Holman Q3ARB Specifications

®

®

®

®

®

CONVEYOR

TOASTER

MODEL

Q3-95ARB

Installation and

Operation

Instructions

2M-Z10141 Rev. F 7/09/2010

9H-Q3-95ARB

1

2

These symbols are intended to alert the user to the presence of
important operating and maintenance instructions in the manual
accompanying the appliance.

RETAIN THIS MANUAL FOR FUTURE REFERENCE

NOTICE

Using any part other than genuine Star factory supplied parts relieves the
manufacturer of all liability.

Star reserves the right to change specications and product design without

notice. Such revisions do not entitle the buyer to corresponding changes,
improvements, additions or replacements for previously purchased
equipment.

Due to periodic changes in designs, methods, procedures, policies and

regulations, the specications contained in this sheet are subject to change
without notice. While Star International Holdings Inc., Company exercises
good faith efforts to provide information that is accurate, we are not

responsible for errors or omissions in information provided or conclusions

reached as a result of using the specications. By using the information
provided, the user assumes all risks in connection with such use.

MAINTENANCE AND REPAIRS

Contact your local authorized service agent for service or required maintenance.
Please record the model number, serial number, voltage and purchase date in the area below and have it ready when

you call to ensure a faster service.

SAFETY SYMBOL

Model No.

Serial No.

Voltage

Purchase Date

Business

8:00 am to 4:30 p.m. Central Standard Time

Hours:
Telephone: [phone] Local [phone]
Fax: [phone] Local [phone]

E-mail [e-mail]

[e-mail]

[e-mail]

Website: www.star-mfg.com

Service Help Desk

Authorized Service Agent Listing

Reference the listing provided with the unit

or
for an updated listing go to:

Website: www.star-mfg.com
E-mail [e-mail]
Telephone: [phone] Local [phone]

Mailing Address: Star International Holdings Inc., Company

10 Sunnen Drive
St. Louis, MO 63143
U.S.A

2

SPECIFICATIONS

Q3-95ARB-V02

Rating/Connection: 4200 Watts (700W elements), 20.5 Amps at 208V

NEMA 6-30P plus with six foot oil-resistant cord

Electrical Supply: 208VAC, single phase
Approximate Weight: Installed - 60 Lbs (27.22 kg)

Shipping - 68 Lbs (30.84 kg)
Dimensions: Width: 18.5" (47.0 cm)

Depth: 22.4 (56.8 cm)
Height: 15.7" (39.7 cm)

Q3-95ARB-V04

Rating/Connection: 4200 Watts (700W elements), 17.5 Amps at 240V

NEMA 6-30P plus with six foot oil-resistant cord

Electrical Supply: 240VAC, single phase
Approximate Weight: Installed - 60 Lbs (27.22 kg)

Shipping - 68 Lbs (30.84 kg)
Dimensions: Width: 18.5" (47.0 cm)

Depth: 22.4 (56.8 cm)
Height: 15.7" (39.7 cm)

The below models were released in May 2008, nearly identical to the previous units listed above.
All changes are internal and both units operate and work the same.

Q3-95ARB-208V

Rating/Connection: 4200 Watts (700W elements), 20.5 Amps at 208V

NEMA 6-30P plus with six foot oil-resistant cord

Electrical Supply: 208VAC, single phase
Approximate Weight: Installed - 60 Lbs (27.22 kg)

Shipping - 68 Lbs (30.84 kg)
Dimensions: Width: 18.5" (47.0 cm)

Depth: 22.4 (56.8 cm)
Height: 15.7" (39.7 cm)

Q3-95ARB-240V

Rating/Connection: 4200 Watts (700W elements), 17.5 Amps at 240V

NEMA 6-30P plus with six foot oil-resistant cord

Electrical Supply: 240VAC, single phase
Approximate Weight: Installed - 60 Lbs (27.22 kg)

Shipping - 68 Lbs (30.84 kg)
Dimensions: Width: 18.5" (47.0 cm)

Depth: 22.4 (56.8 cm)
Height: 15.7" (39.7 cm)

3

CAUTION

General Information

This equipment is designed and sold for commercial use only by personnel trained and

experienced in its operation and is not sold for consumer use in and around the home nor
for use directly by the general public in food service locations.

