Hollywood Racks HR1000R User Manual

Sport Rider

Recumbent Rack



1

O

SMALL WHEEL ADAPTERS

2

O

HOLLYWOOD RAC

KS

Model HR1000R – 2 Bike Hitch Rack

with Precision-Slide clamping system

ID# Description Qty
A MAIN RACK ASSY 1

B SHORT FRAME HOOK 1
C LONG FRAME HOOK 1
D RECEIVER TUBE & SPACER
E LEFT SIDE WHEEL TRAY 2
F RIGHT SIDE WHEEL TRAY 2
G REC. TUBE STOP BOLTS 2
H LOWER BRACKET 1
I 8MM BOLTS 4
J FLAT WASHERS 4
K 5MM HEX KEY 1
L LOCK WASHERS 2
M ½-13 THREADED HITCH PIN 1
N HITCH PIN CLIP 1
P WHEEL TUBE STOP SCREWS 2

Not to be used on any trailer, fifth
wheel or vehicle being towed by
another vehicle

 Weight Limit 45lbs/20 kg per bike
 2 bike maximum capacity

 Optional locking kits available

D

A

F

E

1

Fig. 1

Assembly & Installation Procedure:
Step 1: Locate holes on main rack assembly,

bracket and hardware (Fig. 1)
Step 2: Loosely assemble bracket to main

rack as shown in Fig. 2 & 3. Bolts (I) inserts
through lock washer (L), then flat washer (J),
then top plate and into bottom plate Do Not
tighten!

Step 3: Slide main rack assembly onto
Receiver tube as shown in Fig. 4 & 5.
Adjust position so that is 3 or 4 inches
between the end of the rack and end of the
receiver tube. Tighten using hex wrench
provided or equivalent. Note: Final position

of vertical portion of the rack can be re­adjusted after you have installed the rack on
your vehicle

Step 4. Insert “stop bolts” (G) through hole in
receiver tube as indicated.
See Fig. 6.

Fig. 2

Fig. 3

washers

Fig. 4

Step 5a: Install Wheel holders:

Fig. 5

Fig. 6

Fig. 7

Step 6:

Installing into a 1 ¼” trailer

Note: The receiver tube comes

ready for installation into a 2”

using a ¾” wrench.

Fig. 13

Fig

. 14

Fig. 15

hitch. If you have a 1 ¼” hitch,
use the provided hex wrench to
remove the plastic spacer as
shown in Fig. 9.
Place lock washer and flat washer
onto hitch pin bolt as indicated.
Insert the receiver tube into the
hitch. Align the holes, insert the
hitch pin bolt and tighten securely

Fig. 9

Fig. 8

Fig. 10

Step 6 A: Installing into a 2”trailer hitch

Place lock washer and flat washer onto hitch pin
bolt as indicated. Insert the receiver tube into the
hitch. Align the holes, insert the hitch pin bolt

and tighten securely using a ¾” wrench.

Fig. 12

Fig. 11

Important! When inserting the hitch pin
bolt, the bolt should pass through the
receiver tube first then through the
plastic spacer.

Install Hitch pin clip
after tightening bolt

3

Installation and operation of “Precision

-

Slide” Clamp System

Step 1: Install the “Precision Slide” clamps on the vertical post:

Position the long frame hook on top of the round vertical post facing the
vehicle. Squeeze the lever and the tab together, so that the lever is all
the way up (engaged). Now wiggle the plastic housing down onto the
tube aligning the index guides with the index slots. You may have to
gently tap it with your other hand. Remember the lever must be
engaged to install it onto the tube. Repeat for the short hook facing
in the opposite direction.

Step 2: Using the clamps:

After the clamp is installed, it can only be raised by engaging the
lever. The clamp can physically be pushed down without engaging the
lever but it is highly recommended that the lever also be engaged
when lowering the clamp.

Installation of small wheel holders

Folding Down Vertical Post

For easy access to the cargo area, the vertical post can

Folding Up the Wheel Holders

16b

16a

be folded down. To fold down vertical post, rotate and
remove the side-retaining pin as shown in Fig. 16a-16d.
Be sure to re-tighten the thumbscrew after replacing pin.

