1
ALUMINIUM
GREENHOUSE
Riga S/Riga
Basic kit
assembly instructions
Subject to technical changes!
Current as of 09/2013
model Riga S
system width 2,32 m
system width 2,96 m
model Riga
2
Dear garden friend,
congratulations on the purchase of an aluminium greenhouse made by
The construction is simple. First read the assembly instructions and follow them step by step.
Parts and parts list
Please complete all boxes stored dry and protected from direct sunlight!
number of cartons
basic construction
(gable/eaves)
curved center
proles
windows/
doors
glazing
Riga S/II/III/IV 1 1 1 1
Riga III/IV/V 1 1 1 1
Start with the basic kit. Please do not open all the boxes at the same time. Let's not get confused
by the variety of items.
Before you begin assembly, check on the parts lists, if all parts are present. Each box goes
through a quality check before it is closed, thus missing parts are almost excluded. Should any
parts are missing, please give us the wrong position.
Customer Service: 877-760-8500 or 512-407-8500 sales@Exaco.com
Exaco Trading
10203 Metropolitan Dr.
Austin, TX 78758
Location
Choose, if possible, a sunny place for your greenhouse. Avoid the shadow of buildings and trees.
For vegeteables, like tomatoes, cucumbers and melons, make your greenhouse as possible in
north-south-direction. For owers and potted plants in east-west-direction.
Warning:
The greenhouse should preferably be placed in a sheltered spot and not in
stormy weather. It is dangerous to leave a partly assembled house!
With the correct assembly resists this greenhouse and strong winds. The manufacturer assumes
no responsibility for any damage by improper installation or acts of God.
The constructions of the greenhouse must be conducted by at least two people.
Work with secure, craft-oriented tools. Be careful when assembling on a secure stand of the ladder
(risk of accident!).
In principle, only with gloves on (risk of injury, average risk!).
3 - 5 mm 3 - 5 mm 6 - 8 mm
length
model
712 mm 768 mm 1030 mm
Riga S II 4 1 7
Riga S III 4 1 11
Riga S IV 4 1 14
3 - 5 mm 3 - 5 mm 6 - 8 mm
length
model
768 mm 1030 mm 1030 mm
Riga III 1 4 11
Riga IV 1 4 14
Riga V 1 4 16
3
For the conguration you need the following tools:
1 pc. Phillips screwdriver size 2
1 pc. foot-end wrench10 mm
1 pc. screwdriver
1 pc. allen key 3 mm (in the accessoires bag of the roof window)
1 pc. level
1 pc. stepladder
1 pc. le to remove any burrs on the proles
1 pc. rubber hammer
1 pc. tape measure
You should be careful:
Wedge seals (V23) pull
apart the center!
Push the seal 3 - 5 mm between the soil prole and the glazing.
Both within the greenhouse!
Important: This compress the seals because they contract in cold weather!
Hexagonal screws can also be inserted later in the plastic slider!
Plastic slider in the bottom door
frame, side and roof bars
numbers of wedge seals
pos.4-2
pos.4-1
pos.3-3
pos.1-5-6
pos.2-1
pos.2-3.1
pos.2-3.1
pos.1-1
pos.1-9
pos.1-9
pos.1-5-4
pos.1-5-4
pos.1-5-6
pos.1-7
pos.1-6
pos.1-8
pos.3-2
4
The ISO-Cellular sheets, speak glazing, always install the UV coated side out. The plates have
on the protective lm has a hint.
The protective lm, rst loosen the edges and only after the complete assembly pull it off
immediately. After several days of sunlight can burn the lm rmly on the plates and can be
solved only with difculty.
Do not pull the box right after the lm, otherwise you could not tell which side has the UV
protection!
Question: Do I have a greenhouse and the greenhouse glazing and "seal"?
In principle: No.
But we recommend the horizontal transitions of the glazing to the prole (see sketch -->
dashed line ----) sealed with neutral cure, silicone transparent, so that as little water and can
therefore get a little dirt in the glas shots.
Advantage: The greenhouse looks to length of optically better. The tendency to formation of
algae just takes considerably in these areas.