Before using your new equipment, read and understand all the instructions & labels
associated with the unit prior to putting it into operation. Make sure all people associated
with its use understand the units operation & safety before they use the unit.

INSPECTION

UN-CRATING AND INSPECTING

Unpack the unit and components from the shipping container. Remove all visible packing

material and those from inside the cooking chamber. If damage is discovered, le a claim

immediately with the carrier that handled the shipment. Do not operate the unit if it was
damaged during shipping. All shipping containers should be checked for freight damage
both visible and concealed. This unit has been tested and carefully packaged to insure
delivery of your unit in perfect condition. If equipment is received in damaged condition,
either apparent or concealed, a claim must be made with the delivering carrier.

Concealed damage or loss - if damage or loss is not apparent until after equipment is
unpacked, a request for inspection of concealed damage must be made with carrier within
15 days. Be certain to retain all contents plus external and internal packaging materials for
inspection. The carrier will make an inspection and will supply necessary claim forms.

ELECTRICAL CONNECTION

Disconnect the unit from the power source before installing or removing any parts.
Be absolutely sure that the ground connection for the receptacle is properly wired.

Do not connect equipment to power without proper ground connections. Improper
grounding may result in personal injury or death.

CAUTION

Allow enough space around the toaster for adequate ventilation. Do not operate the unit

without the crumb tray properly positioned. Overheating and poor toasting may occur.
Read all labels on the unit and follow their instructions.

WARNING

Before making any electrical connection to this unit, check that the power

supply is adequate for the voltage, amperage and requirements stated on the
rating plate. A wiring diagram is included.

WARNING

DO NOT CUT OR REMOVE THIS PLUG OR THE GROUNDING PRONG FROM

THE PLUG. FAILURE TO COMPLY MAY RESULT IN DEATH OR SERIOUS
INJURY.

WARNING

CONNECT/PLUG UNIT INTO DEDICATED A. C. LINE ONLY SPECIFIED ON THE

DATA PLATE OF THE UNIT.

CAUTION

SOME SURFACES ARE EXTREMELY HOT DURING OPERATION AND CARE SHOULD

BE TAKEN WHILE USING THIS UNIT.

4

ASSEMBLY AND INSTALLATION

The unit was shipped fully assembled and ready to plug into a standard outlet specied for
its voltage and amp draw. If improper electrical supply is determined, contact a qualied

electrician prior to using the unit. Removal and replacement of the power cord and plug
voids the warranty. For assistance, contact your local authorized service agent for service
or required maintenance.

Level unit using the adjustable feet under the unit (approximately 1/2" adjustment).
Wipe down the exterior with a damp cloth.

NOTE

The security cover prevents accidental movement of the speed control knob during routine
operations.

TOASTER SETTINGS

Before using the unit for the rst time, test the pass time of the conveyor belt.
The pass time through the toaster should be between 30 and 40 seconds.

1. Turn the conveyor speed knob to the 12 o'clock position.

2. Set both heat controls to HIGH and allow to 5 to 10 minutes to reach operating
temperature.

3. Place a bun on the conveyor belt.

4. Start timer, when the bun begins enters the cooking chamber

5. Stop timer when bun exits the toaster.

IF TO DARK: Increase conveyor speed knob.

TO LIGHT: Decrease conveyor speed knob.

IF

6. When the bun meets all specications, mark the control panel face with a marking tool

where the control knob was set.

7. Place the security device over the control knobs and secure.

8. If the bun takes longer than 40 seconds, then contact Arby's Corporation to be certain

you understand the specications. If the unit still does not toast the bun in 40 seconds,

or less then contact Star Manufacturing.

DAILY OPERATION

Rotary Power Saver Switch

Turn Power Saver Switch clockwise or counterclockwise for the following settings.

Full Power

When in this position your equipment is at full power and ready to use.

Off Rotary

Two off positions are provided, a single rotation in either direction will shut the unit off.

Standby

The standby position reduces the power consumption by 75%. Using this position during

the quiet times will save electricity, and keep the toaster warm. When needed, turn the
switch to FULL POWER. Recovery time is about 30 seconds.

5

Toasting Procedures

CRUMB TRAY

POWER SAVER
LOCKING COVER

RECEPTACLE

HEAT CONTROLS

SPEED CONTROL

FRONT

AIR INTAKE FAN

HIGH LIMIT RESET

POWER CORD

IL1244

FASTENER

HEAT SHUTTER

This toaster is equipped with a swinging heat shutter at the toaster entrance. This shutter will

move out of the way as the product passes under it.

