Holman QCSE 2 600hw Installation Manual

Conveyor Toasters Installation Instructions

These symbols are intended to alert the
user to the presence of important operating
and maintenance instructions in the manual
accompanying the appliance.

Go to:

www.star-mfg.com/scripts/manuals.aspx

to obtain this units installation & operations

manual, warranty & other documents.

NOTICE

Using any part other than genuine Holman factory supplied parts
relieves the manufacturer of all liability.

Holman reserves the right to change specications and product

design without notice. Such revisions do not entitle the buyer to
corresponding changes, improvements, additions or replacements
for previously purchased equipment.

Due to periodic changes in designs, methods, procedures, policies

and regulations, the specications contained in this sheet are subject

to change without notice. While Holman Manufacturing exercises
good faith efforts to provide information that is accurate, we are
not responsible for errors or omissions in information provided

or conclusions reached as a result of using the specications.

By using the information provided, the user assumes all risks in
connection with such use.

CAUTION

This equipment is designed and sold for commercial use only by
personnel trained and experienced in its operation and is not sold
for consumer use in and around the home nor for use directly by
the general public in food service locations.

Before using your new equipment, read and understand all the
instructions & labels associated with the unit prior to putting it into
operation. Make sure all people associated with its use understand
the units operation & safety before they use the unit.

All shipping containers should be checked for freight damage both
visible and concealed. This unit has been tested and carefully
packaged to insure delivery of your unit in perfect condition.
If equipment is received in damaged condition, either apparent or
concealed, a claim must be made with the delivering carrier.

Concealed damage or loss - if damage or loss is not apparent until
after equipment is unpacked, a request for inspection of concealed
damage must be made with carrier within 15 days. Be certain to
retain all contents plus external and internal packaging materials
for inspection. The carrier will make an inspection and will supply
necessary claim forms.

GENERAL SAFETY INFORMATION

MODEL

QCSE-2-600HW

Conveyor Toasters

Electronic Controls

GENERAL INSTALLATION INFORMATION

The unit was shipped fully assembled and ready to plug into a

standard outlet specied for its voltage and amp draw. If improper
electrical supply is determined, contact a qualied electrician prior

to using the unit. Removal and replacement of the power cord
and plug will void the warranty. For assistance, contact your local
authorized service agent for service or required maintenance.

Level unit using the adjustable feet under the unit (approximately
1/2" adjustment).

Before using the unit for the rst time, wipe down the exterior with

a damp cloth.
Allow enough space around the toaster for adequate ventilation.

Do not operate the unit without the crumb tray properly positioned.
Overheating and poor toasting may occur. Read all labels on the
unit and follow their instructions.

MAINTENANCE AND REPAIRS

Contact the factory, a service representative or a local
service company for service or required maintenance.

Go to www.star-mfg.com/scripts/manuals.aspx to nd a service

agent near you. Replacement cord sets must be purchased from
Star Manufacturing International, Inc. or our authorized agents.

Should you need any assistance regarding the operation or
maintenance of any Holman equipment; write, phone, fax or
e-mail our service department. In all correspondence mention
the model number and the serial number of your unit, along with
the voltage.

Business Hours:
Telephone: [phone]
Fax: [phone]
E-mail: [e-mail]

[e-mail]
[e-mail]

Website: www.star-mfg.com
Mailing Address: Star International Holdings Inc., Company

10 Sunnen Drive
St. Louis, MO 63143
U.S.A.

8 am to 4:30 p.m. Central Standard Time

2M-Z13413, Rev. - 3/26/2010

ELECTRICAL CONNECTION

Before making any electrical connection to this unit,
check that the power supply is adequate for the voltage,
amperage and requirements stated on the rating plate.
A wiring diagram is included in the Installation & Operations

manual, which can be downloaded at

WARNING

Disconnect the unit from the power source before installing or
removing any parts.

Be absolutely sure that the ground connection for the receptacle is
properly wired. Do not connect equipment to power without proper
ground connections. Improper grounding may result in personal

injury or fatality.

www.star-mfg.com/scripts/manuals.
aspx.

DO NOT CUT OR REMOVE THIS PLUG OR GROUNDING
PRONG FROM THE PLUG.

CONNECT/PLUG UNIT INTO DEDICATED

WARNING

A.C. LINE ONLY SPECIFIED ON THE DATA
PLATE OF THE UNIT.

WARNING

CERTAIN SURFACES ARE EXTREMELY HOT
DURING OPERATION AND CARE SHOULD
BE TAKEN WHILE USING THIS UNIT.

CAUTION

DO NOT IMMERSE OR LET THE UNIT STAND
IN WATER.

DO NOT HOSE DOWN THE UNIT OR THE

WARNING

TABLE/COUNTER IF THE UNIT IS ON THE
TABLE/COUNTER.

KEEP AWAY FROM RUNNING WATER.

The Holman QCSe conveyor toaster
comes with pre-programmed factory
default settings for TST-1, TST-2, TST-3,
TST-4, TST-5, TST-6. The operator may
change these setting at any time.

Press 1 and TST-1 will appear
Press 2 and TST-2 will appear
Press 3 and TST-3 will appear
Press 4 and TST-4 will appear
Press 5 and TST-5 will appear
Press 6 and TST-6 will appear.
Factory default settings are as follow:

QCSE-2-600HW DEFAULT SETTINGS

Menu

Buttons

TST - 1

Top

Heat

Bottom

Heat

Conveyor

Speed

70

TST - 2 64
TST - 3 58
TST - 4 52

9 10

TST - 5 46
TST - 6 40

SAVER* 50% 50% OFF

POWER SAVER SWITCH
NOTE: This Power Saver Switch has been disabled from the

factory, it can be enabled through the programming procedures.
There are three Power Saver modes:

ON: Unit is in pre-programmed power saving setting.
OFF: Power Saver mode is turned off.
AUTO ON: Power Saver turns on when there has been no activity

for a programmed length of time.

The operator may adjust the level of power reduction for the saver
mode. (Note: conveyor may move slowly when in saver mode.)

Two buttons (+) and (-) are used when increasing or decreasing the

value of each programmable setting.
A red LED light located at the lower portion of the control panel label

will indicate if the value for top heat, bottom heat or conveyor speed

is being adjusted.