Moisture/water can also occur
within the glass/hollow chambers depending on the wheather, since the plastic plates are
not "water-vapor-permeable
solid", ie moisture occurs in the
form of water vapor into the
plate. This is possible a purely
optical disadvantage, however,
can not be avoided.
The plates can thus take no
damage, even at freezing temperatures.
Warning: Use only neutral cure silicone, otherwise it may lead to stress cracks in plastic de glazing. This is the most common silicone sealant.
It is in any hardware store or at HOKLAR-Therm for about 4 - 6 € available/
cartridge.
Cleaning and care:
The greenhouse with plenty of water such as car washing brush. In addition, using a little
detergent.
!!!Note: Important information for glazing!!!
overview pos. description
number/length in mm
type II type III type IV
6.1
foundation frame prole/
gable
2
2199
2
2199
2
2199
6.2
foundation frame prole/
eaves
2
2033
2
3091
2
4149
V26
foundation frame corner bracket
40/40/2 x 105
4
105
4
105
4
105
V27
mounting bracket
(rung/foundation frame)
10
135
10
135
10
135
S12
S1
hexagonal screw M6 x 12 +
nut M6
20 20 20
overview pos. description
number/length in mm
type III type IV type V
6.1
foundation frame prole/
gable
2
2835
2
2835
2
2835
6.2
oundation frame prole/
eaves
2
3091
2
4149
2
5207
5
Foundation frame for digging (optional)
Proles and accessoires for foundation frame
Riga S
:
Proles and accessoires for foundation frame
Riga
: (V26/V27/S12/S1 as above)
!!!Warning: Use only according to instructions under foundation. See below!!!
This is the easiest, safest and also foundation of a greenhouse.
The foundation frame is hooked force-t into the soil prole of the green-
house screwed into the corners with a corner angle (V26). (See page 6).
The foundation frame is assemble to coincide with the greenhouse
together.
Setting up the foundation frame
A small ditch, sod (about 10 - 12 cm deep), dug into the dimensions of the
foundation frame. Use in the corners as a paving stone according to the
other horizontally.
These are then the safe circulation and avoid "bagging" a possibly of the
greenhouse. The greenhouse and the foundation frame in this "gab" and set them
with earth ll.
Expedient is also the creation of garden slaps or stone pavement, so the
greenhouse at eg heavy rain is not covered by mud splashes is.
In addition, the work made easier around the greenhouse, such as mowing the
lawn.
item no 9999 0078
item no 9999 0267
item no 9999 0124 + 9999 0128
6
Note: The founda-
tion frame proles
are shorter than
soil proles!
Foundation of the greenhouse
We recommend that you use for the bolt in place anchor bolts. These are not included!
side rung/
door frame
mounting bracket
- offset - (V15)
bolt M6 x 12 (S12)
+ nut M6 (S1)
soil prole
The foundation frame proles separately in the soil
proles rotate and center align.
Note: The foundation frame proles are shorter than
soil proles!
To stabilisize the house,
the mounting bracket
(V27) using bolts M6 x 12
(S12) retracted bolted to
the foundation frame and
the side rungs or door
frames.
In the foundation frame proles in the corner of
one bolt M6 x 12 (S12) to move, corner brackets
(V26) and fasten with nut M6 (S1).
Assembly foundation frame
model
foundation greenhouse
B1 L1
B2 L2
Riga S II
249 232 233 216
Riga S III
249 338 233 322
Riga S IV
249 443 233 427
Riga III
312 338 296 322
Riga IV
312 443 296 427
Riga V
312 533 296 533
7
Foundation plan Riga S/Riga
all dimensions in [cm]
Foundation of your greenhouse with a strip foundation
If you have not bought a foundation frame, the secure foundation by means fo strip
foundation. Then please create such a foundation in accordance with the specied
dimensions below.
You have set up your possibility to the greenhouse on low cur stones such as,
50 x 25 x 8 cm or better 50 x 30 x 10 cm.
Please note that the foundation is made evenly horizontally.