1) Turn the power saver to FULL POWER.

2) Allow warm up time of 5 to 10 minutes.

3) Place a product on the conveyor belt.

Toaster Components

OPERATING HINTS AND SAFETY

Disconnect power to the unit with the switch at the end of each day of operation.
Do not leave the unit in operation without an attendant.
Turn Power Saver Switch to Standby during idle periods. It will take only a few minutes to

regain operating temperature.
Do not leave the unit at high temperature when not in use or during idle periods. This will

cause food particles and grease lm to carbonize.

6

OPERATE

IL1243

CLEAN

FRONT

AIR INTAKE FAN

CLEANING

Preventive maintenance for your Holman toaster consists of the following recommended

cleaning procedures. To keep your toaster in top operating condition, these steps should be
performed daily or weekly as indicated.

1. Wipe exterior surface of unit, using mild detergent and water.

2. For lightly soiled conveyor belts, turn conveyor speed control to highest setting and wipe

with a damp cloth.

For heavily soiled conveyors, turn conveyor speed control to highest setting and wipe with

3.

a light abrasive pad (as needed).

4. T

urn main power saver switch to the OFF position.

5. Disconnect unit from power source.

6. After the unit cools, remove interior crumb tray (as shown below) and clean.

Slide crumb tray back into position. Never operate unit without Crumb Tray properly
installed.

7. Clean air intake on bottom of unit on a weekly basis.

WARNING

DO NOT IMMERSE OR LET THE UNIT STAND IN WATER. DO NOT HOSE DOWN
THE UNIT OR THE TABLE/COUNTER IF THE UNIT IS ON THE TABLE/COUNTER.

KEEP AWAY FROM RUNNING WATER.

Crumb Tray & Air Intake Cleaning

7

Troubleshooting Guide

A. Unit Will Not Heat, Conveyor Belt Will Not Move.

1) Be sure the main circuit breaker is switched to the ON position.

2) Check to see if the toaster is plugged in and all controls are turned to the ON position.

B. Unit Has Heat Only On One Side, Conveyor Belt Turns Freely.

1) Call the Star Service Help Desk at 1-800-807-9054, as heating element may need replacing.

C. Conveyor Will Not Turn, Unit Heats Properly.

To check for mechanical binding:

1) DISCONNECT UNIT FROM POWER SOURCE.

2) Remove 2 screws holding enclosure to the bottom of the unit.

3) Set unit on the legs and remove 4 screws on the back of the toaster.

4) Slide the enclosure off the unit and remove the back panel.

5) Loosen the four screws that hold the drive motor in place.

6) Slide the motor up allowing the drive chain to be removed from the sprockets.

7) Move the conveyor belt by hand to check for mechanical binding. If conveyor moves freely,
call the Star Service Help Desk at 1-800-807-9054, as the drive motor and/or speed control
may need replacing.

8) Replace the enclosure by sliding it forward towards the front of the unit.
The front edge of the enclosure will slide beneath the toaster front.

D. Heat Limit Switch (Reset)

Your Holman conveyor toaster is equipped with an automatically activated heat limit switch that
interrupts the heater tube connections if the ambient temperature in the control box exceeds
190°F (88°C). This switch can be reset manually by pushing the red button located on the back of
the unit as shown in the Toaster Components Illustration on Page 6.

1) DISCONNECT UNIT FROM POWER SOURCE.

2) Check to see if air intake area in the bottom center of the control box cover is free of dust,
grease or other obstructions.

3) Check if crumb tray is in place. OPERATING THE UNIT WITHOUT THE CRUMB TRAY IN
PLACE WILL CAUSE OVERHEATING IN THE CONTROL BOX.

4) If no obstructions to the airow can be found and if the crumb tray is in place,
call the Star Service Help Desk at 1-800-807-9054 for assistance.

E. Conveyor Turns At One Speed Regardless Of Speed Control Setting.

1) Call the Star Service Help Desk at 1-800-807-9054, as speed control should be replaced.

