Hoist Fitness V HI-LO User Manual
V-HI-LO OPTION
HI-LO PULLEY
Note: Both Serial Number and Model Number are Required when Ordering Parts
RECORD SERIAL NUMBER HERE
MACHINE CODE
OWNER'S MANUAL
C08
Customer Service
(800) 548-5438
(858) 578-7676
Fax
(858) 578-9558
OWNER'S MANUAL
CONTENTS
INSTRUCTIONS .....................................................................
FRAME ASSEMBLY ..............................................................
PRE-ASSEMBLY....................................................................
DECAL PLACEMENT.............................................................
DECAL REFERENCE.............................................................
PART LIST...............................................................................
ABBREVIATIONS...................................................................
BOLT SIZING CHART............................................................
WASHER SIZING CHART......................................................
MAINTENANCE SCHEDULE.................................................
02
04
38
39
40
41
44
45
47
49
GENERAL MAINTENANCE INFORMATION........................
WEIGHT TRAINING TIPS.......................................................
WEIGHT RATIOS....................................................................
EXERCISE LOG......................................................................
LIMITED WARRANTY............................................................
50
51
52
53
54
PAGE 01
V HI-LO OPTION ASSEMBLY
OWNER'S MANUAL
INSTRUCTIONS
Before beginning assembly please take the time to read instructions
thoroughly. Please use the various lists in this manual to make sure that
all parts have been included in your shipment. When ordering, use part
number and description from the lists. Use only HOIST replacement parts
when servicing. Failure to do so will void your warranty and could result
in personal injury.
HOIST equipment is designed to provide the smoothest, most effective
exercise motion possible. After assembly, you should check all functions to
ensure correct operation. If you experience problems, first recheck the
assembly instructions to locate any possible errors made during assembly.
If you are unable to correct the problem, call your authorized HOIST dealer.
Be sure to have your serial number and this manual when calling. When all
parts have been accounted for, continue on.
TOOLS REQUIRED
Ratchet Wrench
1/2", 9/16" and 3/4" Sockets
Adjustable Wrench
Rubber Mallet
Tape Measure
Level
Hex Key Wrench Set
2 People Required For Assembly
V HI-LO OPTION ASSEMBLY
PAGE 02
OWNER'S MANUAL
***THIS PAGE WAS INTENTIONALLY LEFT BLANK***
PAGE 03
V HI-LO OPTION ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
V HI-LO OPTION ASSEMBLY
PAGE 04
**
OWNER'S MANUAL
FRAME ASSEMBLY
*
*
7
**
*
NOTE:
- HAND TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
REUSE EXISTING HARDWARE.
THIS PART IS ORIGINALLY
INCLUDED IN V-BASE UNIT,
REUSE UNLESS UNIT IS
TO BE USED WITH
LEG PRESS OPTION.
*
*
IMPORTANT:
IF V-BASE WAS PREVIOUSLY
*
ASSEMBLED, IT MAY BE
NECESSARY TO REMOVE V-BASE
WEIGHT STACK SHEILD.
*
*
8
PAGE 05
*
*
V HI-LO OPTION ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
**
*
*
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
ITEMS INCLUDED IN V-BASE UNIT,
*
REUSE EXISTING HARDWARE.
THIS PART IS ORIGINALLY INCLUDED
**
IN V-BASE UNIT, REUSE UNLESS UNIT
IS TO BE USED WITH HI-LO OPTION.
*
**
*
7
*
*
V HI-LO OPTION ASSEMBLY
PAGE 06
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- WRENCH TIGHTEN HARDWARE.
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
STEP 1 STEP 2
INSERT CABLE(2) AND
COUNTER WEIGHT
FROM BOTTOM AS
SHOWN.
SLIDE COUNTER WEIGHT
TOWARDS TOP AND PULL
CABLE (2) THROUGH.
9
2
25
74.75
2
PAGE 07
V HI-LO OPTION ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
- INSTALL CABLE AND PULLEYS AT THE
SAME TIME.
- WRENCH TIGHTEN HARDWARE.
19
2
47
2
9
40
55
40
9
V HI-LO OPTION ASSEMBLY
PAGE 08
53
41
OWNER'S MANUAL
FRAME ASSEMBLY
53
41
NOTE:
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
- WRENCH TIGHTEN HARDWARE (53) THEN
LOOSEN NUT JUST ENOUGH FOR (4,6)
TO PIVOT FREELY.
6
41
56
4
41
56
PAGE 09
V-HI-LO OPTION ASSEMBLY
GUARD ROD
NOTE:
BE SURE CABLE (3) IS
POSITION BETWEEN
PULLEY AND GUARD
ROD.
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
CABLING PROFILE VIEW
2
GUARD ROD
NOTE:
BE SURE CABLE (3) IS
POSITION BETWEEN
PULLEY AND GUARD
ROD.
3
V HI-LO OPTION ASSEMBLY
GUARD BOLT
NOTE:
BE SURE CABLE (3) IS
POSITION BETWEEN
PULLEY AND GUARD
BOLT.
PAGE 10
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
- WRENCH TIGHTEN HARDWARE.
21
48
55
40
4
6
40
21
PAGE 11
V HI-LO OPTION ASSEMBLY
STEP 1
OWNER'S MANUAL
FRAME ASSEMBLY
STEP 2
16
6
NOTE:
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
STEP 1
- SLIDE HI-LO ADJUSTER
ASSEMBLY (6) ONTO GUIDE
TUBE ASSEMBLY (9) AS SHOWN.
STEP 2
- INSERT THE CABLE ASSEMBLY (2)
THRU ADJUSTER ASSEMBLY (6)
AS SHOWN.
- THEN INSTALL CABLE LOCK (28)
ONTO CABLE ASSEMBLY (2)
TO FASTEN (2) TO (6).
STEP 3
- INSTALL THE RUBBER O-RING (16)
ONTO THE CABLE LOCK (28) TO
SECURE CABLE ASSEMBLY (2).
2
28
2
9
2
16
28
6
STEP 3
V HI-LO OPTION ASSEMBLY
PAGE 12
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
- HAND TIGHTEN HARDWARE.
9
8
9
40
55
61
40
PAGE 13
V HI-LO OPTION ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
40
NOTE:
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
- INSTALL CABLE AND PULLEYS AT THE
THE SAME TIME.
- HAND TIGHTEN HARDWARE.
51
40
55
10
20
2
V HI-LO OPTION ASSEMBLY
PAGE 14
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE
:
TILT TOP HEAD ASSEMBLY (10)
FORWARD AND INSERT
ADJUSTER TUBE ASSEMBLY (11)
INTO BASE ASSEMBLY (8)
10
NOTE:
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
14
31
NOTE:
BE SURE BEARING (14)
ALIGNS INSIDE CHANEL (31).
11
PAGE 15
8
V HI-LO OPTION ASSEMBLY
OWNER'S MANUAL
FRAME ASSEMBLY
NOTE:
- SOME PARTS MAY HAVE BEEN
REMOVED FOR CLARITY.
21
4
3
V HI-LO OPTION ASSEMBLY
311 5/16" 7907
3
PAGE 16
Loading...