The greenhouse then please anchoring with the included mounting brackets (V15)
with the dowels (minimum)
Screws and ancors are not included.
exterior edge of the foundation
exterior edge of the greenhouse
upper edge of ground
frost-free ground
overview pos. description
number/length in mm
Riga S Riga
II III IV III IV V
2.1
soil prole/eaves
2
20722313024188231302418825246
2.3 side rung - curved 2 4 6 4 6 8
3.2 cross bar/roof window
1
10201102021020110202102041020
3.3 ridge prole
1
21371319514253131951425315311
3.4 angle stabilization
4
21044316244220431624422045278
overview pos. description
number/length in mm
Riga S Riga
II III IV III IV V
1.1
soil prole/gable
2
22382223822238228742287422874
1.5.4
rand rung left - curved 2 2 2 2 2 2
1.5.6
rand rung right - curved 2 2 2 2 2 2
1.6
door frame left
with slant
2
18762187621876220592205922059
1.7
door frame right
with slant and drilling
2
18762187621876220592205922059
1.8
door frame above
2
758
2
758
2
758
2
758
2
758
2
758
1.8
cross bar
in the side door without
1
758
1
758
1
758
1
758
1
758
1
758
1.9
cross bar left and right
4
702
4
702
4
702410204102041020
8
Content main box - basic kit Riga S/Riga
Please check in the tables list the completeness of the components.
Proles for both gables:
Proles for eaves:
overview pos.
description/
item number
num-
ber
Riga S
num-
ber
Riga
V9 corner soil prole
4 4
V5 connecting plate
Ortgangprol/Türzarge
4 4
V10
connecting plate 90 x 35 mm
mounting
cross bar/rear
2 2
V11
endplate ridge/gutter
2 2
V4 connecting plate
for cross bar/roof window
II = 2
III = 2
IV= 4
III = 2
IV = 4
V = 8
V12
corner
30/30/2/15 mm
soil prole
screw the corner from inside
4 4
S21 blind plug Ø10 mm
rand rung -drilling cross bar
4 4
V14
hose section 760 mm lg.
door threshold seal
1 1
V23 wedge seal 3 - 5 mm
sealing the soil prole inside
See
table
below !
See
table
below!
S9
self-tapping screw pan head
4,2 x 13
door frame-soil prole/
cover plate/corner (V12)
38* 38*
S13
self-tapping screw pan head
4,8 x 45
gable
6 6
S5/S1hexagnal screw M6 x 16
+ nut
screws for pulling
II = 40*
III = 40*
IV = 44*
III = 40*
IV = 44*
V = 48*
V15
mounting bracket - offset
74 x 30 x 33 mm
for the attachement of the
greenhouse on foundation by
customer (not with foundation
frame)
10 10
S32
washer A6,4
door frames, roof and side
rungs
20
20
V = 24
V1
mounting corner bracket
inside
je
2x lks.
2x rts.
je
2x lks.
2x rts.
9
Accessories bag basic kit Riga S/Riga
item no 9999 0003
item no 9999 0028
item no 9999 0030
item no 9999 0075
item no 9999 0031
item no 9999 0072
item no 9999 0097
item no 9999 0181
item no 9999 0119
item no 9999 0144
item no 9999 0207
item no 9999 0183 + 9999 0128
item no 9999 0150
item no 9999 0173
item no 9999 00074
Riga S Riga
730 x 728 1048 x 728
10
ATTENTION! When using a foundation frame assemble in advance on this soil prole (see page S. 5, 6)
soil prole (pos.1.1)
door frame right (pos.1.7)
door frame left (pos.1.6)
corner soil prole (V9)
step 1
glazing
glazing
self-tapping screw pan head 4,2 x 13 (S9)
Note: Only after the screw mounting of the door -->
ability to align.
cross bar (pos.1.9)
cross bar (pos.1.9)
view from inside
self-tapping screw pan head 4,2 x 13 (S9)
connecting plate (V5)
screw M6 x 16 (S5)
with nut M6 (S1)
glazing
door frame
above
(pos.1.8)
glazing
to step 1:
First, please slide the door frame
left (pos.1.6) and the door frame
(pos.1.7)
(prole with 8 drill holes, a 30° chamfer and
a black plastic glide)
up to the small holes in the middle
of the soil prole. The chamfer must
show this to the outside. Then attach the corner bracket (V9) on the
soil prole.
step 2
Assembly procedure gable
to step 2:
Even now you need the small side
windows.