F. Product Sticking To Conveyor Or Slide

Your Holman conveyor toaster is designed to toast product that is current room temperature.
DO NOT attempt to put frozen, refrigerated, or any butter or a butter substitute material in the
toaster. Doing so may cause it to come out doughy or very moist, as well as possibly sticking to
parts of the unit.
Follow the cleaning procedures listed on page 7.

8

Maintenance Procedures

1/4”

A. Replacing the Heater Tubes

1) DISCONNECT UNIT FROM POWER SOURCE.

2) Remove the enclosure.

3) Remove heater tube wire from terminal block connection, keeping top and
bottom wires separate.

4) Lift heater tube retainers by loosening retaining screws and sliding the retainer plate up.
Hand tighten the plate to hold it up so the heater tubes will slide out freely.

5) Gently, pull defective heater tube out of unit.

6) Gently, put new heater tube into unit.

7) Loosen retainer screws and slide the retainer back into place. Tighten the screw to
secure the retainer in place over the ends of the heater tubes.

B. Replacing the Fan Motor

1) DISCONNECT UNIT FROM POWER SOURCE.

2) Remove screws from the enclosure and the back panel at rear of unit.

3) Remove the enclosure and the back panel.

4) Unplug power supply cord from fan motor.

5) Remove (4) screws, which hold fan motor and grill to bottom of unit and remove fan.

6) Put replacement motor and grill in place and secure to the bottom of unit with screws.

7) Reconnect power supply cord to fan motor.

8) Replace back panel and enclosure. Fasten with screws removed in step 2.

C. Replacing the Belt Drive Motor

1) DISCONNECT UNIT FROM POWER SOURCE.

2) Remove enclosure and back panel.

3) Remove sprocket from motor shaft, using an allen wrench and loosening the set-screw.

4) Remove the wire from terminal block connecting the drive motor to internal wiring.
On units rated 208 or 240 volts, note which color leads are being used for these connections
and which lead is capped with white tape. The new motor should use the same arrangement.

5) Remove screws holding motor in place and remove motor from unit.

6) Put new motor in place and attach loosely with mounting screws.

7) Replace sprocket on motor shaft.

NOTE The two sprockets should line up parallel with each other, so the chain does not twist
any during operation. Also the hub gets installed closets to the motor.

8) Slide motor until the drive chain has about 1/4” slack when lightly pushed at the center of its top
open run. See chain tensioning illustration.

9) Tighten screws to secure motor.

10) Rewire leads same as removed in step 4.

11) Replace side panel and control box cover.

D. Clean the Air Intake (Once A Week)

1) DISCONNECT UNIT FROM POWER SOURCE.

2) Place unit on its backside.

3) Use a vacuum cleaner and or a damp cloth to clean
the air intake.

E. Lubricate the Chain & Sprockets (Every 6 Months)

1) DISCONNECT UNIT FROM POWER SOURCE.

2) Remove enclosure exposing chain drive.

3) While wearing rubber gloves and using an extreme pressure,
synthetic chain lubricant with a temperature range up to
400°F (204°C) lubricate chain and sprockets. Apply liberally.
This grease is available as part no. 1P-Z8914.

4) Replace enclosure, Reconnect power source and test unit.

9

Chain Tension

2M-4497-2 10/2010

The foregoing warranty is in lieu of any and all other warranties expressed or implied and constitutes the entire warranty.

FOR ASSISTANCE

Should you need any assistance regarding the Operation or Maintenance of any Star equipment; write, phone, fax or email our Service Department.

In all correspondence mention the Model number and the Serial number of your unit, and the voltage or type of gas you are using.

ALL:
* Pop-Up Toasters
* Butter Dispensers
* Pretzel Merchandisers

(Model 16PD-A Only)

* Pastry Display Cabinets
* Nacho Chip Merchandisers
* Accessories of any kind
* Sneeze Guards
* Pizza Ovens

(Model PO12 Only)

* Heat Lamps
* Pumps-Manual

Visit our Website at: www.star-mfg.com Email: [e-mail]

THOROUGHLY INSPECT YOUR UNIT ON ARRIVAL

This unit has been tested for proper operation before leaving our plant to insure delivery of your unit in perfect condition. However, there are instances in
which the unit may be damaged in transit. In the event you discover any type of damage to your product upon receipt, you must immediately contact the
transportation company who delivered the item to you and initiate your claim with same. If this procedure is not followed, it may affect the warranty status of
the unit.

