Holman QCS3 1400 Specifications

®

®

®

®

CONVEYOR TOASTER

MODEL

QCS-3-1400BH,

RCS-3-1400BH SERIES

Installation and

Operation

Instructions

2M-HG0659 Rev. D 11/13/2009

QCS-3-1400BH

SAFETY SYMBOL

These symbols are intended to alert the user to the presence of important operating and maintenance instructions in the manual accompanying the appliance.

RETAIN THIS MANUAL FOR FUTURE REFERENCE

NOTICE

Using any part other than genuine Star factory supplied parts relieves the manufacturer of all liability.

Star reserves the right to change specifi cations and product design without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment.

Due to periodic changes in designs, methods, procedures, policies and regulations, the specifi cations contained in this sheet are subject to change without notice. While Star Manufacturing exercises good faith efforts to provide information that is accurate, we are not responsible for errors or omissions in information provided or conclusions reached as a result of using the specifi cations. By using the information provided, the user assumes all risks in connection with such use.

MAINTENANCE AND REPAIRS

Contact your local authorized service agent for service or required maintenance. Please record the model number, serial number, voltage and purchase date in the area below and have it ready when you call to

ensure faster service.

Model No.

Serial No.

Voltage

Purchase Date

Authorized Service Agent

Reference the listing provided with the unit or

for an updated listing go to:

Website:	www.star-mfg.com
E-mail	[e-mail]
Telephone:	[phone] Local [phone]

The Star Service Help Desk

Business	8:00 am to 4:30 p.m. Central Standard Time
Hours:
Telephone:	[phone]	Local [phone]
Fax:	[phone]	Local [phone]
E-mail	[e-mail]
	[e-mail]
	[e-mail]
Website:	www.star-mfg.com

Mailing Address: Star Manufacturing International Inc.

10 Sunnen Drive

St. Louis, MO 63143

U.S.A

2

GENERAL INSTALLATION DATA

CAUTION

This equipment is designed and sold for commercial use only by personnel trained and experienced in its operation and is not sold for consumer use in and around the home nor for use directly by the general public in food service locations.

Before using your new equipment, read and understand all the instructions & labels associated with the unit prior to putting it into operation. Make sure all people associated with its use understand the units operation & safety before they use the unit.

All shipping containers should be checked for freight damage both visible and concealed. This unit has been tested and carefully packaged to insure delivery of your unit in perfect condition. If equipment is received in damaged condition, either apparent or concealed, a claim must be made with the delivering carrier.

Concealed damage or loss - if damage or loss is not apparent until after equipment is unpacked, a request for inspection of concealed damage must be made with carrier within 15 days. Be certain to retain all contents plus external and internal packaging materials for inspection. The carrier will make an inspection and will supply necessary claim forms.

INSPECTION & ASSEMBLY

UNCRATING AND INSPECTING

Unpack the unit and components from the shipping container. Remove all visible packing material and those from inside the cooking chamber. If damage is discovered, file a claim immediately with the carrier that handled the shipment. Do not operate the unit if it was

damaged during shipping.

ASSEMBLY AND INSTALLATION

The unit was shipped fully assembled and ready to plug into a standard outlet specified for its voltage and amp draw. If improper electrical supply is determined, contact a qualified electrician prior to using the unit. Removal and replacement of the power cord and plug will void the warranty. For assistance, contact your local authorized service agent for service or required maintenance.

Level unit using the adjustable feet under the unit (approximately 1/2" adjustment).

Before using the unit for the first time, wipe down the exterior with a damp cloth.

CAUTION

Allow enough space around the toaster for adequate ventilation. Do not operate the unit without the crumb tray properly positioned. Overheating and poor toasting may occur. Read all labels on the unit and follow their instructions.

ELECTRICAL CONNECTION

WARNING

Before making any electrical connection to this unit, check that the power supply is adequate for the voltage, amperage and requirements stated on the rating plate. A wiring diagram is included herewith.

Disconnect the unit from the power source before installing or removing any parts.

Be absolutely sure that the ground connection for the receptacle is properly wired. Do not connect equipment to power without proper ground connections. Improper grounding may result in personal injury or fatality.