Dimensions are listed in the table.
With bar direction - vertical - in the
soil prole and sideways while in the
door frame.
step 3 to step 3:
Now the cross bar (pos. 1.9) is inserted from the top of the glazing.
step 4 to step 4:
Before the connecting plate (V5)
with the door frame above (pos.1.8)
screwed, slide in the vertical door
frames (pos.1.6/1.7) two hex screws
M6 x 16 (S5) and in the horizontal
door frame in M6 x 16 (S5) one.
view from inside
11
ATTENTION! When using a foundation frame assemble in advance on this soil prole (see page 5, 6)
glazing
rand rung right - curved (pos.1.5.6)
rand rung left - curved (pos.1.5.4)
rand rung to the corner connection peg plugged
The rear gable is assembled in the same way!!!
glazing
Only rear gable!
cross bar
(Pos.1.8)
step 5 to step 5:
The square peg of the corner connector is plugged in the rand rung
(pos.1.5.4/1.5.6).
Small triangular glazing positioned
on the door frame (pos.1.8).
The rand rung by means of
connecting plate (V5) screwed to
the door frame. On the rand rung
you need 2 self-tapping screws pan
head 4,2 x 13 (S9), on the door
frame 2 hexagonal screws M6 x 16
(S5).
- See also step 4! -
step 6: to step 6:
The cross bars (pos.1.9) are
mounted sideways with the selftapping screw pan head 4,8 x 45
(S13).
step 7:
view from outside
to step 7:
Slide before mounting the cross
bar required hex screws M6 x 16
(S5) into the prole of the cross bar
(pos.1.8 und 1.9).
The cross bar in the rear gable
is used the same height as the
existing cross bar. Attachment is to
the connecting plate (V10).
Now comes the glazing
(787 x 728 mm).
The remaining opening is later
closed by the supplied rear window.
Assembly procedure gable
view from inside
holes for
door lock
1x
M6x164xM6x16
1x
M6x16
connecting
plate (V10)
overview pos. description
num-
ber
length in mm
4.1
roof window prole 2 541
4.2 roof window prole 2 953
overview pos. description/item number
num-
ber
length in mm
*
V25 T-seal
2
1
641
1052
V13
corner with grub screw, internal hex and at point 4
V21
allen key 1
S12/S1hexagonal screw M6 x 12
nut M6
3
V24 corner bracket/roof window
4
12
Proles for roof windows (per roof window)
Content accessories bag roof window (per roof window)
* Note: The seal is bundled in one strand for all doors and windows, please cut accordingly.
You should be careful:
T-seals (V25) for all doors and windows
(total: 15 meters)
Attention! When the roof window for
pushing into the ridge the T-seal at
this side omit!!!
In the door area the hose section(V14)
is pressed into the soil prole. (As a
stop/seal to protect from dirt into the
soil prole).
Attention! In the bottom door is
rst pressed the seal, and only
then will the rectangular tube
screwed!
item no 9999 0032
item no 9999 0070
item no 9999 0056
item no 9999 0128
item no 9999 0005
item no 9999 0124
13
Assembly roof window
corner with grub
screw (V13)
window prol (pos. 4.1)
window prol (pos. 4.1)
window prol (pos.4.2)
(Pull in this prole no seal!)
Recommendation!
It is advisable to seal up around the window and the corner
bracket, thus no moisture can occur.
Attention: In the bottom cross prole inserting two hex
screws M6 x 12 (S12) for the window opener!
window prole (pos. 4.2)
corner bracket/roof window (V24)
automatic roof window opener
Mounting roof window
wrong!!!
right
Please push the roof window from the gable
side into the ridge and slide in position.
Automatic window opener mount.
First you screw three proles, then use the glazing and nally
attach the fourth prole.
14
Insertion of the seal in the roof window area
Please insert all the 4 plastic
corner connectors with silicone and seal the transitions
cleanly ( ).
cross-section
of the seal
length: 2,3 m
pos. 3.2
pos. 4.1
The seal is inserted as the sketch above.
Attention: Seal does not cut into the corners! Important!
The transitions of the glazing and the corner bracket/roof window to roof
window prole, please seal it with silicone → see sketch.