LIMITED

EQUIPMENT WARRANTY

All workmanship and material in Star products have a one (1) year limited warranty on parts & labor in the United States and Canada. Such warranty is limited
to the original purchaser only and shall be effective from the date the equipment is placed in service. Star's obligation under this warranty is limited to the repair
of defects without charge, by the factory authorized service agency or one of its sub-agencies. Models that are considered portable (see below) should be taken
to the closest Star service agency, transportation prepaid.

> Star will not assume any responsibility for loss of revenue.
> On all shipments outside the United States and Canada, see International Warranty.
* The warranty period for the JetStar six (6) ounce & Super JetStar eight (8) ounce series popcorn machines is two (2) years.
* The warranty period for the Chrome-Max Griddles is ve (5) years on the griddle surface. See detailed warranty provided with unit.
* The warranty period for Teon/Dura-Tec coatings is one year under normal use and reasonable care. This warranty does not apply if damage occurs to

Teon/Dura-Tec coatings from improper cleaning, maintenance, use of metallic utensils, or abrasive cleaners, abrasive pads, product identiers and

point-of-sale attachments, or any other non-food object tha comes in continuous contact with the roller coating. This warranty does not apply to the
“non-stick” properties of such materials.

> This warranty does not apply to "Special Products" but to regular catalog items only. Star's warranty on "Special Products" is six (6) months on parts

and ninety (90) days on labor.

> This warranty does not apply to any item that is disassembled or tampered with for any purpose other than repair by a Star Authorized Service Center or

the Service Center's sub-agency.

> This warranty does not apply if damage occurs from improper installation, misuse, wrong voltage, wrong gas or operated contrary to the Installation and

Operating instructions.

> This warranty is not valid on Conveyor Ovens unless a "start-up/check-out" has been performed by a Factory Authorized Technician.

PARTS WARRANTY

Parts that are sold to repair out of warranty equipment are warranted for ninety (90) days. The part only is warranted. Labor to replace the part is chargeable to
the customer.

SERVICES NOT COVERED BY WARRANTY

PORTABLE EQUIPMENT

Star will not honor service bills that include travel time and mileage charges for servicing any products considered "Portable" including items listed below.
These products should be taken to the Service Agency for repair:

1. Travel time and mileage rendered beyond the 50 mile radius limit

2

. Mileage and travel time on portable equipment (see below)

3

. Labor to replace such items that can be replaced easily during a daily cleaning

routine, ie; removable kettles on fryers, knobs, grease drawers on griddles, etc.

4. Installation of equipment

5. Damages due to improper installation

6. Damages from abuse or misuse

7. Operated contrary to the Operating and Installation Instructions

8. Cleaning of equipment

9. Seasoning of griddle plates

10. Voltage conversions
11

. Gas conversions

12. Pilot light adjustment

13. Miscellaneous adjustments

14. Thermostat calibration and by-pass adjustment

15. Resetting of circuit breakers or safety controls or reset buttons

16. Replacement of bulbs

17. Replacement of fuses

18. Repair of damage created during transit, delivery, &
installation OR created by acts of God

* The Model 510FD Fryer.
* The Model 526TOA Toaster Oven.
* The Model J4R, 4 oz. Popcorn Machine.
* The Model 518CMA & 526CMA Cheese Melter.
* The Model 12MC & 15MC & 18MCP Hot Food Merchandisers.
* The Model 12NCPW & 15NCPW Nacho Chip/Popcorn Warmer.
* All Hot Dog Equipment except Roller Grills & Drawer Bun Warmers.
* All Nacho Cheese Warmers except Model 11WLA Series Nacho Cheese Warmer.
* All Condiment Dispensers except the Model HPD & SPD Series Dispenser.
* All Specialty Food Warmers except Model 130R, 11RW Series, and 11WSA Series.
* All QCS/RCS Series Toasters except Model QCS3 & RCS3 Series.
* All Fast Steamer Models except Direct Connect Series.

10

®

Blu

Red

Red

Red

Red

Org

Org

Blk

Blu

Blu

Blu

Blu

Yel

Wht

Wht

Wht

Wht

Maj

Maj

Red

Red

Blk

Blk

Blk

Blk

MODEL:

QCS-3-1300 208/220/240V w/FUSE

Q3-95ARB 208/240 w/FUSE

THIS DRAWING CONTAINS INFORMATION CONFIDENTIAL TO STAR MFG. INT'L. INC.