16d

16c

To fold up the wheel holders, rotate and remove
the front retaining pins. Then rotate the tube up
and re-install the pins. See Fig. 17a &17b

17a

17b

Installing Bikes on the Rack

Tips for carrying

Pre-position the wheel trays to fit the bike’s wheel base (center to center distance between the

wheel axels) such that they are directly beneath each wheel. To adjust the wheel trays, loosen
the knobs and slide along the wheel holder support tube. Tighten knobs securely.

To fit the first bike (closest to the vehicle) more easily, the vertical post may be tilted down
(away from vehicle). To do this, simply remove the side retaining pin per. Note: Never fold
down main tube with bike(s) mounted. Place the first bike in the wheel holders, and then rotate
the vertical post up per Fig 16d. Handlebars for the first bike should be on the driver’s side of
the vehicle. If carrying two bikes, always load the smaller bike first (position the smaller bike
between the vehicle and vertical post)

Be sure that the hooks are well supported on the bike’s frame. While engaging the lever, lower
the hook firmly down onto bike frame as shown in Fig 18d. Try pulling up on the hook to be
sure the clamp is properly engaged. Use the Velcro strap on the wheel holder as the final step
of installing the bikes on the rack, per Fig. 18e.

woman’s bikes and
bikes with slanted
top tubes

Adjust the wheel
trays so that the
hook will rest in the

bike frame’s top tube
and seat tube, as
shown in Fig. 19a
and 19b.

18e

19a

Double check before driving off

Limited Lifetime Warranty (effective January 1, 2008):

Final Step:

Install wheel tube stop screws: After you have installed the

Fig. 20a

Fig. 20b

bikes on the rack and are comfortable with the positions of the wheel holders,
the stop screws can be installed. Locate items P from hardware bag. Thread
them into the hole located on the bottom of wheel tubes (Fig. 20), and tighten
with a flat edge screwdriver. The screws are removable.

Optional accessories for your Sport Rider

:

Locking Threaded
hitch pin with
security cable

part no. LHPTC

Locking threaded
hitch pin

part no. LHPT

- Knobs are tight on all four wheel trays and

- Frame hooks are pushed all the way down

- All three retaining pins are properly inserted and secure

- Wheel straps are fastened

- Hitch pin is secure and hitch pin clip is installed

- Drive slowly on bumpy or dirt roads

Hollywood Racks will warrant its car racks and accessories during the time that an original retail purchaser owns the product subject
to the exclusions and limitations of this warranty. Hollywood Racks will remedy defects in materials and workmanship by repairing or
replacing (at its option) a defective part or the complete rack without charge for labor or parts. Hollywood Racks may elect (at its option)
to issue a refund equal to the purchase price paid for the product.

This warranty does not cover problems caused by normal wear and tear including (but not limited to) weather, scratches, dents, rust,
accidents, unlawful vehicle operation, misuse, abuse, neglect, theft, unauthorized modifications, or unauthorized repair. No warranty is
given for defects resulting in incorrect assembly, incorrect installation onto the vehicle, installation on a “no fit” vehicle, incorrect

attachment of bicycles onto the rack, or overloading of the rack’s weight restrictions. This warranty terminates if the original retail
purchaser transfers the product to any other person. If a product is believed to be defective, the original retail purchaser should contact
either the original retailer or Hollywood Racks directly at 800-747-4085 or at [e-mail]

Disclaimer of Liability: Repair or replacement of a defective product or the issuance of a refund or credit (as determined by Hollywood

Racks) is a purchaser’s exclusive remedy under this warranty. Damage to a purchaser’s vehicle, cargo, bicycles and or to any other
person is excluded. This warranty is expressly made in lieu of any and all other express warranties, whether oral or written.

Hollywood Racks shall not be liable for any direct, indirect, consequential, incidental, special, punitive or any other damages in
connection with the purchase, use or handling of this product. Some states do not allow the exclusion or limitation of consequential or
incidental damages and the above limitation may not apply to you. This warranty gives you specific legal rights and you have other
rights, which vary from state to state.

Trike

Adapter

Part No.

TRK-ADP

12812 S. Spring St. Los Angeles, CA 90061

Tel [phone] [phone] FAX [phone]

www.hollywoodracks.com email: [e-mail]

Customer Service Hours: M-F 8:00AM to 3:00 PM PST

Made in Taiwan 010710

Hollywood Racks

Quality bicycle racks since 1973