Here you need seal all around ( )!
side rung
pos. 2.3
cross bar
pos. 3.2
window prole
pos. 4.1 und 4.2
pos. 4.1
▲
▲
▲
▲
▲
▲
1 window opener
2 pressure cylinder
3 cotter pin
4 mounting plate window prole
5 mounting plate cross bar
15
Parts window opener
If the greenhouse is not "frost-free" hold, we recommend you to remove the entire window opener or only the pressure cylinder. Please keep the window opener in a dry or frost-free place.
Before reassembly in the spring especially the cylinder rod and the cylinder threads are greased to check if it is. The cylinder rod check for ease of movement, please.
The window opener needed after the assembly about 3 - 4 hours to adjust the temperature in
the greenhouse. The more you screw the pressure cylinder into the threaded device, the earlier and more highly opens the window. Do you want earlier/higher opening, turn the pressure
cylinder clockwise. In a later/lower opening counter-clockwise, with one turn is about 0,5°C.
Please keep in mind that can vary the temperature in your greenhouse and several window
openers have small tolerances.
Assembly instructions:
User guide - window opener -
1. Check whether the greenhouse window can open and close freely and unhinderedly.
Please remove from other manufacturers in advance the existing hand openers.
2. First install the window opener with the mounting plate (4) to the roof window prole (pos. 4.2).
3. Choose from the mounting plate (5) the middle hole and attach it to the cross rung (pos.3.2)
below the roof window.
4. The pressure cylinder at the upper end of threaded device secure with the cotter pin in the
t-coupling (upper hole).
Ajustment:
Winter-storage:
1
2
3
4
5
overview pos. description
num-
ber
length in mm
5.3.1
door prole bottom 1 700
5.6 door prole left
with hole for sash lock
1 692
5.7 door prole right
with hinge hole
1 692
5.9 door prole top
with transverse hole
1 700
5.8 square tube
with transverse hole
1 740
overview pos. description
num-
ber
length in mm
V51
metal hinge, black 2
V28 sash lock 1
V29 QR-stopper 30 x 30 x 1,5-2 2
*
V25 T-seal
2
2
710
744
S18
self-tapping screw countersunk head 4,8 x 25
(hinges)
8
S17
self-tapping screw countersunk head 4,2 x 45
(doors)
4
S19
self-tapping screw countersunk head 3,5 x 22
(sash lock)
2
S6 self-tapping screw pan head 3,5 x 38 (square tube) 2
V32 glazing block 30 x 10 x 4 2
V30/
V31
corner bracket door prole 4
16
Proles for divided revolving door - bottom -
* Note: The seal is bundled in one strand for all doors and windows, please cut accordingly.
Content accessories bag divided revolving door - bottom -
item no 9999 0358
item no 9999 0023
item no 9999 0032
item no 9999 0163
item no 9999 0160
item no 9999 0152
item no 9999 0138
left - item no 9999 0009
right - item no 9999 0011
item no 9999 0099
17
QR-stopper
(V29)
corner bracket door prole
(V30/V31)
Place the prole like the image on a at underground (possibly on cardboard or something
similar).
Square tube and door
prole top screw with
self-tapping screw pan
head 3,5 x 38 (S6).
Attention:
Move before sealing.
(see sketch!)
Assembly - divided revolving door - bottom -
view from outside
square tube (pos. 5.8)
door prole top (pos. 5.9)
sash lock (V28)
with self-tapping screw
countersunk
head 3,5 x 22
(S19) scews.
door prole right (pos. 5.7)
door prole left (pos. 5.6)
glazing block (V32)
self-tapping screw countersunk head 4,2 x 45 (S17)
door prole bottom (pos. 5.3.1)
* Note: The seal is bundled in one strand for all doors and windows, please cut accordingly.