NO REPRODUCTION OR DISCLOSURE OF ITS CONTENTS IS PERMITTED.

SK2255 Rev -

06/8/2007

FAN MOTOR

POWER SAVER

3

1

RESET/HIGH LIMIT

BOTTOM

4

2

HEAT

MOTOR

DRIVE

H1

PILOT

L1

H2

L2

CORD

POWER SUPPLY

TOP HEAT

PILOT

H1

L1

H2

L2

CONTROL

SPEED

CONTROL SIDE

LEFT SIDE

BOTTOM HEAT

TOP HEAT

FUSES

11

34

2

3

4

6

12

13

14

15

171921

1820

16

13

19

33

22

23

24

25

26

27

29

31

30

35

36

37

38

28

32

49

39

40

42

41

43

44

48

45

46

47

5

1

50

7

8

9

10

11

MODEL: 9H-

Q3-95ARB 208/240V CONVEYOR TOASTER

THIS DRAWING CONTAINS INFORMATION CONFIDENTIAL TO STAR MFG. INT'L. INC.

NO REPRODUCTION OR DISCLOSURE OF ITS CONTENTS IS PERMITTED.

SK2227 Rev. E 6/28/2007

Sticker Nameplate

12

PARTS LIST Dec 1, 2010, Rev. E

Q3-95ARB-V02 & Q3-95ARB-VO4

Conveyor Toaster

Number

Key

Number

1 2M-Z10370 1 LABEL - TOASTER WARNING
2 HH-101371 1 ENCLOSURE,
3 HH-402470 1 PANEL, BACK,
4 2U-200561 1 MOTOR, FAN
5 2E-200566 1 SWITCH, HIGH LIMIT RESET
6 2U-200509 1 MOTOR, DRIVE, FAN BLADE NOT INCLUDED
2R-Z8879 1 2-5/8 DIA FAN BLACK FAN BLADE, MOTOR
7 2C-1487 2 SCREW 6-32X1/4 RHP ST, FUSEHOLDER
8 2C-H8669 2 WASHER #6 INT STL NP
9 2C-2553 2 NUT 6-32 HEX STL NP
10 2E-Z5681 1 FUSEHOLDER, CLASS G
11 2E-Z5680 2 FUSE, 5A - CLASS G
12 2A-202902 1 SHAFT, DRIVE
13 HA-112261 2 BUSHING, REAR
14 2P-Z8779 1 SPROCKET, DRIVEN (25B11 X 5/16”)
15 2P-200645 1 SPROCKET, DRIVE (25B17 X 5/16”)
16 2P-150013 1 CHAIN, DRIVE (19”)
17 2P-115501 3 JUMPER, TERMINAL BLOCK, SMALL, 2 POS.
18 2P-115502 1 JUMPER, TERMINAL BLOCK, SMALL, 3 POS.
19 H9-Z10283 2 BLOCK, TERMINAL. SMALL, 4 POS.
20 H9-Z10282 1 BLOCK, TERMINAL, SMALL, 10 POS.
21 HH-Z10236 1 SPACER - TERMINAL BLOCK
22 2R-200562 1 GUARD, FAN MOTOR
23 2A-Z11501 4 FOOT-1" SOLID RUBBER
24 2P-200736 2 SPRING, BUSHING, FRONT
25 2P-200700 2 TEFLON BEARING
26 2A-202905 1 SHAFT, IDLER
27 SP-160028 1 CONVEYOR, BELT (14” X 35”)
28 2B-200603 3 LINK, MASTER, CONVEYOR BELT
29 HH-100561 1 TRAY, PULL-OUT
30 2R-200788 1 GUARD, CRUMB TRAY
31 HH-Z10127 1 TRAY, CRUMB
32 2A-Z9394 2 SPRING BEARING HOUSING
33 2A-200284 1 E-CLIP
34 HH-100572 1 BAFFLE, AIR FLOW HI
35 2E-200551 1 SWITCH, ROTARY POWER SAVER
36 2J-200538 2 SWITCH, INFINITE
37 2P-402728 1 ANTI-SPIN PLATE
38 HB-120261 1 SPD CTRL, 500 OHM, w/600V DIODE 2 wires
39 2M-Z10269 1 LABEL, CONTROL PANEL
40 2R-200769 1 KNOB, POWER SAVER (before 1101)
41 2R-200768 3 KNOB, SPEED CONTROL, INFINITE SWITCH
42 2R-200708 4 CAP, KNOB
43 HH-Z10230 1 HOUSING - RECEPTACLE
44 2R-Z10228 1 SNAP-IN RECEPTACLE 1/4 TURN FAST
45 2R-Z10227 1 RETAINER
46 HH-Z10229 1 LOCKING COVER
HC-Z12006 1 CONTROL COVER Q3-95ARB-208/240V mfg after 1/2009
47 2R-Z10226 1 1/4 TURN FASTENER