WARNING

DO NOT CUT OR REMOVE THIS PLUG OR GROUNDING PRONG FROM THE PLUG.

WARNING

CONNECT/PLUG UNIT INTO DEDICATED A.C. LINE ONLY SPECIFIED ON THE DATA PLATE OF THE UNIT.

DAILY OPERATION

ROTARY POWER SAVER SWITCH

For toasters equipped with a Rotary Power Saver Switch, turn clockwise or counterclockwise to get in the following positions.

FULL POWER

When in this position your equipment is at full power and ready to use.

OFF ROTARY

Two off positions are provided, a single rotation to either direction will shut the unit off.

STANDBY

The standby position reduces the power consumption by 75%. Using this position during the quiet times will save electricity, and keep the toaster warm. When needed, turn the switch to FULL POWER. Recovery time is about 30 seconds.

CAUTION

	CERTAIN SURFACES ARE EXTREMELY HOT DURING OPERATION AND CARE
	SHOULD BE TAKEN WHILE USING THIS UNIT.
		BUN MODE
	COOKING PROCEDURES
		TOP HEAT
	This toaster is equipped with a swinging heat shutter at the oven		ONLY
	entrance. This shutter will move out of the way as the product passes
	under it.
	TOAST/BUN MODE SWITCH
	This model is also equipped with a Toast/Bun mode switch. Place the
	switch in Bun Mode to initiate the 4 heater tubes on the top, turning
	off the bottom 2 tubes. Place the switch in the toast mode to turn on
	all 2 top and 2 bottom heater tubes.
	BREAD/BUN TOASTING
	1) Turn the power saver to FULL POWER.	TOAST MODE
	2) Set the conveyor speed to HIGH.	TOP & BOTTOM
			HEAT

3)Set top and bottom heat controls at HIGH.

4)Set the Toast/Bun mode switch in the desired position (See figure this page) depending on what you are toasting.

5)Allow warm up time of up to 10 minutes.

6)Place a sample product on the conveyor belt to test the settings.

•If toasting is too light, turn conveyor speed control counterclockwise to a slower speed.

•If toasting is too dark, turn heat controls to a lower heat.

(NOTE: Some products may require adjustment of the top and bottom heat controls in order to achieve the desired results. Results may vary from the day to day operation

depending on amount of moisture in the bread.)

TOASTER COMPONENTS
		FRONT
LOAD UP
CRUMB TRAY	SPEED CONTROL
	HEAT CONTROLS	HIGH LIMIT RESET
BUN / TOAST		AIR INTAKE FAN
SWITCH
	POWER SAVER SWITCH	POWER CORD

DAILY OPERATION

Check the power cord to insure that it is plugged into a proper outlet. Set the heat control knobs to desired temperature.

Always allow up to 10 minutes of preheat time before loading the unit with product. Failure to allow sufficient preheat time will result in unsatisfactory cooking until the unit reaches

operating temperature.

OPERATING HINTS AND SAFETY

Disconnect power to the unit with the switch at the end of each day of operation.

Never operate the unit without the crumb tray installed, the unit will overheat and activate the HEAT LIMIT SWITCH.

Do not leave the unit in operation without an attendant.

Turn Power Saver Switch to Standby during idle	OPERATE
periods. It will take only a few minutes to regain
operating temperature.

Do not leave the unit at high temperature when not in use or during idle periods. This will cause food particles and grease film to carbonize.

CLEAN

CLEANING
	Crumb Tray Removal & Installation

Preventive maintenance for your Holman toaster consists of the following recommended cleaning procedures. To keep your toaster in its top operating condition, these steps should be performed on a daily or weekly as indicated.

A.Turn main power saver switch to the OFF position. Disconnect unit from power source.

B.After the unit cools, remove interior crumb tray (as shown on previous page) and clean. Slide crumb tray back into position.

C.Wipe exterior surface of unit.

D.Clean air intake on bottom of unit.

E.For lightly soiled conveyor belts, turn conveyor speed control to fastest setting (100) and wipe with a damp cloth (daily) For heavily soiled conveyors, turn conveyor speed control to fastest setting and wipe with a light abrasive pad (as needed). Then empty crumb tray.