overview pos. description
number/length in mm
Riga S Riga
5.1
door prole left
1
1081
1
1264
5.2 door prole right
with hinge hole
1
1081
1
1264
5.3 door prole top
1
700
1
700
5.4.1
cross bar
with hole for lockable door
handle
1
700
1
700
overview pos. description
number/length in mm
Riga S Riga
V52 door handle, lockable 1 1
S17
self-tapping screw countersunk head 4,2 x 45
(door)
6 6
V32 glazing block 30 x 10 x 4 2 2
*
V25 T-seal
2
710
2
710
2
1112
2
1295
V51
metal hinge, black 2 2
S18
self-tapping screw countersunk head 4,8 x 25
(hinge)
8 8
V28 sash lock, small 1 1
S19
self-tapping screw countersunk head 3,5 x 22
(sash lock)
2 2
V33 door locking device 1 1
S22
wing-type self drill, screw counters head 3,5 x 13
(door stop)
1 1
V30/
V31
corner bracket door prole 2 2
18
Proles for divided revolving door - top -
* Note: The seal is bundled in one strand or all doors and windows, please cut accordingly.
Content accessories bag - divided revolving door - top
left - item no 9999 0009
right - item no 9999 0011
outside - item no 9999 0035
inside - item no 9999 0244
item no 9999 0160
item no 9999 0032
item no 9999 0358
item no 9999 0163
item no 9999 0023
item no 9999 0152
item no 9999 0230
item no 9999 0189
19
Assembly - divided revolving door - top -
view from outside
Place the proles like the image on a at underground (possibly on cardboard or something
similar).
corner bracket door prole
(V30/V31)
Assembly o door locking
door prole top (pos. 5.3)
door prole right (pos.5.2)
door prole left (pos.5.1)
glazing block with sili-
cone x in position
cross bar (pos.5.4.1)
sash lock (V28) with self-tapping
screw countersunk head 3,5 x 22
(S19) screws
self-tapping screw countersunk
head 4,2 x 45 (S17)
* Note: The seal is bundled in one strand for all doors and windows, please cut accordingly.
1.
2.
3.
4.
overview pos. description
number/length in mm
Riga S Riga
5.1.2 door prole left
with hole for sash lock
1
1081
1
1264
5.2 door prole right
with hinge hole
1
1081
1
1264
5.3.1
door prole top
1
700
1
700
5.4.2 door prole bottom
with hole for window opener
1
700
1
700
overview pos. description
number/length in mm
Riga S Riga
S17
self-tapping screw countersunk head 4,2 x 45
(window)
6 6
V32 glazing block 30 x 10 x 4 2 2
V25 T-seal
2
710
2
710
2
1112
2
1295
V51
metal hinge, black 2 2
S18
self-tapping screw countersunk head 4,8 x 25
(hinges)
10 10
V28 sash lock, small 1 1
S19
self-tapping screw countersunk head 3,5 x 22
(sash lock)
2 2
V85 opener for rear window 1 1
V145
corner (xation of window) 1 1
S9 self-tapping screw pan head 4,2 x 13 2 2
V30/
V31
corner bracket door prole 2 2
S12/S1hexagonal screw M6 x 12
with nut M6
4 4
20
Proles for rear window
Content accessories bag - rear window -
* Note: The seal is bundled in one strand for all doors and windows, please cut accordingly.
*
item no 9999 0160
item no 9999 0358
item no 9999 0163
item no 9999 0023
item no 9999 0152
item no 9999 0303
item no 9999 0416
item no 9999 0144
left - item no 9999 0009
right - item no 9999 0011
item no 9999 0032
item no 9999 0124
item no 9999 0128
21
Assembly - rear window -
view from outside
door prole top (pos. 5.3.1)
door prole left (pos. 5.1.2)
door prole right (pos. 5.2)
glazing block with silico-
ne x in position
sash lock, small (V28)
with self-tapping screw
countersunk 3,5 x 22
(S19) screws
self-tapping screw
countersunk head
4,2 x 45 (S17)
cross bar
(pos. 5.4.2)
opener for rear
window
opener with self-tapping
screw pan head 4,2 x 13
(S9) screw
* Note: The seal is bundled in one strand for all doors and windows, please cut accordingly.
The required mounting bracket is placed on the
already collected bolts M6 x 16 (S5) and screwed
with nuts M6 (S1).
hex screw M6 x 12
(S12)
hex screw M6 x 16
(S5)
22
Assembly procedure - eaves -
soil prole (pos. 2.1) slide
to corner bracket
corner bracket (V12) screwed with
self-tapping screw pan head
4,2 x 13 (S9).