48 HH-Z10124 6 HEATER TUBE QUARTS, 208V (700W, 6.86 Ω, 69.3V) 208V
HH-Z10138 6 ELEMENT QUARTZ, 240V (700W, 9.0 Ω, 80V) 240V

49 HC-402499 1 RETAINER, ELEMENT, 6 TUBE
50 PS-120251 1 THUMB SCREW COVER KIT

Part

Number

Per

Unit

Description

NI 2B-200602 1 LINK, CONVEYOR BELT
NI 2E-Z10181 1 CORD SET 12/3, POWER (NEMA 6-30)
NI 2E-Z9841 1 CORD, FAN MOTOR
NI 2K-200465 1 BUSHING, CORD HEYCO
NI 1P-Z8914 1 EXTREME PRESSURE MULTIPURPOSE SYNTHETIC GREASE (80°F TO 400°F) 8 oz. TUBE
NI HH-Z10125 1 HEAT SHUTTER SWINGING
NI HC-120279 1 WIRE KIT FOR FUSE

13

Following Pages

Redesign unit implemented 5/2008

Models: Q3-95ARB-208V & 240V

• Simplied Wiring

• Fewer Terminal Blocks

• Identical Outside Apperance

• Metal Nameplate

14

WD# 2M-Z10835

QCS & RCS WIRED IN SERIES

FAN MOTOR

RESET/HIGH LIMIT

BOTTOM

4

2

HEAT

MOTOR

DRIVE

H1

PILOT

L1

H2

L2

14GA CORD

POWER SUPPLY

PILOT

H1

L1

H2

L2

CONTROL

SPEED

CONTROL SIDE

LEFT SIDE

BOTTOM HEAT

TOP HEAT

TOP
HEAT

3 BLACK

4 WHITE

BLACK

1 BLACK

WHITE

BLACK

6

11 BLACK

13 BLACK

12

10

WHITE FOR 208V

5 BLACK

7 BLACK

MOTOR WIRE

IS 18GA

GND

WHITE OR BLUE

WHITE

9

BLACK

WHITE

WHITE

15 BLACK

FUSE

FUSE

2 WHITE

4 WHITE

14 WHITE

BLACK

16 WHITE

1

3

8 WHITE

MODEL:

QCS & RCS 3 wired in Series

THIS DRAWING CONTAINS INFORMATION CONFIDENTIAL TO STAR MFG. INT'L. INC.

NO REPRODUCTION OR DISCLOSURE OF ITS CONTENTS IS PERMITTED.

STAR MANUFACTURING INTERNATIONAL INC.

SK-Z10835 Rev B 1/2008

®

15

32

Metal Nameplate

MODEL:

Q3-95ARB-208/240V CONVEYOR TOASTER

THIS DRAWING CONTAINS INFORMATION CONFIDENTIAL TO STAR MFG. INT'L. INC.

NO REPRODUCTION OR DISCLOSURE OF ITS CONTENTS IS PERMITTED.

STAR MANUFACTURING INTERNATIONAL INC.

