can be programmed using the following steps.
The default HOLD temp and TIME are 140°F (60°C) for 3 hours.

1. Simultaneously press and hold the “TEMP” and “HOLD” buttons for approx 3 seconds.

2. The display will show “----“

3. Release the buttons.

4. Enter the 4 digit security code. (4,3,2,1)

5. Once completed, the current hold / preheat temperature will be displayed.

6. To increase or decrease the temperature use the “UP” or “DOWN” arrows.

7. Press the “TEMP” button to save the change.

8. The current time duration for the HOLD mode is now displayed.

9. Use the “UP” or “DOWN” arrows to increase or decrease the HOLD time.

10. Press the “TEMP” button to save the new HOLD time.

11. Press the “TEMP” button again to exit the programming mode.

4