Slide the side glazing in the soil pro-
ile and rand rung and threading.
tip:
please solve the foil only at the
margin!
to step 9:
to step 8:
Now you need several hands or
corresponding aids.
Gable upright, hold and secure
support.
The ridge prole (pos. 3.3) now
introduce into the existing grooves/
slots of the gable, so that the
proles is ush with the front.
Now screw the end plate (V11) with
self-tapping screw pan head 4,2 x
13 (S9).
to step 10:
step 8
step 9
step 10
ATTENTION! When using a foundation frame assemble in advance on this soil prole (see page 5, 6)
ridge prole (pos. 3.3) at the gable and
end plate (V11) screw with self-tapping
screw pan head 4,2 x 13 (S9)
ridge prol (pos. 3.3)
ends support or
hold up it
insert the side glazing and
thread
First, the lateral soil proles on the
corner bracket on the gable attach.
23
Assembly procedure - eaves -
shown enlarged side
rung (pos. 2.3)
The side rung (pos. 2.3) above into
the ridge prole and below into the
soil prole to glazing insert it. There,
the plate is threading.
If neccessary, timber and plastic
hammer to get help.
Tip:
Greasing plastic gliders perhaps a
little!
to step 11:
Insert further side glazing and
rungs.
The connecting plate (V4) from
inside screwed with screw hex M6 x
16 and nut M6.
to step 12:
to step 13:
step 11
ATTENTION! When using a foundation frame assemble in advance on this soil prole (see page 5, 6)
step 12
step 13
Insert the remaining plates and
rungs now.
24
Assembly procedure - eaves -
step 15
to step 15:
to step 16:
step 16
ATTENTION! When using a foundation frame assemble advance on this soil prole (see page 5, 6)
step 14
to step 14:
The door gable is pre-mounted and
screwed.
For added stability must now
mounting inside corner (V1) be
attached. Use the self-tapping screw
pan head 4,2 x 13 (S9).
Install door and window.
Instructions, see page 12-21.
Mounting roof window
wrong!!! right
Represented
for the better
representation
plates cut.
The stabilization angle (pos 3.4)
become on both sides from inside
to the side rung with screw M6 x 16,
nut M6 and washer A6,4 screwed.
The angles are also proles for
rearward tables and shelves (see
separate instructions).
type of
house
gable
above
gable below
gable
triangular
door/
window
div. revolv.
door/bottom
rear gable
below
side plate
roof
window
below roof
window
number
size (a x b)
number
size (a x b)
number
size (a x b)
number
size (a x b)
number
size (a x b)
number
size (a x b)
number
size (a x b)
number
size (a x b)
number
size (a x b)
Riga II S
4
730 x 1135
4
730 x 728
2
779 x 239
2
724 x 1031
1
724 x 676
1
787 x 728
3
1048 x 2634
1
974 x 565
1
1048 x 1984
Riga III S
4
730 x 1135
4
730 x 728
2
779 x 239
2
724 x 1031
1
724 x 676
1
787 x 728
5
1048 x 2634
1
974 x 565
1
1048 x 1984
Riga IV S
4
730 x 1135
4
730 x 728
2
779 x 239
2
724 x 1031
1
724 x 676
1
787 x 728
6
1048 x 2634
2
974 x 565
2
1048 x 1984
Riga III
4
1048 x 1319
4
1048 x 728
2
779 x 239
2
724 x 1215
1
724 x 676
1
787 x 728
5
1048 x 3000
1
974 x 565
1
1048 x 2345
Riga IV
4
1048 x 1319
4
1048 x 728
2
779 x 239
2
724 x 1215
1
724 x 676
1
787 x 728
6
1048 x 3000
2
974 x 565
2
1048 x 2345
Riga V
4
1048 x 1319
4
1048 x 728
2
779 x 239
2
724 x 1215
1
724 x 676
1
787 x 728
6
1048 x 3000
4
974 x 565
4
1048 x 2345
b
a
a
a
a
aa
a
a
a
b
b
b
b
b
b
b
b
25
glas plan with ISO-cellular sheets 10 mm
Loading...