SK2369 Rev - 5/01/08

®

2

3

4

7

6

13

14

15

16

17

13

31

20

21

22

23

24

25

27

29

28

18

33

34

35

36

26

30

48

37

38

40

39

41

42

47

43

44

45

1

46

8

9

10

11

12

5

18

19

16

PARTS LIST September 14, 2009, Rev. F

Q3-95ARB-208V & Q3-95ARB-240V

Conveyor Toaster

Number

Key

Number

1 2M-Z10370 1 LABEL - TOASTER WARNING
2 HC-120283 1 CHASSIS ENCLOSURE ASSY
3 HC-Z11212 1 BACK PANEL,QCS-3
4 2U-200561 1 MOTOR,FAN240V 23BTM
5 2E-200566 1 SWITCH, RESET, 0796
6 2R-Z8879 1 2-5/8 DIA FAN BLACK CW
7 HB-120262 1 MOTOR ASSY 208-240V
8 2C-1487 2 SCREW 6-32X1/4 RHP STL NP
9 2C-H8669 2 WASHER #6 INT STL NP
10 2C-2553 2 NUT 6-32 HEX STL NP
11 2E-Z5680 2 FUSE, 5A - CLASS G
12 2E-Z5681 1 FUSEHOLDER, CLASS G
13 2A-202902 1 SHAFT, T714 DRIVE
14 HA-112263 2 BEARING ASSY PTFE/BRONZE
15 2P-Z8779 1 SPROCKET 25P-11T .313 ID
16 2P-200645 1 SPROCKET, 25B17 X 5/16
17 2P-150013 1 DRIVE CHAIN #25 ROLLER
18 2E-Z10406 2 TERMINAL BLOCK 4 POS
19 2E-Z9736 1 TERMINAL BLOCK - POWER
20 2R-200562 1 FAN GUARD
21 2A-Z11501 4 FOOT-1" SOLID RUBBER
22 2P-200736 2 2 INCH BEARING SPRING
23 2P-200700 2 SPRING LOAD BEARING TEFLO
24 2A-202905 1 SHAFT, 214HX IDLER
25 SP-160028 1 CONVEYOR, BELT (14” X 35”)
26 2B-200603 3 BELT LINK 14IN SPACECLIP
27 HH-100561 1 TRAY, PULL OUT, QCS, 14
28 2R-200788 1 QCS-3 CRUMB TRAY GUARD
29 HH-Z10127 1 CRUMB TRAY
30 HA-Z9743 2 SPRING RETAINER (2)
31 2A-200284 1 E-CLIP 5/16"
32 HC-120285 1 ASSY, AIR BAFFLE QCS-3 HI
33 2E-200551 1 SWITCH ROTARY
34 2J-200538 2 SWITCH, EGO 240V INFINITE
35 2P-402728 1 POT, ANTI SPIN PLATE
36 HB-120261 1 SPEED CONTROL ASSY 500
37 2M-Z10269 1 LABEL QCS-3-95ARB CONTROL
38 2R-200768 1 KNOB, CONTROL Q SERIES
39 2R-200769 3 KNOB, POWERSAVER Q SERIES
40 2R-200708 4 KNOB, CONTROL CAP
41 HH-Z10230 1 HOUSING - RECEPTACLE
42 2R-Z10228 1 SNAP-IN REC.1/4 TURN FAST
43 2R-Z10227 1 RETAINER - 1/4 TURN FAST
44 HH-Z10229 1 LOCKING COVER 95ARB
45 2R-Z10226 1 1/4 TURN FASTENER, BAIL
46 PS-120251 1 THUMB SCREW COVER KIT
47 HH-Z10124 6 HEATERTUBE, QUARTZ 700W 208V
HH-Z10138 6 ELEMENT QUARTZ 700W 80V 240V
48 HC-Z10389 1 ELEMENT RETAINER,LFT,QCS­ HC-Z10390 1 ELEMENT RETAINER,RHT,QCS­ NI 2B-200764 1 LOADUP, 14 EURO, WIRE
NI 2E-Z10181 1 CORD SET 12/3, 6-30P 80IN
NI 2K-200464 2 BUSHING, WIRE RING 7/8"
NI 2K-200465 1 BUSHING,CORD HEYCO12/3 BL
NI 2K-Y1139 1 BUSHING HEYCO SB500-6
NI D9-Z10878 1 CORD SET 12/3 NEMA 6-30P
NI HH-Z10125 1 HEAT SHUTTER SWINGING

Part

Number

Per

Unit

Description

17

STAR INTERNATIONAL HOLDINGS INC. COMPANY

Star - Holman - Lang - Wells - Bloomeld - Toastmaster

10 Sunnen Drive, St. Louis, MO 63143 U.S.A.

[phone]

www.star-mfg.com